View Full Version : Brakes caliper mount hole on knuckle is stripped
i3igpete
03-05-2012, 10:41 AM
The threads on one bolt were screwed up but I didn't notice until recently. I replaced the bolt and retapped the hole on the steering knuckle. Turns out the threads were so bad that the hole is now completely flat on the inside for half it's depth.
I've tested the strength of the remaining threads by overtorquing past spec, but I still don't completely trust it once things start heating up. Should I helicoil it?
What is the next size up I should use to drill out and re-tap? I believe the stock bolt size is M12x1.25. I'm guessing I should just jump to M14x1.25.
According to this, I should predrill it with a 12.8mm bit first, right?
http://en.wikipedia.org/wiki/Drill_and_tap_size_chart
Chris@Rvengeperformance
03-05-2012, 11:09 AM
You can helicoil it or drill it and the caliper out to 1/2"
That's only half a mm bigger, but would probably be enough to make good threads.
DocWalt
03-05-2012, 11:43 AM
You can helicoil it or drill it and the caliper out to 1/2"
That's only half a mm bigger, but would probably be enough to make good threads.
Agreed. I wouldn't trust that kind of thread depth for something as important as brakes either.
green-lantern
03-05-2012, 11:48 AM
I'd replace the knuckle Pete.
i3igpete
03-05-2012, 12:55 PM
trying to avoid replacing the whole knuckle, since I think that might cause more problems than it's worth if I end up breaking bolts or finding something seized.
vroom4
03-05-2012, 01:02 PM
I would helicoil, but if you do go a size bigger dont do m14x1.25...that is a very weird size :lol: m14x1.5 i believe. Also you dont have to be dead on with the drill size. a little bit smaller hole is fine if it ends up being a drill bit that costs like 10$.
cjbyron
03-05-2012, 01:22 PM
If you can get the bolt up to torque spec then that's a good. For a little bit more reassurance you could use some loctite high temp product such as the #2630 which is made for holding 12-25mm fasteners and up to 650deg w/ break torque of 160ftlbs.
If you do tap new threads perhaps a 1/2" SAE would work okay since that is just slightly over 12mm. No need to stay metric on the fastener right? As for what size drill bit to use, it should be stamped right on the tap.
anyonebutme
03-05-2012, 11:31 PM
It wouldn't bother me, the caliper bolt is almost completely loaded in shear anyways.
RealMcCoy
03-06-2012, 12:19 AM
I don't understand the issue...? If it's a 12X1.25 bolt, put a 12X1.25 helicoil in it, and install a factory bolt... The helicoil tap will have the necessary drill size stamped on it.
12X1.25 helicoil kits aren't real common, I had to look pretty hard for mine, but with half the Getrags I work on having stripped trans mount holes, it was needed...
J. Fast
03-06-2012, 12:21 AM
Use a Time Sert re-thread kit Pete. They make in every SAE or Metric size. You can likely buy a whole kit for $50 on Ebay. The repairs are very strong, much better and stroger than heilicoil.
m14 time sert - Bing Images (http://www.bing.com/images/search?q=m14+time+sert&qpvt=m14+time+sert&FORM=IGRE#x0y123)
J. Fast
03-06-2012, 12:24 AM
I don't understand the issue...? If it's a 12X1.25 bolt, put a 12X1.25 helicoil in it, and install a factory bolt... The helicoil tap will have the necessary drill size stamped on it.
12X1.25 helicoil kits aren't real common, I had to look pretty hard for mine, but with half the Getrags I work on having stripped trans mount holes, it was needed...
You should use the Time Sert repair kit for that too. They make Copper, Aluminum, Steel, Cast, Galvanized... all different types of plugs for thread repairs so you don't get issues with dissimilar metals.
RealMcCoy
03-06-2012, 12:32 AM
I'm also a fan of Time-Sert... Particularly for reataching the cylinder heads to a Northstar :D
I'm still not understanding the need to go larger than the original bolt size..?
i3igpete
03-06-2012, 01:00 PM
going to the bigger bolt was because i don't really trust helicoil, so that is the next cheapest option besides replacing the hub entirely. Will helicoils work with thru-bolts like on the steering knuckle? I always see them with the tang on the end which I thought was only for blind holes.
I guess i'll go with a timesert since those are made for thru holes
cjbyron
03-06-2012, 01:07 PM
You just knock the tang off. Use a large punch. I think the package even has instructions for that.
i3igpete
03-06-2012, 01:08 PM
god damn this is getting pricey quickly
Amazon.com: TIME-SERT M12 X 1.25 Metric Thread Repair Kit 1212: Automotive (http://www.amazon.com/TIME-SERT-Metric-Thread-Repair-1212/dp/B001ZS2BJ4)
in retrospect maybe I should have just cranked down on the bad threads with the new bolt instead of trying to retap them.
RealMcCoy
03-06-2012, 01:21 PM
The tang on the end of a heli-coil breaks away... You're supposed to remove it even in a blind hole. I wouldn't have any problem at all with a heli-coil in that application. The only worry I have with time-sert is if the parent metal is too thin, and you end up taking too much away to install the insert. Otherwise I agree, they are a great option.
i3igpete
03-06-2012, 07:58 PM
orrr maybe i should just get a longer bolt and put a backing nut on the other side? (is the backside flat for this? I assume so)
this seems like the least fuckup-able option. :scratchchin:
Chris@Rvengeperformance
03-07-2012, 12:26 AM
orrr maybe i should just get a longer bolt and put a backing nut on the other side? (is the backside flat for this? I assume so)
this seems like the least fuckup-able option. :scratchchin:
I think it would hit the rotor
i3igpete
03-07-2012, 01:17 AM
damn it, forgot how close it was there (daveslow actually dug a hole into a rotor using an ace hardware bolt)
edit: son of a bitch don't tell me the OEM thread size is actually m12x1.5, because if so... :angry2:
apickle
03-07-2012, 06:33 PM
Time-sert or Helicoil have always performed the same for me, fwiw. If the area I'm retapping is already rather thin, I'll use a time-sert since it's a solid piece. Otherwise I have about 8-12 metric Helicoil kits stacked on a shelf for the most common metric sizes. For the caliper>knuckle, either should work.
anyonebutme
03-07-2012, 07:17 PM
Pete......put the sawzall down and slowly back away from the vehicle...... /policevoice
stealthee
03-07-2012, 08:52 PM
Either helicoil or replace the knuckle. Knuickle replacement isn't all that difficult.
And as far as heat is concerned, I've helicoiled spark plugs in a 3.1 GM before. Heat would be a lot greater there than on a steering knuckle and the thing held solid. The car ran great until the body started falling apart around it.
wraith
03-11-2012, 01:42 PM
wow, that sucks. my inner cheapskate would just use loctite and trust the remaining threads. The engineer in me would want to do it like oem and replace the knuckle from a partout and then do an r&r on the a arm and the BJ for the steering link.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.