PDA

View Full Version : Want to learn to TIG weld



Intropy
07-26-2012, 06:25 PM
I feel like welding is one of the automotive skills I'm missing. I know next to nothing about it.

Where do I start? What equipment do I need?

AdamVR4
07-26-2012, 07:17 PM
Some people just buy a TIG, tank, mask, gloves, rod and dive in (Additional crap you will want: Bench grinder, angle grinder, wire brushes, etc )...

You could take the more conservative approach and take a TIG welding course at the local community college first.

You seem sharp, I bet you can get by with some time in your garage and the internet.

Here's some useful info, the charts at the bottom of the page will get you started: TIG Welding (http://www.stanford.edu/group/prl/documents/html/TIGweld.htm)

More good shit: http://www.ckworldwide.com/technical_specs.pdf

nodoze
07-26-2012, 09:03 PM
, pyou may want to star wih mig welding, its a ton easier will help you get a hang for adjustemtns needing made penetration etc. some people need charts etc to weld, i can do mine all by ear and how the welds look. tig is easy when doing steel gets difficult when doing aluminum. you can make a cheap tig welder out of an old stick welder and save hundreds if you are not up for investing alot right away , but out of the box a stick welder wont have a high frequency start so aluminum welding will be out of the question . but you can scratch start on steele and learn the basics

Granny
07-26-2012, 09:25 PM
We spent a few evening welding in my engine performance class.
It was taught at the votech school.

92pearltt
07-27-2012, 03:56 AM
Its really not hard to learn, but it does take time to perfect. If you have the money just buy a setup and practice at home. Honda-tech (ya I know) has a really good welding/fab section you can learn a lot from. Or as others said you could just take a class at your local tech school.

Chris@Rvengeperformance
07-27-2012, 01:27 PM
I agree that if you have no experience welding then mig welding is the place to start. With a good welder it is like using a hot glue gun.

Intropy
07-27-2012, 03:05 PM
Thanks, I think I'm either going to take a class or get a book and do home learning.

Looking on Amazon, this seems to have received the best reviews:
How to Weld (http://www.amazon.com/How-To-Weld-Motorbooks-Workshop/dp/076033174X/ref=sr_1_2?ie=UTF8&qid=1343412070&sr=8-2&keywords=tig+welding)

Anyone have other reading material recommendations?

AdamVR4
07-27-2012, 04:11 PM
Thanks, I think I'm either going to take a class or get a book and do home learning.

Looking on Amazon, this seems to have received the best reviews:
How to Weld (http://www.amazon.com/How-To-Weld-Motorbooks-Workshop/dp/076033174X/ref=sr_1_2?ie=UTF8&qid=1343412070&sr=8-2&keywords=tig+welding)

Anyone have other reading material recommendations?

That does look like a pretty good book, but it also looks like you'd only be interested in about 30 pages of it.

I don't know the true practical limits of a MIG welder, but I assume the main reason you're interested in a TIG is because of aluminum. Sure, you can use a MIG or oxy-acetylene or whatever else to weld aluminum, but it's not nearly as consistent as with a TIG from what I've seen.

If vast majority of your welding will be steel, get a MIG and be done.

Beyond that, using a MIG is nothing like using a TIG, so don't think that the skills translate. You can teach anyone how to use a MIG in minutes as long as they have a functional finger, but TIG takes a lot more practice and is much more closely related to oxy-acetylene welding.

When I took a course, I started with oxy-fuel and finished that quickly enough to squeeze in a few weeks of TIG lessons. Steel and even stainless steel were quite easy, but I never really got comfortable with aluminum.

Are you on 3ST? You freaking should be if you're not (nvm, I see you're registered but only a public member, sigh). Mark W (Minnesota, 10.1 car) seems to be having good luck with Everlast PowerPro 256 (budget/china TIG). Hard to argue with these first beads from a novice -

http://www.3stech.org/forum/download/file.php?id=27

Intropy
07-27-2012, 04:29 PM
That does look like a pretty good book, but it also looks like you'd only be interested in about 30 pages of it.

Hmm, you're right. Aluminum is obviously what I'm most interested in.


Are you on 3ST? You freaking should be if you're not (nvm, I see you're registered but only a public member, sigh). Mark W (Minnesota, 10.1 car) seems to be having good luck with Everlast PowerPro 256 (budget/china TIG). Hard to argue with these first beads from a novice -

http://www.3stech.org/forum/download/file.php?id=27

Yeah, I'm registered but not "approved" or whatever. Can somebody on there get me approved?

Chris@Rvengeperformance
07-27-2012, 04:29 PM
the mig is not entirely useless for training. If you can get your hand control to where you can make pretty mig or especially stick welds you can have a huge head start. I actually started on stick welding and I'm glad I did. I could run a bead a 6 inches longer or more that the slag would pop off in one piece.

Maximal
07-27-2012, 05:23 PM
TIG's are expensive, especially for a decent one. It might be better to just to pay for a class to learn then buy one once you get it mastered.

Intropy
07-27-2012, 06:15 PM
TIG's are expensive, especially for a decent one. It might be better to just to pay for a class to learn then buy one once you get it mastered.

What's an example of a decent one?

box
07-27-2012, 06:57 PM
Remember if you're wanting to tig aluminium, you'll need an AC/DC welder (most of the cheapies are DC only), so expect to be paying about 1k atleast for just the welder, add to that gas and appropriate equipment.

Shop around for a welder, some can do mig and tig, others tig and arc (stick) and some do tig arc and plasma cutting ;) Comes in real handy, tig is good for fine work but its nice to have a mig welder to do real work aswell, similarly a plasma cutter for cutting

Also invest in an auto darkening welding helmet, pretty much gives you an extra hand to work with

AdamVR4
07-27-2012, 07:01 PM
What's an example of a decent one?

Miller and Lincoln have been the top dogs for a while now, I think.

My Dad's gotten a lot of use out of his miller syncrowave, but all said and done it cost a little over $2k several years ago.

Like I said though, it might be worth investigating the china TIG I posted earlier. If I recall, you can get them for way less than the advertised price... "just make an offer"



Also invest in an auto darkening welding helmet, pretty much gives you an extra hand to work with

+1!

Intropy
07-27-2012, 07:44 PM
Cool, all good tips, thanks guys.

RealMcCoy
07-27-2012, 11:58 PM
Get a brand name welder... Used on craigslist is always an option. I practically stole my syncrowave 180 that way. There's no way I could afford a machine like that new...

The best learning resource available on the web: WeldingWeb™ - Welding forum for pros and enthusiasts - Powered by vBulletin (http://weldingweb.com) (I suggest lurking, getting to know the players, and learning what you can with searches. When/if you do post, I suggest humility in the presence of masters... Some of those guys are amazing craftsmen, and more than willing to share what they know, but just as quick to rip an idiot to e-shreds...)

This site is one of the best on the web for instuctional videos: Welding Tips and Tricks - TIG, MIG, Stick and a pantload of other info (http://www.weldingtipsandtricks.com/index.html)

J. Fast
07-28-2012, 02:06 AM
IMO a Miller 211 and a spool gun is quite adequate for what you're looking to do J. For a hobby welder that's all you will ever truly need for steel or aluminum. You can generate the same quality welds as a TIG with a quality MIG by working slow and implementing good technique. Tig is cool and all but only if you're going to move into exotic metals, want to ooh and ahh, and can justify 4 grand on getting setup with a quality welder like a synchrowave. Add a tank, rods, gas, gloves, shields, a good hood, additional cutting and fab tools and you're off into the 5 thou range.

Only way to learn is to buy a setup, some metal, plug it in, clamp the ground and drop the hood. A really interesting analagy a great welder told me once. "Bead moves like water and cooks like bacon".

TurboSinceBirth
07-28-2012, 02:23 AM
I like my Miller Dynasty 200 welder for portability and ease of use although I'm hoping to get some more practice time in once I finish some projects so I can do my own FMIC fabbing plus maybe some exhaust work. If you don't mind the bulk a Miller Synchrowave 180 would be a good unit.