PDA

View Full Version : 300+ hp base model what supporting mods do I need?



hemp
12-16-2011, 02:46 PM
I have a 99 base 3000gt and the stock 161 hp is not enough for me. I'm planning to add a 100 shot of direct port nitrous, headers, intake, exhaust, and a few other goodies to hopefully bring it up past 300 hp. What kind of injectors or fuel pump will I need?

Vantage
12-16-2011, 03:15 PM
Are you against TT'ing it for some reason?

http://www.3sx.com/store/cars-3sx/cars-eric.asp

Eric hit 225hp with his Stealth, and has a lot done to his motor. You will never see over 300 all the time with just all motor. You need boost, or you'll only ever get the power your wanting when you turn on the juice, which I guess it seems like your ok with.

hemp
12-16-2011, 03:41 PM
I never said All motor with nitrous and I"m aiming for 300 crank not to the wheels I'd be happy with 250 to the wheels ....

mb3000
12-16-2011, 06:02 PM
The stock TT injectors should be good (360cc) as well as a Walbro fuel pump.

stealthee
12-16-2011, 06:22 PM
Don't even waste your money on trying to get 300 hp on a SOHC. If you want more power, go TT.

And no I am not dogging on a SOHC because I own one myself. The highest HP SOHC puts down a little over 200 hp to the wheels and he has over $12,000 into the engine alone.

FeaRpb
12-16-2011, 06:30 PM
Agreed with Stealthee

BigTyla
12-16-2011, 07:12 PM
Supporting mods? A VR-4. You will regret spending $10k on a SOHC to get it as fast as a stock VR-4 with less reliability.

Jeremy C
12-16-2011, 07:14 PM
I've never really looked into the SOHC motors - the blocks are still identical to DOHC NA's aren't they? Wouldn't be too hard to swap to the DOHC rotating parts and boosting it, and would cost far less than trying to build up the SOHC.

Or am I totally up the wrong tree here? I'm really rusty when it comes to modding the 3S's I don't own.

stealthee
12-16-2011, 07:23 PM
The bare block is the same but you have to change EVERYTHING. Besides, stock DOHC ECU and harness are totally different than SOHC harness so thats another issue. Might as well throw an entire TT engine, harness and ECU in and go that route. The most diffifcult part of the conversion on a SOHC is figuring out how to wire up the alternator, because the DOHC alternator harness is in the body harness, the SOHC alternator harness is in the engine harness.

IPD
12-16-2011, 09:22 PM
i STILL say someone with the expertise (and know how) should keep the sohc longblock intact & just modify the tt manifolds to run on it with 9b's. still use SOHC plenum, tt SMICs, SAFC2 & an MBC. only need a custom y-pipe to fit the SOHC plenum.

stealthee
12-16-2011, 09:30 PM
And I still tell you someone with the expertise tried is and it was deemed as undoable.

green-lantern
12-16-2011, 11:46 PM
Don't even waste your money on trying to get 300 hp on a SOHC. If you want more power, go TT.

And no I am not dogging on a SOHC because I own one myself. The highest HP SOHC puts down a little over 200 hp to the wheels and he has over $12,000 into the engine alone.

This!!!!!!!!!!!!

I know the guy he is talking about.

green-lantern
12-16-2011, 11:50 PM
Use that car as a DD then get a VR4 to kick ass in.

hemp
12-17-2011, 01:23 AM
^ Can't this is my one and only ride. Why would getting nitrous be a waste? It's under a grand for the whole kit and installation is fairly straightforward.

Boomer3000
12-17-2011, 02:27 AM
Ok, be smart... Nitrous is only good for so much, the more you throw at it, the harder it will be on the motor.

Your options

1) Do what you want, dump a bunch of money into a sohc base and never be satisfied
2) Do the swap, still not be happy with it, or spend an ass load of money and be happy/maybe
3) Buy a TT, mod it and be extremely happy-when its running lol

We are all trying to help you and to keep you from making mistakes that others have made, and to keep you from wasting time and money. But its up to you, your car your choice.

I found my TT for 600 bones, dumped a little over 1200 into it and bam, I can dd my car every day if I wanted to. Not to mention 170xxx on the stock drive train.... Not trying to be a dick, just food for thought.

arm0red1
12-17-2011, 04:54 AM
That and with nitrous, your still slow as balls without the juice, not to mention you need to find a place to fill a bottle regularly if you plan on using it, swapping to a stock twins setup will snag you just as much if not more power on tap whenever you want and only limited by your gas gauge or the po-leece. Nos is cool and all bro/dawg/playa/ Mr. Deisel, but you can snag a full tt swap for 600 bucks, hell, ive got evrything minus the turbos you need off my tt in my garage....

stealthee
12-17-2011, 09:46 AM
^ Can't this is my one and only ride. Why would getting nitrous be a waste? It's under a grand for the whole kit and installation is fairly straightforward.

Well lets see. Nitrous isn't always on tap, like boost is. Sure you can get the kit and have it installed for under a grand but do you realize how much it costs to get a tank filled? You are talkling about $4 a pound or so. Haven't checked the cost lately. So if you get a 10 lb tank you are spending $40 to refill. And a 10lb tank is only going to get you about 4 "runs" per fill.

That "extra 100 hp" is going to cost you a METRIC SHITTON more than doing a TT swap.

And you say this is your one and only ride. That is all the more reason to just DD the car and enjoy it for what it is. If it automatic, swapping to 5 speed would be the best bang for the buck gain you could ever imagine. The change in gearing changes the feel of the car.

I have made the mistake of trying to go too far on a DD and paid the price dearly for it. Save your money, drive your car, and buy something that is faster out of the box.

dsmnoob91
12-17-2011, 06:31 PM
Agree^ I put about 500 miles on my car this past year I tried to dd it after making it TT and hopped timing bought a brand new car for dd and fixed my 3kgt and now I am building a motor painting it and making it the way I want it for next year and of you plan on using nitrous all the time be ready to melt a piston had it happen to me and I had a built motor na is a waste of time if you ask me to go fast in unless it's a ls1 or a v8 them you can make it quick

hemp
12-18-2011, 12:35 AM
^ Eh everyone's idea of quick is different I don't need a v8 or ls1 for my car to be "quick" in my opinion. Decisions decisions ...

dsmnoob91
12-18-2011, 04:06 AM
Wait so is yours auto or 5speed?

IPD
12-18-2011, 08:51 AM
^ Eh everyone's idea of quick is different I don't need a v8 or ls1 for my car to be "quick" in my opinion. Decisions decisions ...

sell it and buy a vr4. the damn things are so piss-poor-cheap these days there's ZERO excuse not to do it.

arm0red1
12-18-2011, 11:06 AM
That and being "quick" for all of 4-6 seconds for when you hold down the button and empty the bottle isnt quick by definition of the majority. Hell a tt conversion can be had for as cheap is not cheaper than most of the wet zex, nxpress, edelbrock, nos kits brand new.

hemp
12-18-2011, 11:47 AM
5 speed I might do stage 2 clutch and lightweight flywheel when I get my transmission worked on sometime.

stealthee
12-18-2011, 11:54 AM
No need. A clutch doesn't gain you any horsepower. You only need enough clutch to hold the power you make. And I despise the feel of a lightweight flywheel. Anda again, its not a power adder so you are wasting your money if you want to go faster.

dsmnoob91
12-18-2011, 01:21 PM
Yeah of it's not slipping won't make a difference at all

Emilie@GZP
12-18-2011, 01:23 PM
^ Can't this is my one and only ride. Why would getting nitrous be a waste? It's under a grand for the whole kit and installation is fairly straightforward.

If it is your only ride, then nitrous is the LAST thing you want to start playing with.

IPD
12-18-2011, 02:17 PM
i smell another 3/s in the junkyard....

hemp
12-18-2011, 02:21 PM
Doesn't the lw flywheel lower drivetrain loss though so more power gets to the wheels? How can a lightweight crank pulley add power but a lw flywheel doesn't?

IPD
12-18-2011, 03:56 PM
Doesn't the lw flywheel lower drivetrain loss though so more power gets to the wheels? How can a lightweight crank pulley add power but a lw flywheel doesn't?

the IDEA is that in theory. technically, less rotating mass should = less power loss. problem is, you use more than one gear. each time you shift, that lighter rotating mass will slow down faster because it has less inertia. this effect is not only annoying, it effectively eliminates nearly all of the benefit of the LW flywheel.

a LW crank pulley is another joke. again, if you've got nothing else to blow money on, and your car is making piss-poor power numbers, then a LW pulley might be for you. they're not good for high HP engines. fact is, with how piss-cheap tt-conversion parts are, a LW pulley & a LW flywheel--brand new--will set you back nearly the same amount as the parts for the conversion.

it still amazes me after all these years that people approach this platform as though it's another SBC. this platform sucks as n/a--if you want power goals. if all you want is a reliable dd, n/a is great. that's the long and short of it.

dsmnoob91
12-18-2011, 09:35 PM
Throw some nice wheels on it lower it call it a day

stealthee
12-18-2011, 09:56 PM
The onyl way to effectively lower a SOHC is with coilovers.

green-lantern
12-18-2011, 10:10 PM
Throw some nice wheels on it, lower it, call it a day


The onyl way to effectively lower a SOHC is with coilovers.

OK read it now :p

BTW I didn't know that extra cam weighed that much ;)

hemp
12-18-2011, 10:21 PM
What's a good brand for coil overs might be something I might look into.

stealthee
12-18-2011, 10:23 PM
Megans

Emilie@GZP
12-19-2011, 07:34 PM
Doesn't the lw flywheel lower drivetrain loss though so more power gets to the wheels? How can a lightweight crank pulley add power but a lw flywheel doesn't?

lightweight flywheels suck for daily driving, in all honesty. You are much better off with a factory flywheel.

arm0red1
12-20-2011, 12:22 AM
^^ troof, they make it a HUGE hassle for driving and shifting. Your revs fall off too darn quick to revmatch effectively for daily use. It'll be like learning stick all over again. Not to mention the car will have a tendancy to stall a little easier when you let out the clutch due to lack of inertia. It's great if your WOT, otherwise its annoying and crappy as your car becomes more "on/off" - my talon had that in it with a larger TB- such a pita to drive around in, it was so jerky.

hemp
12-25-2011, 10:51 PM
I drove my friends Focus svt with lightweight flywheel and it wasn't bad. I also found some lighter weight steel ones on 3sx that are not aluminum. Anyways I got beat off the line bad by a Nissan Murano today. No surprise they run 15.4 @ 93 somehow in that heavy suv. DAMN.

IPD
12-26-2011, 12:35 AM
I drove my friends Focus svt with lightweight flywheel and it wasn't bad. I also found some lighter weight steel ones on 3sx that are not aluminum. Anyways I got beat off the line bad by a Nissan Murano today. No surprise they run 15.4 @ 93 somehow in that heavy suv. DAMN.

CVT means the wheels are being powered for the full 1/4...no shifting pauses.

R/T93
12-26-2011, 01:15 AM
^^ troof, they make it a HUGE hassle for driving and shifting. Your revs fall off too darn quick to revmatch effectively for daily use. It'll be like learning stick all over again. Not to mention the car will have a tendancy to stall a little easier when you let out the clutch due to lack of inertia. It's great if your WOT, otherwise its annoying and crappy as your car becomes more "on/off" - my talon had that in it with a larger TB- such a pita to drive around in, it was so jerky.

I have found all of that to be untrue with my 93 n/a. Revs fall super fast but it makes for quick, proper shifts. I have stalled the car like 3 times ever with it. Noticed zero difference between stock and the fidanza except quicker revving.
Perhaps I expect the engine to react differently than some but I can't stand these new cars where if you rev them at idle it takes 5 seconds to drop all the way down

Boomer3000
12-26-2011, 02:28 AM
Stick a couple potatoes between the flywheel and clutch.... Then when you power shift........Bam French fries on the go.

MC#4
12-26-2011, 05:01 PM
SOHC motors can and have made impressive power. I don't know of any real SOHC heavy hitters in the 3S world but there are a few in the turbo dodge/turbo mopar world. The most prominent one I know of is Ondonti, He ran 11.50's with a 3.0 SOHC 12v (same motor as in the base 3S) in a duster. He was pushing 500+whp if I remember correctly. Couple of guys have thrown a single turbo on thier SOHC and run the piss out of them. I don't think I'd ever build a SOHC 3S since the TT option is so incredibly easy, but it's really not that far out there to make a lot of power with a SOHC.

GreatDepressionRace's Channel - YouTube (http://www.youtube.com/user/GreatDepressionRace?blend=3&ob=video-mustangbase)

stealthee
12-26-2011, 05:40 PM
Ondonti was a regular poster on 3si, so we know of him.

And you are right, being the TT is such a viable option not many people really push the SOHC in the 3s world. sunmind has a ton of money in his NA SOHC making something like 220whp. I quit buying "power mods" for my SOHC a long time ago. Running mid 15's is respectable considerng the car. With better launches I'd had been limited to a 15.2 or 15.3 simply due to gearing.

GTwizard
02-01-2012, 02:30 AM
Been gone for a while. So just a quick review. I saw a question about the blocks. A SOHC and DOHC are not the same. There are no mounting bosses for the hydraulic tensioner.
If you could get 300 crank, might just feel like this. LOL.


http://www.youtube.com/watch?v=2s0I3tnGGmg