PDA

View Full Version : Save some money, adjustable control arms now bundled with springs and coilovers!



Maximal
04-23-2012, 01:36 PM
Suspension - Maximal Performance (http://www.maximalperformance.com/store/suspension/cat_3.html)

Check them out. Discounted the control arms when you guys bundle them with a lowering spring or coilover setup. For example, you're saving $30 when you order them with the Megan coilovers.

Any questions...let me know.

Maximal
05-01-2012, 04:33 PM
Bump!

Maximal
06-13-2012, 10:49 AM
Another bump!

Maximal
08-10-2012, 03:55 PM
Still have this offer going...

Roybatty
09-04-2012, 03:59 PM
Free bump! Any sales coming up for just the awd rear adjustable control arms

Maximal
09-04-2012, 05:29 PM
Probably not, with a recent price increase on parts there isn't much room to discount the arms much. :(

Roybatty
09-07-2012, 04:29 PM
I am ordering it anyway...evidently the toe or camber can't be adjusted enough to get it to factory spec anymore.

Hey, wanted to mention site is working without a hitch. Had trouble trying to "print receipt" but not a big deal at all really, just fyi.

niterydr
09-11-2012, 12:13 PM
Has anyone compared the Megans to the Tein offerings?
Spring rates?

Roybatty
09-21-2012, 01:56 PM
Is this the correct diagram for the awd adjustable rear control arm? Any other installation instructions/pitfalls to be aware of? lmk, thanks
http://i986.photobucket.com/albums/ae349/Stealth2turbo/Stealth/UpperandLowerCAs_zps7d52be88.jpg

Maximal
09-21-2012, 05:13 PM
Yep, just remove the stock one and install the new one. You want to make the aftermarket one about the same size as the stock one to start out and adjust from there (preferably have an alignment shop do it).

Roybatty
09-24-2012, 12:27 PM
What do people use to remove the old control arm? I am assuming no one buys the special tool. I plan to try a regular pry bar/pneumatic chisel/pb blaster.

familyMAN
09-24-2012, 12:37 PM
Cheap harbor freight separator and BFH worked like a charm.

Maximal
09-24-2012, 12:57 PM
What do people use to remove the old control arm? I am assuming no one buys the special tool. I plan to try a regular pry bar/pneumatic chisel/pb blaster.

A big hammer works well for the tie rod ends. For the other end I usually cut them off. They rust in the bushings and there's really no way to get them out. You can get a sawzall in between the bushings and the bracket. Hack off each side and it'll fall right out.

dbest671
09-24-2012, 01:04 PM
Stupid question is probably stupid... do the heim joins need dust covers/boots? If so, can you put them on if I buy them :suspect:.

Maximal
09-24-2012, 01:08 PM
Stupid question is probably stupid... do the heim joins need dust covers/boots? If so, can you put them on if I buy them :suspect:.

I don't offer them but you can get them pretty cheap on ebay (I think that's where most get them). They really just slide on but I guess if you want me to buy some and slip them on I can. :p

If you're worried about durability I'd go with the teflon option I offer. With that, as long as you're not driving in lots of snow/salt you shouldn't have issues without covers.

Roybatty
10-12-2012, 05:53 PM
http://www.3sgto.org/f17/dust-boots-3sx-adjustable-control-arms-7566.html

http://www.ebay.com/itm/Seals-it-RERS3-Single-Rod-End-Boot-Heim-joint-Spherical-Metric-Male-Female-/320765853560

Was in process of getting these and figure it may do some good for people looking at this thread.

Maximal
11-07-2012, 03:55 PM
Bumping this!