PDA

View Full Version : cel 41, no RH O2(front?) only in some cases.



Alan92RTTT
06-13-2012, 10:17 PM
In the morning heading to work the car runs fine.
When I stop for pop the rest of the trip in is fine.
In the evening on the way home its fine.
After the drive home if it sites about 30 minutes its starts throwing a CEL.

Pocketlogger says its a code 41 injector circuit.
When this is happening I'm not getting a cycle on the RH (front) O2
If I disable the injectors one by one Disabling #3 has no effect.


Suggestions?

Emilie@GZP
06-13-2012, 10:34 PM
Most likely your ecu.

Alan92RTTT
06-13-2012, 10:48 PM
Any other suggestions.

I'll pull it after work tomorrow and see what I see.

RealMcCoy
06-14-2012, 12:31 AM
I agree an injector driver in the ECU is very likely, the second most common possibility would be the #3 injector. That is really easy to check since the ECU is seeing a circuit problem. Just get it warm where it's having the issue, and put an ohmmeter across the injector. It will most likely have very high resistance if it is the cause of the problem. Since #3 is the center front injector, access is really easy, so that's probably the first thing I'd eliminate before pulling the ECU...

Alan92RTTT
06-14-2012, 12:39 AM
What is considered "high"

Please explain "put an ohmmeter across the injector." in word someone that clueless about electrical would understand.

RealMcCoy
06-14-2012, 12:47 AM
When you unplug the injector, there are two terminals in the connector. You are measuring the internal resistance of the coil in the injector. You would hook each lead of your ohmmeter to a terminal and take a reading. TT injectors are around 2.5(ish) ohms... To set a code, I would expect it to be several times that.

Alan92RTTT
06-14-2012, 01:04 AM
Just to make 100% sure.

Get error code.
Shut off car
pull #3 injector clip
check resistance on injector


No change in value for 450cc injectors?

RealMcCoy
06-14-2012, 01:14 AM
Just to make 100% sure.

Get error code.
Shut off car
pull #3 injector clip
check resistance on injector


No change in value for 450cc injectors?

Correct... And yes, the DSM 450's have the same specs.

Alan92RTTT
06-14-2012, 09:16 PM
I just tested the injectors and I did not get the result I expected.

I do not think I had the meter set right and its an old one that was my Dads. I know it was on Ohms I know that symbol.

Open it showed 10.000 with the 1 blinking.

Imo this says the injector is messed up. I left everything disconnected and I will go out later and check again and again in the AM.

On the injector closest to the trans(for comparison) I got 33(33 what I have no clue)
ON #3 it did not change from the open state.

RealMcCoy
06-14-2012, 09:53 PM
If the injector is going full open that would be an issue... 33 Ohms is also too high, you may have more than one with a problem.

Connect the leads of the meter together and make sure it goes to zero, then try the third injector in that bank to see if it shows a normal reading.

Amphiron
06-14-2012, 10:00 PM
Maybe I will bring my DMM up there this weekend and help you out. Saturday morning?

Alan92RTTT
06-14-2012, 10:42 PM
I'm thinking the scale is off. 33 is probably really 3.3

Touching the probes to each other nets a 0.0xxx numbers. If I use the clip I get a similar low number.

Saturday would be too late. If I can't sort this and have it stable tomorrow night early sat at the latest. its not going and the SL will.

Amphiron
06-14-2012, 10:49 PM
I said saturday morning, I can leave as early as 6 am. If I can get ahold of Larry I may be able to bring a 450CC injector.

Alan92RTTT
06-14-2012, 10:55 PM
Whats a DMM?

B-Man
06-14-2012, 11:08 PM
Alan, have you tried just swapping injectors and see if the code follows the injector or stays with the circuit?

Alan92RTTT
06-14-2012, 11:22 PM
NO, I have not tried swapping them

Alan92RTTT
06-14-2012, 11:38 PM
Checked again. #3 is giving the same numbers as the other injector now. CEL gone car runs smooth.


I'm calling it as the injector. Anyone got a blue 450cc injector and can get it to be my sat morning?

Hans@GZP
06-15-2012, 12:28 AM
I have some but shipping may be expensive.

Alan92RTTT
06-15-2012, 12:30 AM
overnight with sat am delivery yea that would be a bit much.

Hopefully someone local has one.

Amphiron
06-15-2012, 07:08 PM
Larry has a 550cc. I can try the the Junkyard tomorrow but you should try DSM graveyard, they will pull it for you, i'm sure they have one.

Alan92RTTT
06-15-2012, 07:42 PM
The problem is that they are in Grand Rapids. I don't want to be that far from home if their is an issue.

Looks like I'll be rocking the SL at the NG. :(

RealMcCoy
06-15-2012, 07:52 PM
Might give some of these guys a try... Maybe one of them is close and has what you need: detroit metro auto parts - all classifieds "DSM" - craigslist (http://detroit.craigslist.org/search/pta?query=DSM&srchType=A&minAsk=&maxAsk=)

Amphiron
06-15-2012, 08:19 PM
We should have called Autozone etc yesterday and got you one. I don't think anyone around here would have one in stock, you would have to do a 24 hour order.

Amphiron
06-15-2012, 08:22 PM
I can have one for you tomorrow. They will call it in and have it at 830 in the morning, it's going to be $199.00 however, for one injector. I will run it up for you, just pay me when I get there.
http://www.oreillyauto.com/site/c/search/Fuel+Injector/02521/C0024.oap?model=Talon&vi=1103094&year=1992&make=Eagle

Alan92RTTT
06-15-2012, 08:28 PM
I've got one one order from the local oreillys as a fall back

Amphiron
06-15-2012, 08:48 PM
okay i just told them to order it anyways let me know

sublime_whatigo
06-15-2012, 09:24 PM
The problem is that they are in Grand Rapids. I don't want to be that far from home if their is an issue.

Looks like I'll be rocking the SL at the NG. :(

Any way I can help Alan? Depending when you could be coming through Im sure I could help out so you don't have any issues.

Edit, I think I misunderstood the situation, either way off still stands if you need help with DSM graveyard. I know the owner and I'm nearby.

Alan92RTTT
06-15-2012, 10:06 PM
Thanks Matt, Its something I want taken care of before I leave this side of the state. Worst case I'll pick up the new one tomorrow. I made a few posts on xceed maybe that will shake something loose.

B-Man
06-15-2012, 10:49 PM
If DSM Graveyard has one and that's your only option, I SHOULD be able to bring it to you Monday....

Alan92RTTT
06-16-2012, 12:32 AM
I'll be in Indy monday that's a bit too late.

Alan92RTTT
06-25-2012, 10:16 AM
For anyone that cares it was definitely the injector. After installing a new on Saturday morning I have not had a repeat of the issue.

Toni
06-25-2012, 10:30 AM
I was wondering about that when when the ng started, then saw you going sideways at the cross and figured that you got it taken care of lol

Alan92RTTT
06-25-2012, 01:52 PM
I think sideways was the best way to take that corner :D