OLED inside air vent adapter.
https://i.imgur.com/7U0jWns.jpg
OLED vs LCD screen physical size comparison:
https://i.imgur.com/cLusvrI.jpg?1
https://i.imgur.com/CZNBX6q.jpg
Printable View
OLED inside air vent adapter.
https://i.imgur.com/7U0jWns.jpg
OLED vs LCD screen physical size comparison:
https://i.imgur.com/cLusvrI.jpg?1
https://i.imgur.com/CZNBX6q.jpg
I am certain I will need a new brain to use OLED but I'm loving the yellow.
Okay let me know when you're ready.Quote:
Originally Posted by BlackStealth
By the way do you have any more screenshots of how the information is presented on the 4x20 display?
Sorry, I didn't take any other screen shots. I've combined screens into 4 lines where I could. I haven't modified the main menu to 4 lines yet -- I plan to display external sensor data on there, as I think that is what people would want.
More information per screen so there is less need for scrolling would be awesome. Like both front and rear trims on the same screen and all 4 senors on another screen.
Exactly, and by the way, what you've suggested I've already combined also.Quote:
Originally Posted by Unlogic
That sounds great!
Would it be possible to replace the power regulator in older units with at beefier one to avoid having a separate power cable for the OLED display?
The good news is the linear voltage regulator inside your LCDBC unit can provide the necessary power, it's just a question whether or not the heat sink is adequate.Quote:
Originally Posted by Unlogic
Is this the dual regulator version that supports the OLED display or should I be looking for a bigger heat sink?
http://pics.unlogic.se/3000gt/projek...315_204218.jpg
Your purple boxed LCDBC shows 1 voltage regulator with a heatsink, and 1 power transistor for boost solenoid.
I already have a solution for older LCDBC units. Because the OLED requires an adapter to convert 20 pins to a 4 pin wire harness, this is a good place to include a low profile voltage regulator -- problem solved.
https://i.imgur.com/p1HGu0A.jpg
Quick question...Can I flash the LCDBC AEM v4.00 Firmware to the 2020 version with the OLED screen. Will it work? I only found a flash for the OLED for the LCDBC+Addon.
I haven't released any OLED versions yet for the "AEM type software". Which OLED screen size do you have? 4x20 or 2x16?
I have the 4x20 versionQuote:
Originally Posted by BlackStealth
A few weeks ago I started working on the 2x16 OLED/AEM version -- I'll finish that project and then convert it for 4x20 OLED.
Those that are running AEM ECUs and want to use OLED display on their units, both 4x20 and 2x16 is supported.
http://lcdbc.xp3.biz/updates/AEMUpdate401.zip
Thank you for the Update!! Works great!Quote:
Originally Posted by BlackStealth
Glad to hear that. When switching over to "AEM version", you will need to go to config menu and look for "Reset Customs Y/N". This will get rid of all the funny characters, and replace them with the word Custom001, Custom002, etc.Quote:
Originally Posted by JFC3000GT
Anyone with older LCDBC (version 3.0 or higher firmware) can now swap out their LCD screen for newer technology such as an OLED screen. These displays have fast screen refresh even during cold weather operation. Also it now uses 4 wires instead of 12 wires, making installation a little easier / lighter.
https://i.imgur.com/swstv4I.png
All purchase inquiries should be sent this thread here:
https://www.3sgto.org/threads/17430-...-time-ECU-data