Printable View
I have a set of 6 quick disconnect clips. Now you can replace your broken, pain in the ass to remove injector plugs with quick connect one. All have about 6" of tails for you to cut/solder these on.
Found more but they are going fast!!
One set left at $30.00 shipped!
http://3s.gonzoinc.com/albums/userpi...2/IMG_1023.JPG
Well that didn't take long.......SOLD
Damnit!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I may have some more around here somewhere. Give me a bit and I'll let you know Coop.
PM'ing you Coop
Find more lol
Post via Tapatalk
Well if there is that much interest I can get some more the next time I hit the yard. Maybe this weekend. I should be able to get another 3-4 sets Sunday/Monday
Better yet.... I just found another bad full of them!! I knew I had more around here I just thought I tossed them out, hence the reason I am going though everything again!
I'm going to go through them and make sure they are all still good as it is a wire ball of a mess right now. I'll post back up here in a bit when I get them all straightened out.
Ok guys. I found enough for 4 more sets!! Same price as before, $30.00 shipped.
First buyer gets the ones with the longer tails and next one gets the next one and so on...
http://3s.gonzoinc.com/albums/userpi...2/IMG_1024.JPG
PM me for Paypal info.
pm sent
I may have to get a set of these once my engine is running again. Might be able to find a source for brand new ones as well and hopefully the pins to go with. Just a quick note....its best to never solder onto an engine harness. Solder is brittle and the connection can fail due to vibrations. Harness repairs are best made with crimped connections, completed with shrink tubing. :)
Payment sent. Shipping address PM to you.
I soldered mine on a couple years ago and haven't had any issues. I also redid my entire harness with tape and Loom so it's all nice and neat.
I found brand new ones a couple years ago and they wanted like $7-8 each with the tails and then add shipping. I couldn't justify the cost. I always made a note going to the junk yard to grab ones I found. We packed up most of the house months ago and I lost track of where everything went. I finally found these going there all my crap...LOL The used ones I have are in great condition. I make sure none of the wires are brittle like our stock ones get after years of heat.
Pp sent!Quote:
Originally Posted by DrGonzo
Sent from the Man Cave!
3 more sets left!!
Coop and Steve, I'll try to get yours out in the mail tomorrow. If not it won't be till Tuesday till I can get them shipped out.
Thank you
Post via Tapatalk
In case you sell out and people are still wanting some quick disconnect plugs you can get some nice ones at http://www.spoolinup.com. That's where I ordered my easy squeeze injector clips. I definitely won't go back to stock clips and metal retainers. Mine were getting brittle with age and heat.
Yeah same here. I hated those clips and most of mine were broken. I had the rear bank clips zip-tied to the injector to ensure they wouldn't come disconnected while driving!!!Quote:
Originally Posted by TurboSinceBirth
I looked at those before and almost went that route but some of my wires going into the injector clips themselves were brittle and the insulation was cracking. So I couldn't go the route of unpinning them. I needed to replace the wires also.
Only 2 more sets available now!!!
I don't doubt that at all. I was just saying its good practice to avoid soldering if possible. Something I've learned about mil-spec motorsport harnesses ;)Quote:
Originally Posted by DrGonzo
What would you recommend?Quote:
Originally Posted by akotten
What is bad about soldering it?
I used to be a mechanic in the Military "ARMY" and the MIL-Spec harnesses on every vehicle from the Humvee to the M1A-1 Abrams had solder points. Usually the common ground points. They had crimp terminals to hold the wires together and then soldered over them.Quote:
Originally Posted by akotten
There is nothing wrong with soldering, stock harness has tons of solder points in it already.
BTW - Only One set left!!
Oops, Looks like I have 2 sets left still.
FeaRpb - Dropping your off to ship out now. Will be mailed regular mail. You should have it by Wends-Thurs
Coop - Waiting on shipping address.
Oops, sent...
Got it Coop.
Tried to get them mailed out but UPS store was already closed...ARGH.
I will try to get them out tomorrow but playing Golf in the morning so if we get done it time I'll get them shipped out. if not it will have to wait till Tuesday, Sorry!
no worries, I have plenty to do, and it's not much to pull the plenum if I so need to...
I'll take the last set!
Having the pigtails definitely makes it easier due to the age of our cars. I have a big spool of automotive TXL wire left over from making my clone ecu adapter harness so I planned to use that if I needed it. Honestly, I haven't gotten around to installing them yet but I really need to. Two of my injector clips are cracked/missing partial pieces.Quote:
Originally Posted by DrGonzo
so there is one set left!?! if so ill take it!
Yep there is one set left. PM me for Paypal.Quote:
Originally Posted by jeremyr
Payment, received and shipping out on Tuesday.Quote:
Originally Posted by CGSTEALTH1791
For everyone else that has paid, I did not make it to the UPS store in time like I hoped. Golfing went longer than expected this morning...LOL They will all ship out on Tuesday as that will be the next time I'm at the post office.
all gone? what are these off of?