PDA

View Full Version : Installed Stack Pro-Control Gauges



SilverJester
09-20-2010, 12:31 PM
I installed some new Stack Pro-Control Gauges (boost, water temp, and oil pressure) and thought I would share. These things are pretty cool, they don't require a control module like defi's. Each gauge can trigger 2 separate functions (e.g. the water temp can act as a 2 stage fan controller). Each gauge has 4 warning levels (2 low and 2 high), which will change color to any color you preset for level 1 warning and flash at you for level 2 warnings (hi and low colors can be different). In the pictures below the blue is what I choose for my low warning color and red for high (car was off so water temp was cold and I haven't hooked up the oil pressure sensor yet). It also has a peak recall that is remembered even after you turn the car off (as you can see my car is having some overheating issues :( )

pics:
http://farm5.static.flickr.com/4132/5008078559_3196e05855_b.jpg
http://farm5.static.flickr.com/4149/5008078951_9f5d65166a_b.jpg
http://farm5.static.flickr.com/4091/5008685900_35e6ac0b05_b.jpg


My one issue with them is that they are bright! In this shot you can see them next to my EL gauge cluster overlays (which used to match perfectly with my posports in white):

http://farm5.static.flickr.com/4144/5008686188_cd00b0233d_b.jpg

I'm not sure if they can be dimmed...the instruction are kinda unclear about the dimmable lighting mode. "Dimmable: In this mode, the white wire is used to set the intensity of the dial lighting from full brightness down to off." I'm not sure if that means they are dimmed or if it just turns off the lights.

P.S.
You can also choose the color of the gauges during normal operation (not in warning mode), I just like white. But you can choose from red, green, yellow, blue, purple, turquoise and white.

akotten
09-20-2010, 01:23 PM
Looks good! Where did you get your main gauge cluster overlays?

SilverJester
09-20-2010, 01:25 PM
On ebay: http://cgi.ebay.com/ebaymotors/91-99-Mitsubishi-3000GT-Indiglo-Gauges-Dials-Kit-180MPH-/270625404183?pt=Motors_Car_Truck_Parts_Accessories&fits=Make%3AMitsubishi|Model%3A3000GT|Submodel%3AV R-4&hash=item3f0287f517

akotten
09-20-2010, 01:52 PM
OK, thats what I thought. Are they only indigo or can you get them to display in pure white?

i3igpete
09-20-2010, 01:54 PM
i LOVE stack gauges :14:

Atrosity
09-20-2010, 01:56 PM
How accurate are these?

SilverJester
09-20-2010, 02:01 PM
Interesting to note that the oil pressure gauge uses an autometer sensor. The water temp was was right on with my data logger.

DocWalt
09-20-2010, 02:01 PM
STACK FTMFW. Did you find these in that other thread? lol, I thought I was the only one with a 3s that wanted these. How was the install, besides the unclear bits in the instructions?

And yes, They should be dimmable... I'm not sure how, but I know they have a dim function. Call up STACK and ask :p

SilverJester
09-20-2010, 02:05 PM
Yeah prob the same thread you saw them in :)

I emailed stack (tried calling and they didn't have tech support, just an automated message). I'll play around with the white wire that is suppose to dim and/or turn off the lights this weekend when I have some time.

Each gauge has a fair amount of wires in the "harness" 9-10 wires. But they don't come wrapped together. So I spent a good amount of time taping up wires together to form a neater harness. But aside from that, the install was easy.

DocWalt
09-20-2010, 02:13 PM
Ok, sweet. I'm wondering if there's supposed to be a resistance put on that wire, or fed the voltage from the dimmer rheostat... I wouldn't pump voltage into it until you know for sure, lol.

Sounds like a pretty easy install, thanks!

SilverJester
09-20-2010, 02:54 PM
The instructions say "+12v Dash Lighting" I'm thinking you maybe right and I'll tie it into the rehostat. But even still, hooking it up to another power source would either dim it to a preset dim (or fully off) or not dim it at all (since there would be no resistance on power). I'm not too worried about it, I'll play around with it later.

DocWalt
09-20-2010, 03:25 PM
Ah, ok, so it sounds like using the rhesostat will work. Sweet. I just wonder how dim they'll get compared to the EL. Looking nice :) :367023_u68:

SilverJester
09-23-2010, 10:16 PM
Alright so I'm not great at wiring, can someone help me with figuring out how to wire up the dimmer light? I did some testing and there is a white +12v wire that can be used to dim the lights on the gauges (if the correct mode is set on the gauge). In this mode the lights are proportional to the voltage on the white wire (no voltage no light). The stock gauges use a rheostat ground wire to dim them (I need a positive wire). Also with the headlights off (aka daytime), I'd like the lights to be on full power. Guessing I'll need a relay to trigger the white wire's power source between a normal "full power" wire and one controlled by the rheostat. Can anyone help me out here? Small words please lol, I'm terrible at wiring.

DrGonzo
09-23-2010, 10:41 PM
Dimmer is not going to be possible with the stock lighting! The stock dimmer rheostat controls dimming on the negative side not the positive side! I just installed Prosport gauges in my dash about a week ago and ran into the same issue. Looked over the stock wiring and found out that the rheostat dims on the negative side.....

There is nothing on the stock wiring that will let you dim using the stock dimer. You would have to build a new dimmer switch/rheostat to control the new gauges!

DocWalt
09-23-2010, 10:54 PM
SPDT Relay:
http://www.rowand.net/shop/tech/images/RelayWiringGuide.jpg

86 and 85 would be spliced into a 12V line that has power only when the headlights are on (No, I don't know what to use, maybe directly in the 12V feed to the headlights? If you do that, make damn sure the relay can handle the load) and 87a would be a 12V feed, 87 would be the after rheostat feed. 30 goes to the gauge.

edit: wait? The rheostat dims the negative side? That's... uh. well it makes sense, that's all I can say, lol

SilverJester
09-24-2010, 12:32 AM
Hmm, I'm going to have to do some digging. There's got to be a way to convert the resistance on the rheostat's negative output into a + signal.

DocWalt
09-24-2010, 01:23 AM
There is, but I'm on my phone now and can't find any easy way to explain it. If you don't find anything, I'll try to post something up tomorrow. :)

SilverJester
09-24-2010, 11:57 AM
Yeah that would be great thanks

DocWalt
09-25-2010, 12:14 AM
So, I had my dad who does this for a living look it over. Yep, since Mitsu did the gauge wiring backwards, this is going to be a real bitch, lol. He said he'll draw up a wiring diagram that will work.

edit: Obviously just adding your own rheostat will work as well, and will be infinitely less sucky in the long run.

SilverJester
09-25-2010, 02:28 AM
After thinking it over I am just going to install a potentiometer to dim the lights, and a relay so that the gauges are dimmed at night (using power from potentiometer) and during the day they are on full power. I realized I like to have all the other lights the rheostat controls fully lit, but the stack gauges are just way to bright at night to be fully lit, so a separate control just makes more sense. Thanks for the help though guys!

KeithMac
09-26-2010, 12:14 PM
Jump the connector on the rheostat to give full power to the stock lights and then wire the rheostat itself up to +12v to control the Stack`s?.

DocWalt
09-26-2010, 01:23 PM
Jump the connector on the rheostat to give full power to the stock lights and then wire the rheostat itself up to +12v to control the Stack`s?.

The stock gauges are wired "backwards" with the rheostat on the ground side. It works, but it's dumb.

KeithMac
09-27-2010, 12:33 PM
If you`re happy with the normal gauges on full brightness you can just unplug and jumper the connector, you then have the rheostat free to wire up as you wish to use with the Stack`s (convert it to +ve feed).

Chris@Rvengeperformance
09-27-2010, 03:23 PM
hmm I'd have to check exactly how I have my greddy gauges setup, but I'm using the stock rheostat just fine.

VR-4ever
09-30-2010, 02:33 AM
i LOVE stack gauges :14:

I second this fine gentleman's statement.

OBXBoost
09-30-2010, 09:13 AM
I second this fine gentleman's statement.

as if you know jack about stack.

:D