View Full Version : Drivetrain Bad Thump in Drivetrain "Not The Driveshaft"
DrGonzo
04-12-2012, 02:43 PM
For the longest time now I have had a really bad thump in the drivetrain that usually occurs when I'm in a gear and give it gas. The issue is too much slack in the drivetrain and when I give it gas it will thump bad until the slack is taken up.
I initially though it was the driveshaft for two reasons, Every thread about drivetrain thump gets directed to Bad Carrier bearings and I had a lot of slack in my driveshaft.
I swapped out the driveshaft with another and still the same issue, I swapped out the read diff and still the SAME ISSUE!!!!
So I checked the Driveshaft again and even the used replacement had a lot of up/down - side/side play. Well I was not going to drop almost $200.00 on new carrier bearings as I was still not convinced it was the carrier bearings caused the thumping. So I took my spare driveshaft and willed in the carrier bearing doughnut with polyurethane. Let it setup for about a week and re-installed it. There is ZERO play in the driveshaft now but I can twist it almost two inches either direct.
Why is there so much slack in the driveshaft? This slack is what is giving me the damn thumping and I don't know how to alleviate it. Any Ideas??
futurevr4man
04-12-2012, 04:01 PM
Check your motor mounts
DrGonzo
04-12-2012, 04:18 PM
Check your motor mounts
There Solids......
Chris GTO TT
04-12-2012, 05:16 PM
Output shaft stripped
DrGonzo
04-12-2012, 05:58 PM
Here's pics of the output shaft I took in Nov 2011. Car had pretty much been sitting since then as I didn't drive it much in the winter.
http://3s.gonzoinc.com/albums/userpics/10002/DSCF1382.jpg
http://3s.gonzoinc.com/albums/userpics/10002/DSCF1383.jpg
http://3s.gonzoinc.com/albums/userpics/10002/DSCF1384.jpg
DocWalt
04-12-2012, 09:55 PM
T-case slop or tranny internals then.
Nihil
04-14-2012, 03:24 AM
You try adjusting rear diff backlash? That's on my to do list...there's an informative thread on the other site...
DrGonzo
04-14-2012, 08:19 AM
You try adjusting rear diff backlash? That's on my to do list...there's an informative thread on the other site...
Got the URL for that thread? All the ones I have read don't have any decent details on it. Manual is pretty shady about the procedure also.
Nihil
04-14-2012, 11:49 AM
I hate linkin to the other site ha but yeahhhh....here ya gooooo Adjusted Rear Diff Backlash, some hints - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f35/adjusted-rear-diff-backlash-some-hints-182268/)
Jimvr4
04-14-2012, 03:17 PM
It's pretty easy to measure the backlash and see if you have a problem. I had a leak at the pinion seal and ended up measuring BL just to make sure everything was OK. I just needed a new seal as the old one was worn out.
DrGonzo
04-15-2012, 01:26 AM
Yeah I need to pick up a dial gauge and check it out. I pulled up a youtube video to better help explain it as I couldn't follow his write-up on the other site and the manual made no sense either. After seeing the video it is all clear now. The original dif I replaced thinking it would fix the thump is still in my shed. So I'm going to check it first since it's already out and easier to work with. Once I get it into spec I'll just swap out the dif's.
Jimvr4
04-15-2012, 04:13 AM
Link to youtube video?
DrGonzo
04-15-2012, 10:29 AM
It's and old video and they are adjusting a Ford 9" but the concept is the same:
http://www.youtube.com/watch?v=bSCUck4M6W4
Streamln1
04-23-2012, 03:30 AM
Could be a worn CV joint, best way to tell is to get the car up in the air and start moving stuff around, use something to hold the driveshaft from spinning and then try turning the wheels one by one and you can find where the slop is coming from.
DrGonzo
07-09-2012, 10:33 AM
So I finally got around to checking the backlash on the dif and it was perfect at .004.
So I have eliminated everything in the back end now. It must be coming from the front drive train. Either the Transfer case, Trans or half shafts... Blah this problem is driving me nuts!!!
DocWalt
07-09-2012, 11:12 AM
I assume the diff carrier bushings are good. If they are, my original post still stands :)
DrGonzo
07-09-2012, 11:42 AM
Yeah all of the bushings are nice and stiff. Drive shaft carrier bearings were poly filled so they are also solid. I know it's not the output shaft as it was checked already. Going to start with the transfer case and work my way back through the front drive train.
Nihil
07-12-2012, 02:45 AM
Drive shaft carrier bearings were poly filled so they are also solid.
Just curious about this, did you do the old school window urethane fill, or actually "re-build" them so to speak and fill with poly?
Going to start with the transfer case and work my way back through the front drive train.
I'm hopefully gonna get to all of this drivetrain maintenance this summer, and I don't think there's any decent write-ups around with pics or vids n tips...any chance you'd do anything like this? Just figured I'd ask :)
DrGonzo
07-12-2012, 09:32 AM
I used a polyurethane sealant almost like the window urethane. I bought a couple different tubes and did some tests beads to figure out which would work better. I found a construction grade poly that was tough but still plyable. I don't remember the name though.
I'll see what I can do. I've not messed with the transfer case beyond resealing it so it will be a learning experience for me also. I will most likely be sending the trans off to get rebuilt as I don't have the tools here to do a proper rebuilt and honestly I really don't want to mess with rebuilding the trans.
green-lantern
07-12-2012, 01:58 PM
This could still be the driveshaft, just filling the mounts won't eliminate the problem, just the slap.
My issue was the clutch. The rivets got loose causing the slack.
Your output shaft and spool were good right? Have you jacked the front up and tried to move the wheel back and forth? You could try it with one wheel up at a time then both up at the same time.
Edit: Oh but BTW my drivetrain got a lot tighter after I got the aluminum driveshaft. So it did help take up some of the slack. Actually it feels real tight now.
That' what she said
DrGonzo
07-12-2012, 02:53 PM
Well there is no movement in the drive shaft at all not. I also just replaced all of the mount bushing with new OEM as the old ones were falling apart.
Output shaft was fine. I haven't checked the spool yet. It's on my list of things to check when I check out the transfer case. Still running a stock clutch
I have some play in the front wheels which I know is from the steering rack itself. Front Wheel bearings where replaced and half shafts are all good.
green-lantern
07-12-2012, 04:52 PM
Well I couldn't actually see any play in my shaft but the PST definitely made a big difference. It's a good upgrade if you got the cash anyway. I hope you can figure it out before BRG but if you don’t then take me for a ride and maybe I can give some ideas.
DrGonzo
07-12-2012, 05:37 PM
Yeah It won't be fixed before BRG. I've been dealing with it and the trans rattle far over a year now. I'll take ya for a ride and BRG so you can feel it.
green-lantern
07-12-2012, 06:12 PM
You know what cured my trans rattle? I bent the clip that holds the fork to the ball in so much it was very hard to get back on. I had to reach in behind the fork and hold the clip out to slip it on. Anyway that took care of it.
anyonebutme
07-12-2012, 08:37 PM
local car thumps under accel and in reverse, I think it's a broken front diff, will know shortly.
DrGonzo
07-12-2012, 09:19 PM
You know what cured my trans rattle? I bent the clip that holds the fork to the ball in so much it was very hard to get back on. I had to reach in behind the fork and hold the clip out to slip it on. Anyway that took care of it.
I put a stethoscope on the trans and the noise if from inside. the gear housing. I changed out the bearings thinking that was the issue and still rattling... you'll hear it next week.
dbest671
07-12-2012, 09:39 PM
How are the u-joints on the driveshaft itself? I believe lawdogg changed the u-joints on his. There are several threads on the issue on the other site.
DrGonzo
07-12-2012, 11:14 PM
U-joints are good. No binding and still smooth .
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.