View Full Version : Custom Trunk Sub Enclosure
n2nsanity
09-20-2012, 01:26 PM
Here's what I'm hoping to do. If anyone sells something like this, please send a link, I'll probably just buy it. I'm sure someone has made something at least similar to this. Any help with this project (pictures, dimensions, diagrams) would be greatly appreciated.
So here's the plan. I want a single 10" non-ported enclosure for my JL Audio 10w3. I want it to fit directly behind the seats (where the floor recesses) going up to the top back edge of the seats, making the most efficient use of that space. I'd like the sub on the driver side and an area for mounting amp, capacitor, etc on the passenger side. Maybe with a plexiglass covering over the amp/capacitor area. Maybe some type of bandpass enclosure for the sub so I don't have to worry about it hitting the seats or getting damaged by anything loose in the trunk. Or maybe something really discreet that will blend in with the trunk interior and be less of a target for theft.
Let's see some pics of anything like this.
I'll bet, if you take some measurements of the available space behind the seat, that 2fnloud could plug those into his box-prog and give you some good input.
ictponder
09-20-2012, 04:18 PM
<-Works at a 12v shop. I can try and take a few minutes and get some measurements to input into our program.
n2nsanity
09-20-2012, 05:38 PM
Thanks :)
MeTarzan
09-20-2012, 10:39 PM
I did one a while ago for my JL 15. I did it in 2 parts...the actual box to size and then a cover piece to blend into the interior of the car. I even made a small panel to go down between the box and the rear cover so I wouldn't have things flying up out of the trunk area if there were smaller things back there
http://memimage.cardomain.com/ride_images/1/832/621/2077810021_large.jpg?modal
http://memimage.cardomain.com/ride_images/1/832/621/2077810023_large.jpg?modal
n2nsanity
09-21-2012, 03:43 AM
I did one a while ago for my JL 15. I did it in 2 parts...the actual box to size and then a cover piece to blend into the interior of the car. I even made a small panel to go down between the box and the rear cover so I wouldn't have things flying up out of the trunk area if there were smaller things back there
http://memimage.cardomain.com/ride_images/1/832/621/2077810023_large.jpg?modal
Nice work. Although nothing discreet about that lol. I definitely plan on keeping my rear seats.
I also hope to mend the original 6x9 enclosures to hold 8's. But that's for another day.
MeTarzan
09-21-2012, 04:41 AM
Nice work. Although nothing discreet about that lol. I definitely plan on keeping my rear seats.
I also hope to mend the original 6x9 enclosures to hold 8's. But that's for another day.
Very true...car has tint on it so its hard to see from the outside. When I first put this in my car I had the amp mounted to front so you could see it between the seats and was living in pittsburgh pa at the time and actually they broke in a stole the amp :( . Now all that is hidden under the cover.
2fnloud
09-21-2012, 09:27 AM
You will be hard pressed to get an 8 in that 6x9 enclosure, depth will be you limiting factor
2fnloud
09-21-2012, 09:31 AM
a shallow 8 would work, but why rear? you have the sub. I would try to get a 8 in the door, paired with a proper 2" midrange...add a tweeter in the A-pillar. Make a kick butt front stage.
MeTarzan
09-21-2012, 09:57 AM
I defiantly wouldn't put an 8 in place of the 6x9s I would replace them with some better comp though
2fnloud
09-21-2012, 09:59 AM
with a sub in the mix, I wouldn't waste weight, money, or time concerning with rear speakers, unless you are designing a mobile theater system.
n2nsanity
09-22-2012, 11:49 AM
a shallow 8 would work, but why rear? you have the sub. I would try to get a 8 in the door, paired with a proper 2" midrange...add a tweeter in the A-pillar. Make a kick butt front stage.
The original idea was to have the 8's and some tweeters in place of the 6x9's so there would be no wasted space, minimal added weight, a little bit of bass, completely hidden and harder to steal. I cheaped out and threw them in a box for now. But the bass isn't quite enough. But, I'm sure a good single 10 will be plenty for me as it always has been in the past.
You make a good point about just having the single sub and trying 8's in the door instead. Fitting 8's in the door actually sounds more challenging to me, but at least the depth is there. My 6x9's (rockford fosgate power series) don't even fit in the rear enclosures. Had to add spacers and cut out some material from the rear panels. But all this is for later. For now I want to work on a nice custom setup for my 10 and the amp. I thought you would have some suggestions for this.
2fnloud
09-22-2012, 12:53 PM
ICTPonder mentioned he would do it, so I did not want to duplicate the effort. Other than to add I would have there sub centered and pointing backwards.
CoopKill
09-22-2012, 03:17 PM
Mixing sub sizes I thought is not a good idea. At least the 10"/12", and the 10"/15" combo I have heard was crap....
2fnloud
09-22-2012, 04:32 PM
Coop, you are right. it is not a good idea. with the design of a hatchback car, it is easy to get load bass from subwoofer(s). Enough to drown out the sound from any speaker in the rear.
Properly sound deadened doors, a kick butt front stage...and you have a killer sound system.
n2nsanity
09-23-2012, 03:40 AM
hmmm, some things to think about. the RF 6x9's are pretty loud and weren't too cheap. I'll rock them for a while. I may try the 8's in the door, but I really don't think there's room in diameter and they will probably be hitting the door panel. Sound deadener is also on the list. Any good recommendations for that? I have some 3m rubberized undercoating spray. What's something decent but affordable if my 3m stuff won't work?
I still want to try the 8's in the rear panels one day. Just out of curiosity and to try something different. But aside from getting this 10 installed, I've got plenty other projects to worry about, particularly my tt conversion :)
2fnloud
09-23-2012, 08:55 AM
For sound deadening I recommend reading info here. (http://www.sounddeadenershowdown.com/cgi-bin/index.cgi)
And I would let go of the 8" in the door idea. Your 10" sub woofer (or any other sub woofer you end up with) will more than cover the low end that you are wanting to achieve.
hdorre
09-23-2012, 11:17 AM
Sound deadener is also on the list. Any good recommendations for that?
The good brands are AudioTechnix and Second Skin Audio and Sound Deadener Showdown.
2fnloud
09-23-2012, 12:11 PM
The good brands are AudioTechnix and Second Skin Audio and Sound Deadener Showdown.
The link I referenced goes to the sound deadener showdown web site.
hdorre
09-23-2012, 12:45 PM
The link I referenced goes to the sound deadener showdown web site.
Yeah, I saw. I was just giving the OP other options :) If I didnt include SDS in my list, then the OP may think I omitted it for a reason.
ictponder
09-23-2012, 10:02 PM
This should be here tomorrow. Going to get started making a single enclosure. I will keep the OP updated.
Alpine 8" R-Type Subwoofer (http://alpine-usa.com/product/view/swr-843d)
http://alpine-usa.com/data/product_images/499_1lg.jpg
2fnloud
09-23-2012, 10:18 PM
IF my T/B subs blow, I am so getting four of these from you Issac, can you PM me cost?
ictponder
09-23-2012, 10:38 PM
sure can, might be able to get a better discount for getting 4 but I'll have to call the Alpine rep tomorrow. I'm also getting the PXA-H100 delivered tomorrow to replace the PXE-H650 so now I will be able to tune the processor directly from the HU instead of the PC.
ictponder
09-29-2012, 09:30 PM
...started building the box today, will have some pics before the weekend is over.
n2nsanity
09-30-2012, 04:47 AM
Nice :) If you have some good blueprints, that would be awesome. I'm still brainstorming on how to build mine. I need to get it drawn out.
ictponder
10-01-2012, 01:11 AM
Progress so far.
https://xpo00g.bay.livefilestore.com/y1psA6MHCSJuNS4GQ7w6apzB4qbc9fYoX7EdGFEsJdWYeZosxq OzJIh0BXiyNByqR4XSlP_vSiZHM-C_h4By0yJTsc7F8brbSO5/2012-09-30_16-52-16_572.jpg?psid=1
https://xpo00g.bay.livefilestore.com/y1patCa0BdfvEYJvHgEn1G-_kNdCLU49_cDxXWvO0o7LS4byhTwk9h9na9GX5qdz2m5L2_mno k4xWuVwDiEuR3TUYnVrhTlWxMg/2012-09-30_17-44-25_534.jpg?psid=1
https://xpo00g.bay.livefilestore.com/y1ptSDBH0v6QxxFD_jqGZSyeDRv1F4NhIVKZvrEQWpkmld6gHo 6n27Jx1sv2GCVTV86rBft-2ukP6J9ncQ_EY_WN5NMhivsHviu/2012-09-30_17-44-44_503.jpg?psid=1
https://xpo00g.bay.livefilestore.com/y1pQqMTwc0GBeyN3gv04JG_LWq29aRN9Da2gJpg14zeu7kqnb4 X5q3oUyq1VaGtQkgbJzo0Nc9qyUT1kKWaAdi-kRgE_wr6Brh7/2012-09-30_17-45-13_706%201.jpg?psid=1
n2nsanity
10-01-2012, 02:37 PM
Looking pretty good man. That's the layout I was going for. Looks like you had the same issue I did with my current box. The floor is uneven, so I didn't get a good measurement and it was tight at the top. I also wanted to keep it slightly more behind the plastic trunk panels and angled up top to match the top lip on the seats. This would be mostly for the ability to mount the sub a little higher up, but probably not worth the hassle to add that extra angle into the mix. Hard to tell if yours has this angle from the pics.
For some reason I thought I could pull this off with just a tape measure, pen and paper... forgetting I haven't done geometry in 15 years, lol. I got frustrated and just threw together a quick shallow rectangular box.
I think doing something with the trunk floor cover bracket might help with the fitment a lot. I would definitely mount it to the floor from inside the box. I'd be more pissed about someone stealing the enclosure than the sub :p
These would definitely be worth selling. Or at least a kit with the precut pieces.
n2nsanity
10-01-2012, 03:52 PM
This is the best I could come with so far, lol. It's pretty awful. It would probably be easier to fiberglass the thing.
http://i49.tinypic.com/oic85h.jpg
CoopKill
10-01-2012, 04:35 PM
So for what I was planning I want to have the subs (10's non-ported) in each rear corner at an apprx. 30* angle to the center, and tilted toward the front.
Question to the Audiophiles: What are the effects of placement for what I am planning versus pointing subs to the rear?
CoopKill
10-01-2012, 04:36 PM
Oh, Props on the box! And the cut in the lawn no sweep up technique!
ictponder
10-01-2012, 05:20 PM
Looking pretty good man. That's the layout I was going for. Looks like you had the same issue I did with my current box. The floor is uneven, so I didn't get a good measurement and it was tight at the top. I also wanted to keep it slightly more behind the plastic trunk panels and angled up top to match the top lip on the seats. This would be mostly for the ability to mount the sub a little higher up, but probably not worth the hassle to add that extra angle into the mix. Hard to tell if yours has this angle from the pics.
For some reason I thought I could pull this off with just a tape measure, pen and paper... forgetting I haven't done geometry in 15 years, lol. I got frustrated and just threw together a quick shallow rectangular box.
I think doing something with the trunk floor cover bracket might help with the fitment a lot. I would definitely mount it to the floor from inside the box. I'd be more pissed about someone stealing the enclosure than the sub :p
These would definitely be worth selling. Or at least a kit with the precut pieces.
I left the top edge flat for 2 reasons: 1. easier 2. slightly more airspace
The front piece is angled to match the strut cover face. I left it back in order to build a false front for the amp and subwoofer excursion. The box will be attached to the seat hooks using a custom steel bracket, which will allow you to simply remove the 4 screws, slide the box in place, and re-attach the hooks and plastic covers over the metal bracket. Not sure if I'm going to use vinyl or carpet at this point. I bought enough wood to build a template as I go in order to build more if anyone is interested.
n2nsanity
10-01-2012, 05:56 PM
I can't even figure out my dimensions on paper, lol. Dunno how I will actually make the cuts.
With 10's it's hard to have room for them facing the rear without hitting the floor. With 12's it might be impossible. These are some of the things I was taking into consideration.
I also thought about a few different mounting options. With single and dual 10's or 12's. Then there were also those custom "stealth boxes" I think they were called. They make pretty efficient use of the rear corners. I didn't want to use this as I use those storage bins often. You should see how much "just in case" stuff I have crammed in there, lol.
ictponder
10-02-2012, 12:07 AM
I can't even figure out my dimensions on paper, lol. Dunno how I will actually make the cuts.
With 10's it's hard to have room for them facing the rear without hitting the floor. With 12's it might be impossible. These are some of the things I was taking into consideration.
I also thought about a few different mounting options. With single and dual 10's or 12's. Then there were also those custom "stealth boxes" I think they were called. They make pretty efficient use of the rear corners. I didn't want to use this as I use those storage bins often. You should see how much "just in case" stuff I have crammed in there, lol.
The only way I can see 10's fitting in the spot I'm working with is a sealed box + modifying the hinge that holds the spare tire cover so that it sits further away from the back seats, allowing for the enclosure to extend into the hatch area, covering the strut brace completely.
Streamln1
10-02-2012, 12:24 AM
Not a lot of room to work with in there, I don't remember how much room from the top of the strut brace to the underside of the rear seat/cargo cover. The single 8 is really the ideal setup.
Looks good btw.
Streamln1
10-02-2012, 12:38 AM
So for what I was planning I want to have the subs (10's non-ported) in each rear corner at an apprx. 30* angle to the center, and tilted toward the front.
Question to the Audiophiles: What are the effects of placement for what I am planning versus pointing subs to the rear?
Facing subs backwards or towards the hatch make them play louder and have more gain because of 2 things, wavelength and reinforcement. Basically wavelength is because the sub is playing as if its at a greater distance from you, bass notes travel towards the hatch and then forward. This also helps because certain frequencys will reinforce each other, of course certain frequencys will likely sound worse if stuff is rattling and losing energy. Facing them forward will not be as loud but will likely sound more clean, less obstructions between the listener and the speaker, less likelyhood of cancellation.
n2nsanity
11-17-2012, 09:45 PM
How's the box coming along? I haven't even started messing with mine yet. So busy... :(
n2nsanity
12-07-2012, 03:50 AM
Well, I finished it a few days ago. Here's some pics of the project. I stuck with simple for now.
The sub depth is the one thing I forgot to measure. Back of the box wouldn't quite fit. If not for that protruding part at the bottom of the magnet, it would've been fine. Looks worse, but I only needed 1/8" more clearance.
http://i48.tinypic.com/vxynis.jpg
Fixed the depth issue.
http://i49.tinypic.com/2zdzmuo.jpg
Rubber undercoating spray on the inside. Don't know if this helps or hurts, but thought I'd try it for smoother sound.
Sealed all the corners with liquid nails. Was going to use silicone, but didn't have any and didn't feel like going back out. Sounds great to me, so I'm happy.
http://i46.tinypic.com/35anhh4.jpg
I had some terminals, but they were the pop-in type and I didn't even have the right size hole saw. I came up with the idea to use bolts and washers.
I thought this was a unique idea, but later looking online, a bunch of people actually install and prefer them this way.
http://i48.tinypic.com/34hcb2e.jpg
http://i45.tinypic.com/257q7is.jpg
http://i47.tinypic.com/2pq9p1f.jpg
n2nsanity
12-07-2012, 03:51 AM
Finished
http://i48.tinypic.com/35avzhl.jpg
Side view. Loving how well the terminals worked out.
http://i46.tinypic.com/21lpj47.jpg
All done for now. It looks like the sub would be hitting the floor but it's not. Wish I would have mounted it a half inch higher though.
http://i47.tinypic.com/1670e9w.jpg
I think it looks halfway decent and sounds pretty good. If I turn up the bass at all, I have to open my sunroof a little because it rattles like crazy and sounds like it will break.
It's a sealed box with about 1.5cu ft of volume. Minus whatever the sub takes up, so probably more like 1.4.
Fits behind the seats but I still have to force the rear seats to close. I think it would've fit perfect if mounted the sub about 1/2 inch higher. That bezel is an inch wide and deep and is wedged against the floor support.
I'm thinking about trying to make a ring for it and angling it up. Not sure how to do this but it would help for better fitment.
Not sure I'll attempt anything more complicated like I really wanted to do because I spent way too much time on this simple box. I think I'll just pay someone to make exactly what I want later.
CoopKill
12-07-2012, 01:06 PM
Did you insulate the speak wire connectors in any way from the MDF?
Looks nice man.
2fnloud
12-07-2012, 01:36 PM
Did you insulate the speak wire connectors in any way from the MDF?
Looks nice man.
Bill, MDF is non conducting. He is fine.
n2nsanity
12-07-2012, 08:23 PM
put some liquid nails in the holes :p
didn't think it was necessary especially with the washers, but just because
ictponder
05-02-2013, 10:38 AM
Well finally started working on the box again but didn't get far before dinner was ready. I'm a little less motivated now that I sold my car but it'll get done.
Inside view without the rest of the enclosure.
https://skydrive.live.com/redir?resid=903484CCB9BFC425!2201
External port
https://skydrive.live.com/redir?resid=903484CCB9BFC425!2202
Fixed mismatched labels
2fnloud
05-02-2013, 10:47 AM
THAT is shallow
ictponder
05-02-2013, 12:23 PM
Gonna be tuned for that 8" Alpine AND still be able to open the tire access. It's all dry fit atm, still have to make templates in case I need to make more.
CoopKill
05-02-2013, 12:28 PM
That looks to be only about 0.16667ft³ ish... That is not enough for a sealed enclosure, let alone a ported...
n2nsanity
05-02-2013, 01:17 PM
Looking nice. Not sure about size but he said he was tuning it for that specific sub, so I assume he has the math figured out.
ictponder
05-03-2013, 01:40 AM
LOL, I messed up the labels. There is no enclosure yet as it's not 100% put together. https://skydrive.live.com/redir?resid=903484CCB9BFC425!2202 is just the port, located on the back of the enclosure. The other picture - https://skydrive.live.com/redir?resid=903484CCB9BFC425!2201 is the back of the inside of the enclosure. The sub is 4.5" deep so there has to be more to it lol
Not sure why images are not embedding themselves.
CoopKill
05-03-2013, 11:38 AM
NICE! I was wondering what the hell? Gonna be bad ass when done it looks like.
2fnloud
05-03-2013, 12:33 PM
LOL, I messed up the labels. There is no enclosure yet as it's not 100% put together. https://skydrive.live.com/redir?resid=903484CCB9BFC425!2202 is just the port, located on the back of the enclosure. The other picture - https://skydrive.live.com/redir?resid=903484CCB9BFC425!2201 is the back of the inside of the enclosure. The sub is 4.5" deep so there has to be more to it lol
Not sure why images are not embedding themselves.
https://public.blu.livefilestore.com/y2pEeDx28Tf7fXf-Ez3VXGuF_od0ygCLDnZJa7hIy-gnMg4LTec8UkhuNV0GjzULJJyKxyuYHwzlt0uHiy77MK2r2dOp 9QiN1nwlZzKa5AXSQM/WP_20130430_007%20(1).jpg?psid=1
Because fail, the steps that I needed to do to get the info needed to do that was way too complex, photobuck way WAY easier.
ictponder
05-03-2013, 02:26 PM
It seemed to work not that long ago, glad to have you around :D
ictponder
06-05-2013, 01:19 PM
The remaining pieces were accidentally burned in a recreational fire :/ Unfortunately I do not have a spare 3s sitting around anymore to measure lol.
Sure would like a look at the pics...:huh:
ictponder
06-10-2013, 03:33 PM
https://c3c51g.blu.livefilestore.com/y2pSc64MnpzuwjU82ekVVIIFFOK3stX9yX5RNL57jSyoJ8Xg4g cEj4rPes1TYLgrnpU8YEY0yV82YrOW3i0eE_FMoeC8IysreFSg TkwFnzhhpXAsCwTM5tM4P3wgBpp6Kdi/WP_20130430_006%20(1).jpg?psid=1
https://chc51g.blu.livefilestore.com/y2p_lW1K8OkDURLWrgv3J0b3aujAkhub-CwEeupA-u8kGysARd-VdT_P20SRzFVZGvQJBgRrZWeMVspOgry4wxiZtsSAgL4NJK_Cg Ev-bqSLlkgULI0FjkNFl9WperufQPt/WP_20130430_007%20(1).jpg?psid=1
I had 4 other pieces that formed the front of the actual box where the sub mounted but...
https://c3c51g.blu.livefilestore.com/y2pSc64MnpzuwjU82ekVVIIFFOK3stX9yX5RNL57jSyoJ8Xg4g cEj4rPes1TYLgrnpU8YEY0yV82YrOW3i0eE_FMoeC8IysreFSg TkwFnzhhpXAsCwTM5tM4P3wgBpp6Kdi/WP_20130430_006%20(1).jpg?psid=1
https://chc51g.blu.livefilestore.com/y2p_lW1K8OkDURLWrgv3J0b3aujAkhub-CwEeupA-u8kGysARd-VdT_P20SRzFVZGvQJBgRrZWeMVspOgry4wxiZtsSAgL4NJK_Cg Ev-bqSLlkgULI0FjkNFl9WperufQPt/WP_20130430_007%20(1).jpg?psid=1
I had 4 other pieces that formed the front of the actual box where the sub mounted but...
Damn my luck, Isaac.
Something like that raises lots of possibilities...:sad:
ictponder
06-12-2013, 12:36 AM
Yeah, I'm bummed because the 2 inner side pieces were compound angles both ways. The whole thing (if completed) will simply slide between the spare tire floor and the back seat, allowing full access to the spare and use the seat hooks on the side to secure the box to the car.
Yeah, I'm bummed because the 2 inner side pieces were compound angles both ways. The whole thing (if completed) will simply slide between the spare tire floor and the back seat, allowing full access to the spare and use the seat hooks on the side to secure the box to the car.
Damn, damn, damn...:sad:
sketch
07-18-2013, 03:55 PM
bump.
any update(s)?
ictponder
07-19-2013, 11:09 AM
Not lately. I've got the sub and pieces sitting there just need to get someone with a car for measurements.
2fnloud
07-19-2013, 11:33 AM
How long would you need that car for a day?
ictponder
07-19-2013, 12:03 PM
An hour maybe
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.