PDA

View Full Version : sequential ignition



Tigchamp
07-22-2012, 05:19 PM
Just an update about my AEM 8 Channel CDI & AEM short Coil On Plugs.
As I have the 8 channel CDI, I decided to go with Sequential ignition instead of wasted spark. I had a problem with the brand new AEM EMS 2, pin 91 which is the dedicated pin for number four coil was not working, instead of going through the hastle of sending the EMS off to the US, I got a local ECU repairer to fix it and now everything is working OK.
The main reason that I went with sequential ignition is that it enabled me to lose the PTU as well as the coil packs tidying up the engine.
Below are a couple of pics showing the setup, the blue wires going to the COP's are just covers, there are just two thin wires going to the COP's.
The CDI is under the stainless cover on the left of the engine bay, this is because one of the vents in my PRM hood is above it and the rain was soaking the unit.

http://i817.photobucket.com/albums/zz93/Tigchamp/006.jpg

http://i817.photobucket.com/albums/zz93/Tigchamp/007.jpg

http://i817.photobucket.com/albums/zz93/Tigchamp/005.jpg

Rebel
07-22-2012, 06:06 PM
How's the twin fire working for you? Mine would work fine until the engine got warm. Then it would misfire like crazy and make the car fall on it's face. I suspect it might be my ptu so I swapped another one in. Next step is removing the ptu altogether, but I like having the bypass plug option.

Tigchamp
07-22-2012, 06:21 PM
How's the twin fire working for you? Mine would work fine until the engine got warm. Then it would misfire like crazy and make the car fall on it's face. I suspect it might be my ptu so I swapped another one in. Next step is removing the ptu altogether, but I like having the bypass plug option.

To be fair I dont know yet as the car has not been on the road yet, although I hope to get it maped in the next two weeks and then we will see.
If you have a 8 chanel cdi I used the wiring on page nine which enabled me to remove the PTU.
Jeff

J. Fast
07-22-2012, 06:27 PM
Your build turned out so great! Congrats on everything. Go enjoy it! BTW, the COP upgrade is awesome. What was the dwell and charge difference between the OEM vs the COP?

Tigchamp
08-16-2012, 01:52 PM
Just a quick update, car is now on the road, CDI & COP'S are working fine at all temp's.
I dont beleive in running in engines so just putting a few hard miles on it to loosen it up before taking it in to be mapped.
I dont think I have to worry too much about knock as the TD05 20G's are only boosting to 12psi at the moment and there are big black clouds of excess fuel followed by 6ft flames coming out of the exhaust (running a bit rich lol)
Jeff

Intropy
08-16-2012, 04:43 PM
Love it. Can't wait till you turn it up.

SpikeyGG
05-14-2014, 06:32 PM
Just an update about my AEM 8 Channel CDI & AEM short Coil On Plugs.
As I have the 8 channel CDI, I decided to go with Sequential ignition instead of wasted spark. I had a problem with the brand new AEM EMS 2, pin 91 which is the dedicated pin for number four coil was not working, instead of going through the hastle of sending the EMS off to the US, I got a local ECU repairer to fix it and now everything is working OK.
The main reason that I went with sequential ignition is that it enabled me to lose the PTU as well as the coil packs tidying up the engine.
Below are a couple of pics showing the setup, the blue wires going to the COP's are just covers, there are just two thin wires going to the COP's.
The CDI is under the stainless cover on the left of the engine bay, this is because one of the vents in my PRM hood is above it and the rain was soaking the unit.

I know this is an old post but I'm very interested in doing the same thing on my set up to take advantage of the knock-per-cylinder detection/control of the AEM EMS series 2. I don't suppose you could share your setup details, like part numbers for coils, part numbers for coil drivers, specifics on dwell settings, etc.? Your engine bay looks very clean.

Thanks,
-Greg

Tigchamp
05-17-2014, 06:44 AM
I know this is an old post but I'm very interested in doing the same thing on my set up to take advantage of the knock-per-cylinder detection/control of the AEM EMS series 2. I don't suppose you could share your setup details, like part numbers for coils, part numbers for coil drivers, specifics on dwell settings, etc.? Your engine bay looks very clean.

Thanks,
-Greg

Sure Greg,
The coils I used are AEM 30-2850. If you are going AEM you can only use the 8 channel CDI as there are not enough coil outputs on the 4 channel one.
I used the instructions for wiring the coils to CDI on page 9 of the AEM 8 Channel CDI manual.
When you go into the coil setup in the AEM EMS 2, the crank settings are there for the other three coils you just need to check the box.
Jeff.

http://i817.photobucket.com/albums/zz93/Tigchamp/CoilonPlugs006.jpg

Tigchamp
05-17-2014, 07:48 AM
The coil drivers on the AEM EMS 2 are as follows.

Coil 1 - pin 10

Coil 2 - pin 23

Coil 3 - pin 11

Coil 4 - pin 91

Coil 5 - pin 82

Coil 6 - pin 85

You will note that although my AEM EMS 2 was brand new in the box, pin 91 was faulty and did not work so I had to get it repaired.

You will find more info in this thread, http://www.3sgto.org/3000gt-stealth-gto-related-topics/6355-total-jdm-gto-tt-rebuild.html

Jeff

SpikeyGG
05-17-2014, 11:03 AM
Jeff, thanks for the response! You only mentioned turning on coils #4-#6 but did you also disable #1B, #2B and #3B?

My current setup looks like this:
6766

It looks like I need to turn off the 'B' coils and turn on 4, 5, and 6 but also copy the "Coil Phasing" values from the 'B' coils to their respective new coils.

Also, did you need to change any of the advanced pickup options like "Spark Teeth"? I've been reading on these options and the base map I started with seems to already be configured to sequential ignition even though my ignition is the stock wasted spark setup. The following screen shot shows what I'm talking about. Wheel Teeth is set to 6 and so is Spark Teeth.

6767

I'll have to check my pin 91/coil#4 to see if it's busted too. :(

Thanks again. I'm getting excited about running sequential ignition!
-Greg

Tigchamp
05-17-2014, 01:16 PM
Jeff, thanks for the response! You only mentioned turning on coils #4-#6 but did you also disable #1B, #2B and #3B?

My current setup looks like this:
6766

It looks like I need to turn off the 'B' coils and turn on 4, 5, and 6 but also copy the "Coil Phasing" values from the 'B' coils to their respective new coils.

Also, did you need to change any of the advanced pickup options like "Spark Teeth"? I've been reading on these options and the base map I started with seems to already be configured to sequential ignition even though my ignition is the stock wasted spark setup. The following screen shot shows what I'm talking about. Wheel Teeth is set to 6 and so is Spark Teeth.

6767

I'll have to check my pin 91/coil#4 to see if it's busted too. :(

Thanks again. I'm getting excited about running sequential ignition!
-Greg

Yes Greg you are right, You need to turn off the "B" coils and use their values for 4,5 & 6. As far as anything else that you have mentioned I never changed Them.

Jeff.

SpikeyGG
08-10-2014, 10:08 PM
Tigchamp, if you're still around: I think the dash gets it's tach signal from the PTU. When you removed the PTU, did you just hook the "tach" output of the AEM CDI unit to the signal running to the dash? Or maybe your tach is broken?

Tigchamp
08-12-2014, 09:48 AM
Tigchamp, if you're still around: I think the dash gets it's tach signal from the PTU. When you removed the PTU, did you just hook the "tach" output of the AEM CDI unit to the signal running to the dash? Or maybe your tach is broken?

You are correct Spikey, although I also remove the plug that goes to the PTU I suspect that the feed is more than just one wire.

mjannusch
08-12-2014, 08:48 PM
Tach feed to the dash is just one wire at the PTU. The white one, if I remember right. I hooked my MSD DIS4+ tach output straight to that wire and it worked fine.

You can also run these types of coils just fine with a 4-channel CDI box in wasted-spark configuration and it works great.

Tigchamp
08-13-2014, 06:23 PM
It may be a dip switch on the 8 channel that I have to set as it is most definitely not working in sequential ignition. I have connected the tach feed via the white wire.

Tigchamp
08-13-2014, 06:25 PM
The AEM EMS2 knows what revs the engine is doing so perhaps there is a way of running the tach direct from the EMS.

SpikeyGG
08-17-2014, 01:33 AM
Tigchamp, would you do me a HUGE favor? I'm really curious what the primary resistance is on those 30-2850 AEM pencil coils; I don't suppose you'd measure it for me? :)

Thanks for all the help so far.