So who wants their ECU's "Chromed"?

Yes that is correct, I did make a mistake. Based on earlier messages VR4whore had sent me privately and info he posted here, I was too quick to point the cause of his stumbling at boost because the way he had described it earlier sounded right about the point where the fuel relay normally switches from low voltage to full voltage. I did not verify how the stock low/high voltage fuel relay operated with a non-VR4 ECU and was very concerned he might be running very lean based upon symptoms. I was surprised to hear the our cars default to high voltage mode, but when you think about it, it makes sense from the point of safety / failure mode point of view. I have verified the fuel relay circuit in my service manual and what you have said is correct. My apologies. It's very difficult to give tuning advice without being there in person.

Quote:

---

Originally Posted by BlackStealth

Yes that is correct, I did make a mistake. Based on earlier messages VR4whore had sent me privately and info he posted here, I was too quick to point the cause of his stumbling at boost because the way he had described it earlier sounded right about the point where the fuel relay normally switches from low voltage to full voltage. I did not verify how the stock low/high voltage fuel relay operated with a non-VR4 ECU and was very concerned he might be running very lean based upon symptoms. I was surprised to hear the our cars default to high voltage mode, but when you think about it, it makes sense from the point of safety / failure mode point of view. I have verified the fuel relay circuit in my service manual and what you have said is correct. My apologies. It's very difficult to give tuning advice without being there in person.

---

Its also incredible difficult to give trouble shooting advice without being present. Sometimes the way someone is checking a system is flawed. But hey free advice is worth the price. :)

Quote:

---

Originally Posted by BlackStealth

It's very difficult to give tuning advice without being there in person.

---

I hear that!

Quote:

---

Originally Posted by Greg E

If you guys open up your 23861xx6 XML, replace the periphery tables with this:

Code:

---

        <table name="ECU Periphery0 Bits (272) +0" category="Periphery" address="10272" type="2D" scaling="EnableDisableBit">
                <table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
                        <data>bit.15                                              .</data>
                        <data>bit.14  O2 Heater Functions                          .</data>
                        <data>bit.13                                              .</data>
                        <data>bit.12  Purge function                              .</data>
                        <data>bit.11  EGR function                                .</data>
                        <data>bit.10  Timing Retard on Accel                      .</data>
                        <data>bit.09  Cat Warmup Ign Retard Function  (Leave OFF)  .</data>
                        <data>bit.08                                              .</data>
                        <data>bit.07  Knock Sensor/Octane Functions                .</data>
                        <data>bit.06  Speed Limit Function                        .</data>
                        <data>bit.05                                              .</data>
                        <data>bit.04  Closed Loop function                        .</data>
                        <data>bit.03                                              .</data>
                        <data>bit.02  OBD2 Bytes A and C                          .</data>
                        <data>bit.01  OBD2 Bytes B and D                          .</data>
                        <data>bit.00                                              .</data>
                </table>
        </table>

        <table name="ECU Periphery1 Chrome Mods Bits*" category="Periphery" address="10282" type="2D" scaling="EnableDisableBit">
                <table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
                        <data>bit.15                                              .</data>
                        <data>bit.14                                              .</data>
                        <data>bit.13                                              .</data>
                        <data>bit.12                                              .</data>
                        <data>bit.11                                              .</data>
                        <data>bit.10                                              .</data>
                        <data>bit.09                                              .</data>
                        <data>bit.08                                              .</data>
                        <data>bit.07                                              .</data>
                        <data>bit.06                                              .</data>
                        <data>bit.05                                              .</data>
                        <data>bit.04                                              .</data>
                        <data>bit.03                                              .</data>
                        <data>bit.02                                              .</data>
                        <data>bit.01                                              .</data>
                        <data>bit.00  Chrome Mod Lean Spool                        .</data>
                </table>
        </table>

        <table name="ECU Periphery2 Bits (292) +0" category="Periphery" address="10292" type="2D" scaling="EnableDisableBit">
                <table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
                        <data>bit.15 P0443 P0446 P0403 P1104 P1105 Solenoids Test  .</data>
                        <data>bit.14 P0450 Fuel Tank Pressure Sensor Test          .</data>
                        <data>bit.13 P0442 Evap Incorrect Purge Flow Test          .</data>
                        <data>bit.12                                              .</data>
                        <data>bit.11 P0135 P0141 P0155 P0161 O2 Heater Test        .</data>
                        <data>bit.10 P1400 MAP Sensor Test                        .</data>
                        <data>bit.09 P0403 EGR Solenoid Test                      .</data>
                        <data>bit.08 P0505 Idle Control System Test                .</data>
                        <data>bit.07 P0170 P0173 Front Rear Fuel Trim Test        .</data>
                        <data>bit.06 P0125 Excessive Time to Enter Closed Loop    .</data>
                        <data>bit.05 P030x Misfire Detected (set with bit 4)      .</data>
                        <data>bit.04 P030x Misfire Detected (set with bit 5)      .</data>
                        <data>bit.03 P0136 P0156 Front Rear Secondary O2 Sensor    .</data>
                        <data>bit.02 P0130 P0150 Front Rear Primary O2 Sensor      .</data>
                        <data>bit.01 P0421 P0431 Warmup Pre-cats Efficency Low    .</data>
                        <data>bit.00 ALL OBD2 DTC Lookups                          .</data>
                </table>
        </table>

        <table name="ECU Periphery3 Bits (2A2) +0" category="Periphery" address="102a2" type="2D" scaling="EnableDisableBit">
                <table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
                        <data>bit.15                                              .</data>
                        <data>bit.14                                              .</data>
                        <data>bit.13                                              .</data>
                        <data>bit.12                                              .</data>
                        <data>bit.11                                              .</data>
                        <data>bit.10                                              .</data>
                        <data>bit.09                                              .</data>
                        <data>bit.08                                              .</data>
                        <data>bit.07  P0551 Power Steering Pressure Sensor Circuit .</data>
                        <data>bit.06  P0500 Vehicle Speed Sensor Malfunction      .</data>
                        <data>bit.05                                              .</data>
                        <data>bit.04                                              .</data>
                        <data>bit.03                                              .</data>
                        <data>bit.02  P1103 WasteGate Actuator Malfunction        .</data>
                        <data>bit.01  P0510 Closed Throttle Position Switch        .</data>
                        <data>bit.00  P1600 Battery Voltage Low                    .</data>
                </table>
        </table>

---

These are the correctly mapped bits. :)

---

I have a dumb question how do you do this? I opened ecuflash right clicked periphery and new map then this window opened and I have no clue what to put where.

Quote:

---

Originally Posted by fridayda13th

I have a dumb question how do you do this? I opened ecuflash right clicked periphery and new map then this window opened and I have no clue what to put where.

---

The following are general guidelines. This is the way you would do this in XP, but Vista / 7 might have slightly different terminilogy.

You have to browse to that directory in "My Computer" then right click on the file and select "Open With" . . . then select "Choose Program" and finally select notepad as your editor of choice. Then click "Ok" and notepad should open the xml file allowing you to copy and paste the above info. It is not required to check the "Always use the selected program to open this kind of file" check box.

Ohhhh ok thank you. Yeah that doesn't work for windows 7 when I open it, it just looks like a bunch of weird letters

Sounds like you are trying to open the wrong file. The file you want should be in the rommetadata folder.

The scaling is messed up for those table you sent out. I switched the scaling back to blobbits and it worked fine. BUt if I left the EnableDisableBits it didn't work. Can you post the scaling info to put in the scaling section?

I need to get back to playing with my setup...too much time in other things.

Quote:

---

Originally Posted by Jesters Deadd

The scaling is messed up for those table you sent out. I switched the scaling back to blobbits and it worked fine. BUt if I left the EnableDisableBits it didn't work. Can you post the scaling info to put in the scaling section?

---

Yep I did...

I'll put it up tonight when I get home.