What did you do today to your 3/S?

uhh haughh.. i thorough out my back.. not really but she is hurtin' a little.

anywho. i continued working on my wheel. just taping for now, which was a close second in aggravation to sanding.. anywho, i'm at least 70 percent through taping off for the inside's coat. so here are a few pics..

http://i144.photobucket.com/albums/r...s/S5002893.jpg

http://i144.photobucket.com/albums/r...s/S5002899.jpg

any suggestions for this wheel? things to make it look more professionally done?,

tired, DONE

_isiah

Walked right past it, turned around, scrapped some bird shit off, and got in my corolla to go to work.

Installed CFDS today!!!

Installed Megan M2 Exhaust on Yoshi's VR-4 and fixed 3sx's crappy job of wiring in the fuel pump hotwire on his car.

Some idiot at 3sx ran the 12+ feet of main power to the fuel pump relay on the outside of the car!!! WTFH!! Top it all off they ran it inside the shroud that encases the damn fuel lines! Yeah real smart!!! Run a hot power wire next to a fuel source. I don't care if the damn thing was fused it would only take one spark to set the fuel up in an accident! Considering they had like a 60amp fuse it would have sparked before it blew the fuse.....

Quality work right there! Yoshi didn't even know they had done this. If I hadn't installed his exhaust it would have been left un-noticed.

Power wire is now safely routed inside the car where it should be.

Quote:

---

Originally Posted by DrGonzo

Installed Megan M2 Exhaust on Yoshi's VR-4 and fixed 3sx's crappy job of wiring in the fuel pump hotwire on his car.

Some idiot at 3sx ran the 12+ feet of main power to the fuel pump relay on the outside of the car!!! WTFH!! Top it all off they ran it inside the shroud that encases the damn fuel lines! Yeah real smart!!! Run a hot power wire next to a fuel source. I don't care if the damn thing was fused it would only take one spark to set the fuel up in an accident! Considering they had like a 60amp fuse it would have sparked before it blew the fuse.....

Quality work right there! Yoshi didn't even know they had done this. If I hadn't installed his exhaust it would have been left un-noticed.

Power wire is now safely routed inside the car where it should be.

---

what is the issue? Sounds like the wire was properly installed.

sound clip of exhaust.

Quote:

---

Originally Posted by 2fnloud

what is the issue? Sounds like the wire was properly installed.

---

You never run a power wire on the outside of a car. You want to shield it from the Environment, Heat, Bottoming out, Road debris, ETC. You also never run an exposed power wire and zip tie it to a pressurized fuel line unless you want to blow the car up if you get in an accident!!

BS it is the fumes that are explosive. You might as well thell the thousands that run 5-10 runs of 0/1 GA from the hood to the trunk that that are going to blow themselves up. :rollseyes:

Quote:

---

Originally Posted by shmoo

uhh haughh.. i thorough out my back.. not really but she is hurtin' a little.

anywho. i continued working on my wheel. just taping for now, which was a close second in aggravation to sanding.. anywho, i'm at least 70 percent through taping off for the inside's coat. so here are a few pics..

http://i144.photobucket.com/albums/r...s/S5002893.jpg

http://i144.photobucket.com/albums/r...s/S5002899.jpg

any suggestions for this wheel? things to make it look more professionally done?,

tired, DONE

_isiah

---

I really hope those aren't the wheels off your car! If so there will be an intervention next NG to get your ass off crack!

What exactly are you doing to those wheels?