PDA

View Full Version : Wheel Speed sensor



$$$PIT
11-13-2011, 06:45 AM
I've been tryin' to remove mine for the past hour. I was told that all you had to do was remove the bolt and it would "pop right out". Well, mine is rusted to hell and back. Do you have to remove the caliper and rotor? I'm beginning to think that there's a clip or somethin' on the inside I wasn't told about. Anybody that has done this give me a little hint please. Thanks

OhioSpyderman
11-13-2011, 09:10 AM
It IS rust.

Apply as much penetrate as you can and work slowly. They are easy damage if you use the wrong tool and pry....

Bob.

$$$PIT
11-13-2011, 09:15 AM
Guess I'll have to get a NEW can of PB Blaster. The one I have is almost gone. :( I was trying not to pry too much on it anyway.

Would it hurt to twist it? If I even can.

OhioSpyderman
11-13-2011, 09:23 AM
Be careful not to "crush" it with whatever you use to try!

Bob.

$$$PIT
11-13-2011, 09:33 AM
I got the side "away" from the dustcover loosened about a 1/4 inch. I was afraid there was somethin I had missed holding it from the other side so I quit. I'll go back to work on it some more

TwIzTeD_3kGt
11-13-2011, 09:40 AM
Good luck. I've removed them from rusty holes by turning back and forth, but I've also broken them with that same method. Most important thing is to take your time and be careful if you really need to save the sensor.

$$$PIT
11-13-2011, 09:46 AM
The reason I'm even tryin' to get them out is to clean them. Coz my ABS is engaging during normal braking. It is also causing the idle to rise to 2k until I get down to about 10 mph.

stealthee
11-13-2011, 10:54 AM
Disable the garbage ABS and make life a lot less stressful.

If you are still insistent on removing and cleaning the sensors, just keep at it. One time it took me two hours to remove a sensor from a parts car.

$$$PIT
11-13-2011, 03:30 PM
I've already pulled the relay for it. But, the idle goin up to 2K above 10mph is what's botherin me

Primus101
11-13-2011, 04:38 PM
My TT was just recently doing the exact same symptoms. The only way I temperarily corrected it was to unplug the ABS module, located behind the rear passenger side panel. Easy enough to try as you only have to unhook the front of the panel for access-you dont have to fully remove panel. try it-

$$$PIT
11-13-2011, 07:02 PM
THAT might be easier than pullin' these sensors. But I wonder if that will fix the idling up issue

stealthee
11-13-2011, 07:07 PM
I dont think the idle up issue has anything to do with ABS. You may have a vacuum issue with the booster.

Primus101
11-13-2011, 07:11 PM
Yes, that fixed the high idle issue for me (2k rpm) the problem would come & go-ABS light would stay on when problematic.

$$$PIT
11-13-2011, 07:18 PM
Yes, that fixed the high idle issue for me (2k rpm) the problem would come & go-ABS light would stay on when problematic.

That's what mine is doin'. But since I pulled the relay, it does it all the time. Even when I don't hit the brake. But idles down when I get down to about 10mph.

Primus101
11-13-2011, 07:28 PM
The ABS module raises the idle to compensate for engine braking- sorry, cant figure out how to copy & paste it from the FSM, but there is info in the '91 Stealth manual page 5-31
I attempted to pull the relay & fuse to no avail- only when I unplugged the module did it correct itself. Takes like 5 minutes to get to & unplug, try it & thank me later....that high idle just about drove me nuts!

$$$PIT
11-13-2011, 07:34 PM
The ABS module raises the idle to compensate for engine braking- sorry, cant figure out how to copy & paste it from the FSM, but there is info in the '91 Stealth manual page 5-31
I attempted to pull the relay & fuse to no avail- only when I unplugged the module did it correct itself. Takes like 5 minutes to get to & unplug, try it & thank me later....that high idle just about drove me nuts!

I will.

Primus101
11-13-2011, 07:51 PM
Hmmm, just read now the idle increase for ABS applies to AWD- You're FWD?

$$$PIT
11-13-2011, 08:24 PM
I have 1 of each. :) This is for the VR4.