View Full Version : Suspension AWD addco rear sway bar installation help needed
Rakuny
02-24-2012, 11:51 AM
I just finished my rear end and after struggling a lot with the endlinks finally was able to get the swaybar installed.. I got the subframe up and found that the axle nuts hit the swaybar on the drivers side. Anyone else have this problem? Suggestions?
Passenger side clears.. barely..
http://img853.imageshack.us/img853/113/1002928n.jpg (http://imageshack.us/photo/my-images/853/1002928n.jpg/)
Drivers side hits...
http://img403.imageshack.us/img403/3100/1002932d.jpg (http://imageshack.us/photo/my-images/403/1002932d.jpg/)
Any help will be greatly appreciated.
J. Fast
02-24-2012, 12:36 PM
O_o Can you take an expanded pic of the whole rear end and end links?
Rakuny
02-24-2012, 01:31 PM
I can later today.. I just got home.. I got stuck leaving where the car is at and got stuck when I got home.. the day after I finally get the part I was waiting for and have time off work we get a shit ton of very heavy sticky wet snow.. not my day lol
I will also say that by "struggled getting the endlinks connected", I mean I still can't believe it went together.. holy tight fight. I litterally had to use a pry bar on the sway bar against the subframe to get the rear sway bar bracket bolts in..
BTW, I tried to get more weights so I could add them up and have a total weight for the rear subframe and everything.. when I tried to weigh the differential I felt like I was going to break the scale and it error'd because the reading was too high for the scale.
Edit: the sway bar also hits the floor now that I've installed the subframe.
R/T93
02-24-2012, 02:36 PM
Some other guy had problems with it hitting the floor, 3sx said something along the lines of, "it worked on our test mule".
Saner or bust, IMO.
B-Man
02-24-2012, 02:54 PM
You could try bending it :dontknow:
Bummer though.
Rakuny
02-24-2012, 03:21 PM
thinking about throwing the stocker back on and eating the cost. The fitment on this thing is a joke. It shouldn't be a big accomplishment just getting the endlinks connected. As it happens I was super stoked to finally get it.. only took me 2 hours.. :(
Edit: just to clarify about the floor hitting issue.. I did NOT use the supplied shims under the sway bar brackets.
Vantage
02-24-2012, 04:08 PM
Hopefully Maximal can chime in and help you because he sells them, so I would think he would know..
B-Man
02-24-2012, 04:13 PM
If you run just the front swaybar, you might experience more understeer.
Rakuny
02-24-2012, 04:45 PM
Maximal can't get the AWD ones, he only sells them for FWD.
I am gonna try to move the mount forward on that side.. I didn't bother with it earlier because the bar is already hitting the floor and I don't think it will work.. I don't need much clearance though... I'm also gonna jack through the suspension motion to see if there are any other interference issues.
I ordered new brackets (I broke mine getting them off) and bushings for the stock bar just in case..
If you run just the front swaybar, you might experience more understeer.
I think otherwise, I'll shoot you a message later
Rakuny
02-24-2012, 08:41 PM
I was able to loosen the one bracket and pry it back and it cleared.. as soon as I jacked the suspension through it's travel it hit again.. it hits the worst in the middle of the travel. more pics of whole sub frame and sway bar hitting the floor.
http://img201.imageshack.us/img201/7186/1002934x.jpg (http://imageshack.us/photo/my-images/201/1002934x.jpg/)
http://img252.imageshack.us/img252/1087/1002935.jpg (http://imageshack.us/photo/my-images/252/1002935.jpg/)
http://img41.imageshack.us/img41/301/1002936vy.jpg (http://imageshack.us/photo/my-images/41/1002936vy.jpg/)
http://img803.imageshack.us/img803/9478/1002937.jpg (http://imageshack.us/photo/my-images/803/1002937.jpg/)
http://img513.imageshack.us/img513/3575/1002941ig.jpg (http://imageshack.us/photo/my-images/513/1002941ig.jpg/)
http://img403.imageshack.us/img403/3108/1002942t.jpg (http://imageshack.us/photo/my-images/403/1002942t.jpg/)
http://img688.imageshack.us/img688/1083/1002945m.jpg (http://imageshack.us/photo/my-images/688/1002945m.jpg/)
anyonebutme
02-24-2012, 09:13 PM
Looks to me the end links are too long and the bar isn't long enough. The hitting the floor I'd guess is from them trying to get as much clearance away from CFDS as possible instead of doing a compound bend operation. I haven't installed mine yet, but with all my other modifications I don't think I'm going to have these issues.
If I was you I'd BFH the floor and grind down the link a bit.
Rakuny
02-24-2012, 10:00 PM
Thanks, I'll give it a try tomorrow.. it's just weird to me that one side hits and the other does not.
anyonebutme
02-24-2012, 10:23 PM
Also, how tight did you tighten the end link bolts? Looks the the bushing isn't compressed any. Tightening them until the bushings have a slight bulge might give you some clearance as well.
terrets
02-25-2012, 01:58 AM
I think otherwise, I'll shoot you a message later
http://www.houseofthud.com/cartech/swaybars.htm
Good read I just learned this today haha.
Also, Id suggest running the car without swaybars and see how it reacts, then make your decision.. Least it seems like a good plan to me. Haha, its what Im going to do after the new suspension is in.
That angle just seems a little off to me, are you sure its not upside down? :p
Either way thats a bummer it doesnt fit. Im not sure Id trust it being that close to the axles even with grinding it down, because shits going to shift... Even if its the slightests, thats a little close for comfort for me at least..
you call that a snow blower? :)
J. Fast
02-25-2012, 07:38 PM
If I was you I'd BFH the floor...
^^This^^ Smash it!
...and grind down the link a bit
IDK, it looks like it's going to rub the subframe if he drops the link and doesn't raise the bar and bring it forward in the tunnel. That bar needs some kind of modified bracket and a sleeve support to push it forward in the tunnel.
B-Man
02-25-2012, 08:28 PM
Did you have a hard time getting the swaybar links on because it's pressing against the floor? Looks to me (kinda hard to tell by pics) that if you fix the pressing on the floor issue and had a hair shorter links, everything would clear.
anyonebutme
02-25-2012, 09:10 PM
OK, just went to the garage, threw the stock arms on the subframe, and bolted in the Addco sway bar. Few things I found:
1. extend your adjustable control arms so they are not bottomed out, just a few turns is enough. I don't know where these will end up after an alignment, but I can definitely see where this can limit my neg camber in the back.
2. adjust the lower arm camber to full positive (both bolts toward each other/center). After installing the links this car be adjusted back maybe.
3. bolt the bar to the subframe loosely, turn the endlinks a couple turns onto the lower control arm, Then insert the connecting bolt from the link to the bar, I had the entire bar bolted in 10 minutes once I sat there for a bit looking how everything went together. Cleared the axles...barely.
So far without the subframe being on the car I spotted a few issues. One being the links are a bit too long, the other is that the bar total width and arm length is wrong causing the links to be on the wrong side of the bar. This is the entire issue with this bar, 1" or less arm length (would affect the stiffness of the bar, I'll measure it and see exactly what this bar is to start) and a couple degrees change in the arm bend and this install would be cake.
To Jeremy: There's plenty of room for droop, I can attach the bar to the bottom of the lower arm if I wanted.
Pics will be had once I'm cleaned up. Without the subframe in the car it's a whole 'nother thing than trying to install it in the car, but so far I'm thinking it'll bolt in fine until I find another issue.
anyonebutme
02-25-2012, 09:47 PM
http://img.photobucket.com/albums/v55/PrestoTuna/2012-02-25192655.jpg
http://img.photobucket.com/albums/v55/PrestoTuna/2012-02-25192633.jpg
http://img.photobucket.com/albums/v55/PrestoTuna/2012-02-25192621.jpg
You see by the angle of the end link, that the bar is too short and at a funny angle:
http://img.photobucket.com/albums/v55/PrestoTuna/2012-02-25192608.jpg
My problem is the bolts for the axle hit the bolt head on the endlink a tad. A few minutes with a bender I no longer have would make me happier. Be aware that shortening the links will cause the bar to raise in the front, hitting the floor more.
Rakuny
02-25-2012, 11:03 PM
OK, just went to the garage, threw the stock arms on the subframe, and bolted in the Addco sway bar. Few things I found:
1. extend your adjustable control arms so they are not bottomed out, just a few turns is enough. I don't know where these will end up after an alignment, but I can definitely see where this can limit my neg camber in the back.
2. adjust the lower arm camber to full positive (both bolts toward each other/center). After installing the links this car be adjusted back maybe.
3. bolt the bar to the subframe loosely, turn the endlinks a couple turns onto the lower control arm, Then insert the connecting bolt from the link to the bar, I had the entire bar bolted in 10 minutes once I sat there for a bit looking how everything went together. Cleared the axles...barely.
So far without the subframe being on the car I spotted a few issues. One being the links are a bit too long, the other is that the bar total width and arm length is wrong causing the links to be on the wrong side of the bar. This is the entire issue with this bar, 1" or less arm length (would affect the stiffness of the bar, I'll measure it and see exactly what this bar is to start) and a couple degrees change in the arm bend and this install would be cake.
To Jeremy: There's plenty of room for droop, I can attach the bar to the bottom of the lower arm if I wanted.
Pics will be had once I'm cleaned up. Without the subframe in the car it's a whole 'nother thing than trying to install it in the car, but so far I'm thinking it'll bolt in fine until I find another issue.
Thank you!
Rakuny
02-26-2012, 06:11 AM
I was also thinking about making some spacers, like this...
http://www.supercar-engineering.com/rubberducky/3S/Mods/TT/RSwBar/Image19.jpg
B-Man
02-26-2012, 11:59 AM
Imagine it's just think sidewalled tubing. Looks so close you might be able to use washers.
anyonebutme
02-26-2012, 12:22 PM
The endlink is not going to push the bar away, you'll just push the endlink to more of an angle. Spacers would be part of the fix if you threw the bar in a bender to spread it a little away from the flange.
anyonebutme
02-26-2012, 01:59 PM
http://www.supercar-engineering.com/rubberducky/3S/Mods/TT/RSwBar/Image24.jpg
See how short the endlinks are on the Saner
Rakuny
02-29-2012, 07:49 PM
finally started feeling better today so I dropped the subframe back out (so I can hammer the floor) and took the links off. Should I cut them to the line or leave them a little longer?
anyonebutme
02-29-2012, 11:07 PM
I haven't worked on mine lately, I'd cut it as short as possible, the line looked way to convenient to me, so that's where I'd start if I was cutting it, lol. Depending on what tools you have at your disposal, but I'd first cut it a little long of the line, and work from there.
Rakuny
03-06-2012, 08:39 PM
hmm, well I cut about half way between the end and the line and then leveled it off. It fits and it clears, it's still really close but I think once I get it aligned it will be more even on each side. I didn't hammer the floor back enough so I need to get something that I can hammer around the sway bar into the floor with to make more clearance.
B-Man
03-06-2012, 10:19 PM
:worthless:
Rakuny
03-07-2012, 08:31 AM
I didn't bring the camera with me yesterday, I'll take some today.
Rakuny
03-07-2012, 07:15 PM
ok, pics..
passenger side link
http://img849.imageshack.us/img849/6072/1002948o.jpg (http://imageshack.us/photo/my-images/849/1002948o.jpg/)
drivers side
http://img39.imageshack.us/img39/7426/1002952.jpg (http://imageshack.us/photo/my-images/39/1002952.jpg/)
this one looks like it doesn't clear, I couldn't get the camera higher because the shock is in the way. the link is low enough that it does clear, I'm hoping the alignment will even this out with the other side.
Wide shots
http://img269.imageshack.us/img269/1948/1002956q.jpg (http://imageshack.us/photo/my-images/269/1002956q.jpg/)
http://img809.imageshack.us/img809/1354/1002955w.jpg (http://imageshack.us/photo/my-images/809/1002955w.jpg/)
EDIT: big thanks to you ABM
B-Man
03-07-2012, 08:02 PM
How'd you reflatten the ends?
Rakuny
03-07-2012, 10:12 PM
How'd you reflatten the ends?
Well I cut it with a cutting wheel and it wasn't perfect so I just eyeballed it with a grinder the best I could.
hated
03-11-2012, 01:08 AM
So these don't fit from the factory or is there somethign with your car? Cutting it required for fitment?
J. Fast
03-11-2012, 12:39 PM
They fit, you have to use shorter end links or cut the end links down... and BFH the floor at the tunnel. Pretty simple list of modifications considereing the benefit.
deemo99
05-10-2012, 10:48 PM
Tried to see if mine would fit without said BFH and..................gonna drop the subframe again and BFH the tunnel. Not sure yet on the endlinks, but it sure seems like the bends are too far apart in the portion of the bar that is over the driveshaft. The fix should be fairly easy, but kind of disappointing that the fit sucks.
If you're on the fence like I was re the tunnel I'd recommend going the BFH route to start with.
deemo99
05-13-2012, 12:08 AM
I milled .500 off of the endlinks on the Bridgeport today and the rear bar fits, barely. I will try to get a pic, but had to grind a small flat on the DS end of the sway bar to clear the hub bolts, the bar can still rub, but only if you dukes of hazzard the car over a cop car:) Once the control arm is up even just .25 inch, all clear.
Next PITA issue will be the brake lines. One came apart easy, but planning to cut, re-flare, etc to get the stainless lines in.
If you have Addco bars not installed yet, I'd recommend going the BFH and cut the endlinks route as I mentioned above and as others have indicated as well. 3SX must have a magic car since theirs apparently installed with no extra mods required. Addco could have made a better product, in my opinion, at least in terms of the fit. Can't wait to see if the bar works better than it fits (as it comes out of the box).
I don't know how to work in the garage with out the rear subframe to trip over!!!!
knighty
06-10-2012, 05:32 AM
Will the Addco clear a PST 1-piece CFDS?
I have my subframe out for cleanup (AWS delete, too). I know what you mean about tripping over the subframe... And the transmission.. And driveshaft, complete exhaust, transfer case, pickle forks, axles, and etc., etc.
I've heard the Saner does not clear a 1-piece...
Rakuny
06-15-2012, 05:25 PM
Your guys end links really don't hit the axle nuts after shortening them? mine were hitting so I re-shortened them to the line, had to cut the bolts shorter too.. they cannot go shorter unless I cut the bushings shorter. If I apply more than half throttle it hits, hard.
anyonebutme
06-15-2012, 07:01 PM
I need pics, to my knowledge mine do not hit at all, I'll be under the car in a few minutes and I'll recheck everything. What is your ride height?
Rakuny
06-15-2012, 07:20 PM
heading out to take some pics now, I have a 4 finger gap in the rear
Rakuny
06-15-2012, 07:49 PM
http://img404.imageshack.us/img404/6867/dscn0454g.jpg (http://imageshack.us/photo/my-images/404/dscn0454g.jpg/)
http://img269.imageshack.us/img269/1448/dscn0455rx.jpg (http://imageshack.us/photo/my-images/269/dscn0455rx.jpg/)
http://img542.imageshack.us/img542/8194/dscn0457x.jpg (http://imageshack.us/photo/my-images/542/dscn0457x.jpg/)
Rakuny
06-15-2012, 08:43 PM
NVM, it's driveshaft vibration :(
My assumption is that the delrin bushings I bought don't space it like stock and it throws it off... putting stock back on tomorrow
Checkered vr4
06-17-2012, 11:51 PM
http://img404.imageshack.us/img404/6867/dscn0454g.jpg (http://imageshack.us/photo/my-images/404/dscn0454g.jpg/)
http://img269.imageshack.us/img269/1448/dscn0455rx.jpg (http://imageshack.us/photo/my-images/269/dscn0455rx.jpg/)
http://img542.imageshack.us/img542/8194/dscn0457x.jpg (http://imageshack.us/photo/my-images/542/dscn0457x.jpg/)
Sorry for being off topic but are those Evo rear strut adapters possibly upside down?
Rakuny
06-17-2012, 11:55 PM
You can mount them either way
EDIT: I was right about the DS vibration and how to fix it, everything is all good.
knighty
06-19-2012, 03:28 AM
Rakuny, so the delrin bushings you mention were sway bar bushings or ... ? Which bushings were causing the issue?
anyonebutme
06-19-2012, 09:08 AM
the driveshaft carrier bearing bolt bushings.
Rakuny
06-19-2012, 09:46 AM
Yah, I was able to create a spacer (alright a washer stack if I'm honest...) for the delrin bushings and keep them on... it only throws it off on the rear carrier bearing as the fronts don't space it down. The rear do and both sides are not the same. Luckily I still had the old bushings, something I learned is to NEVER throw stuff away. Saved my ass many times.
knighty
06-19-2012, 02:00 PM
Yah, I was able to create a spacer (alright a washer stack if I'm honest...) for the delrin bushings and keep them on... it only throws it off on the rear carrier bearing as the fronts don't space it down. The rear do and both sides are not the same. Luckily I still had the old bushings, something I learned is to NEVER throw stuff away. Saved my ass many times.
Oh. I have no such thing on my car. I still need to find out if the Saner or Addco will work w/ a 1-piece DS. Crap. *The search continues*
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.