View Full Version : greasing transmission output shaft
i3igpete
05-17-2012, 12:43 PM
I could've sworn I read somewhere that some people don't recommend greasing the transmission output shafts and tcase input spools. This is hogwash.
http://tools.ticona.com/tools/documents/literature/B.1.1%20Spur%20gears%20with%20gearwheels-10.pdf
go to page 10, figure 11. Greasing gears reduces tooth wear due to oxidation (and then grinding off the oxidation) by 50% or more.
RealMcCoy
05-17-2012, 12:53 PM
I've never heard that one myself... I've seen plenty of discussion on what might be the best lube to use, but never heard anyone say don't lube it.
The one thing I'd add is to thoroughly clean and wire brush all rust from the shaft and sleeve prior to greasing it up. Iron oxide is incredibly abrasive, you don't want to create grinding compound with your grease...
i3igpete
05-17-2012, 01:03 PM
Yeah I don't remember where exactly I've heard it, but I know i've seen examples where people have pulled the t-case and the spool is repus rusty.
Chris@Rvengeperformance
05-17-2012, 01:32 PM
I've tried marine grease and it doesn't last. Last time I used antiseize based on some feedback from some pretty smart members, we'll see if that lasts.
Primus101
05-17-2012, 02:47 PM
The pressure on the spline faces actually promotes corrosion, it's termed 'fretting' Fretting and Its Insidious Effects, by EPI Inc. (http://www.epi-eng.com/mechanical_engineering_basics/fretting_corrosion.htm)
I have had good results with silicone brake grease, so no frettin' about my shaft:biggrin:
mcshooter
05-17-2012, 03:00 PM
i once put to much grease on and when putting the transfer case on it caused the cap in the transfer case to push off and allowed the transfer case oil to come out .. so grease it just dont overdo it
BigTyla
05-17-2012, 03:47 PM
This thread is just in time as I am going to be putting my transfer case back on soon. I assume the basic multi-purpose grease will do? I'm going to take a wire cup brush to the output shaft to clean the rust off before I reinstall.
AdamVR4
05-17-2012, 03:56 PM
I've always used silicone brake/all purpose grease too, and generally QUITE liberally, but mcshooter's post is pretty interesting. It takes a fair amount of pressure to press that freeze plug in/out. I'm shocked it didn't just blow the grease out.
i3igpete
05-17-2012, 04:07 PM
I agree, I would think it would take a lot of pressure to blow out a freeze plug.
Thanks for the fretting article, I couldn't remember the proper term.
RealMcCoy
05-17-2012, 04:33 PM
This thread is just in time as I am going to be putting my transfer case back on soon. I assume the basic multi-purpose grease will do? I'm going to take a wire cup brush to the output shaft to clean the rust off before I reinstall.
You also want to pay particular attention to the T/case sleeve... That powdered rust(iron oxide) from the fretting will hang out in there and cause you problems even if you grease it up. A small acid brush (looks like a stainless steel toothbrush) works great for cleaning them out.
A pertinent snip from the above link:
. In addition, the small fragments of metal which are broken off oxidize, forming oxide particles which, for most engineering metals, are harder than the mated parts. These particles become trapped between the mating surfaces and cause abrasive damage and scoring.
You let that stuff float around in your grease, and you've just created lapping compound....
Hmm I have always liberally coated with grease but I don't think I do a good enough job cleaning. I will have to give it a good cleansing next time I have it out. Thanks for the info!
AdamVR4
05-18-2012, 11:06 AM
You also want to pay particular attention to the T/case sleeve... That powdered rust(iron oxide) from the fretting will hang out in there and cause you problems even if you grease it up. A small acid brush (looks like a stainless steel toothbrush) works great for cleaning them out.
A pertinent snip from the above link:
You let that stuff float around in your grease, and you've just created lapping compound....
Makes a lot of sense.
Just to clarify, when you say "acid brush" you're simply referring to the style of brush, right? Not actually using acid on a brush? :p
Drweldin
05-18-2012, 11:23 AM
I've always used anti-seize with good results. This coupled with cleaning everytime should be PM every 15K if you're anal...maybe 30K if you're not, IMHO.
J. Fast
05-18-2012, 12:11 PM
Why anyone would say leave it dry is beyond me. One of the divisions of my employer deals soley with all sorts of structural metal on metal moving part and defect situations. Why you put grease there is pretty simple, it prevents galvanic coupling and asperities from forming. The type of grease utilized is important because it's creates a boundary layer film that seeks out the electrical fields in the micropores of the metal. It balances the electrical exchange which in-turn keeps the metal strong and prevents corrosion... aka fretting and rust.
For some strange reason I'm just envisioning this redneck guy sticking his finger in his mouth and greasing the input shaft with some spit when doing a clutch job. Kinda makin me chukkle.
Good point on recognzing the creation of valve lapping compound RealMcCoy.
cjbyron
05-18-2012, 12:54 PM
I've always preferred the Marine AntiSeize as that holds very well and designed for wet environments. It holds on much better than other AS. The kind with zinc has good properties for this type of application also.
Over the last year or so I've tried Loctite ViperLube for shafts which is a synthetic grease made for extreme conditions. So far it has done a good job and shafts remain rust free and still coated after long time. Good stuff.
Chris@Rvengeperformance
05-18-2012, 03:20 PM
it really is a bit of a disappointing design if you ask me. They could have done better.
RealMcCoy
05-18-2012, 06:48 PM
Makes a lot of sense.
Just to clarify, when you say "acid brush" you're simply referring to the style of brush, right? Not actually using acid on a brush? :p
Correct...
TurboSinceBirth
05-18-2012, 11:01 PM
I used synthetic grease before but anti-seize works much better.
i3igpete
05-31-2012, 04:06 PM
damn, i just used standard lucas axle grease this last time, maybe i'll try antiseize or a fancier brand nex ttime.
edit: found one of the older threads:
http://i6.photobucket.com/albums/y214/MADMarc/IMAG0122.jpghttp://i6.photobucket.com/albums/y214/MADMarc/IMAG0127.jpg
the splines are supposed to be dry. No fluid runs in there, the red is just rusty metal shavings from the shaft wearing out. It is a fairly common problem with OEM, and OEM replacement shafts. The way the car is driven has a lot to do with it to.
http://i.imgur.com/RZyQN.jpg
I've always preferred the Marine AntiSeize as that holds very well and designed for wet environments. It holds on much better than other AS. The kind with zinc has good properties for this type of application also.
Over the last year or so I've tried Loctite ViperLube for shafts which is a synthetic grease made for extreme conditions. So far it has done a good job and shafts remain rust free and still coated after long time. Good stuff.
Do any local stores carry the viperlube?
cjbyron
05-31-2012, 05:53 PM
Do any local stores carry the viperlube?
Depends on what's local I spoze. Grainger Supply stores carries it. But also easy to order online from places like drillspot.com or bettymills.com and the like. BettyMills probably has the most inventory, good prices, and ships fast.
ahh ok, I just didn't recall ever seeing in autozone,advanced, or napa. I do have grainger here so I'll check em out. Thanks.
Anyone have any more results/findings/updates? I am putting in a new 300m shaft and I'm sure that complicates things.
Chris@Rvengeperformance
04-04-2013, 02:52 PM
The spool was replaced when my billet t-case was made, but I am running a couple year old 300m shaft.
I used anti-size last time and when I had the t-case off it still looked like new. It had been about a year on there. It was still wet.
KeithMac
04-04-2013, 02:59 PM
I use coppa-slip anti sieze, said that a while back on 3si and got shot down in flames..
The spool was replaced when my billet t-case was made, but I am running a couple year old 300m shaft.
I used anti-size last time and when I had the t-case off it still looked like new. It had been about a year on there. It was still wet.
Do you recall what brand?
Chris@Rvengeperformance
04-04-2013, 03:11 PM
the silver permatex
Chris@Rvengeperformance
04-04-2013, 03:13 PM
I think it was this guy:
http://ecx.images-amazon.com/images/I/41JmRmAzSpL.jpg
same tub I've been using on stuff for about 6 years, almost out finally!
LOL I was glad you said that one because I have the same 5-6 year old tub.
R/T93
04-04-2013, 06:51 PM
Mine still looks 100% brand new and I believe it Is the original 98. It had a light rust coat over it, wire brushed and used the silver Napa stuff during re-assy.
From the phone.
Ninja Performance
04-04-2013, 08:29 PM
I have always coated them with grease in mine and customer cars and trans/tc rebuilds. Just finished a customer trans and TC rebuild and did just that.
-Chris
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.