Shoul I buy these parts for DR750 daily driver?

Printable View

11-30-2013, 11:22 AM
SoarnBy

Shoul I buy these parts for DR750 daily driver?

I will be daily driving my car and never tracking it nor launching my car. 99% of the time pump gas 1% E85 My power goals are 450ish awhp on pump gas and 550ish on e85.

Should I buy these additional parts to my build? IPS Motorsports will be doing my build. Ray has given me the setup.

300m output shaft
2 piece carbon fiber drive shaft

Here is a list of the current parts that are going on my 95 VR4 Spyder.

Greddy OLED Boost controller- installed already
DR750 - New Version and ported
1000CC Dynamic Plug and Play fuel injectors
Spark Plugs NGK Copper BKR7E-1 Spark Plugs gaped to .025
Walbro 416 E85 Fuel Pump with install kit/hotwire kit
RPS 6 puck max series clutch and a resurfaced flywheel
MAF 3.75
AEM Series 1 or 2 - not sure which IPS wants me to get
Intercooling Piping Stock
DrWelds upgraded wastegates
Bell House Brace
BOV

60K maintenance kit –

* OEM Water Pump with gasket and oring
* OEM Timing Belt Hydraulic Tensioner
* OEM Timing Belt Tensioner Pulley
* OEM Timing Belt Idler Pulley
* OEM Timing Belt
11-30-2013, 12:59 PM
Jimvr4

Alan, please make this guy post up ONE thread for his build and not 100+ threads with every possible title imagineable.
11-30-2013, 02:41 PM
TurboSinceBirth

Nope. Ray uses the stock OS and it works fine. You will need a billet endcase for your 6-speed though. I'd only upgrade the driveshaft if your carrier bearings are shot; otherwise, that money will go further elsewhere. You'll want to add an HKS DLI to the list, ditch the MAF since you can run speed density with AEM and IPS will prefer tuning it with this, upgrade the fuel rail loop to an aluminum one for peace of mind even though Ray saw different F&R fuel trims at 600AWHP on E85, get some upgraded motor mounts, downpipe, gutted precats, a wideband, and I'm sure some other things I'm forgetting.
11-30-2013, 05:32 PM
Ange

Other than what Turbosincebirth said I would upgrade intercooler+piping and preferably a larger plenum and tb to let those dr750 flow as they should.
11-30-2013, 06:11 PM
CoopKill

Nothing on your "Should I buy" list is needed. With your stated intended use you seem to have all the power needs covered, but for the inter-cooler.
11-30-2013, 06:27 PM
Greg E

Quote:

Originally Posted by Jimvr4

Alan, please make this guy post up ONE thread for his build and not 100+ threads with every possible title imagineable.

What if he lists DR750s in the title? Would that technically make it a new thread each time?
11-30-2013, 09:18 PM
J. Fast

Quote:

Originally Posted by TurboSinceBirth

Nope. Ray uses the stock OS and it works fine. You will need a billet endcase for your 6-speed though. I'd only upgrade the driveshaft if your carrier bearings are shot; otherwise, that money will go further elsewhere. You'll want to add an HKS DLI to the list, ditch the MAF since you can run speed density with AEM and IPS will prefer tuning it with this, upgrade the fuel rail loop to an aluminum one for peace of mind even though Ray saw different F&R fuel trims at 600AWHP on E85, get some upgraded motor mounts, downpipe, gutted precats, a wideband, and I'm sure some other things I'm forgetting.

1) Aluminum rail feeds are not longterm compatible with high ethanol percentage fuels. 2) 550whp isn't even close to the "you need this" billet end cover... When you get some results of your own you'll know better.