View Full Version : How to: repaint a damaged body panel
BigTyla
11-10-2011, 01:09 AM
A few months ago my Honda Fit was hit in a parking garage (while parked...LOL) by an immigrant with no car insurance. The damage she did to my car was just barely over my deductible, and my insurance company could not guarantee they could get all of the money back since she was rather poor and technically not legally obligated to pay since the wreck occurred on private property. As a result, I decided to repair the damage myself.
I've heard some good things about the Duplicolor touch-up spray cans so I decided it was worth the $8.00 investment to give it a shot. So with 400-grit sandpaper in hand, I started sanding down the damage.
Here is a picture of the damage:
http://i7.photobucket.com/albums/y265/tylerw53/003-2.jpg
Here is where the brunt of the damage was done. In the second picture you can clearly see the paint rippled around the edges.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0135.jpg
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0137.jpg
The scratches on the left are not very deep and can be easily sanded out. If that were the only damage, a repaint wouldn't even be required. That would just be wetsanded and then polished since this is a single-stage paint. The rest of the damage needs to be leveled out and feathered into the undamaged paint. A rule of thumb here is to get rid of the jagged edges. Your repair spots should be rounded out and the surface where the damage ends and the undamaged paint begins should be completely smooth. If you feel even the slightest ripple, keep sanding! Prep is 99% of a good paint job. You can see the result of a good sanding job in the next photo.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0139.jpg
And here is a picture of all of the spots repaired.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0141.jpg
It should be noted that this entire sanding process took me about 1.5 hours. That's how much time you'll need to dedicate to damage like this if you want your repair to look presentable. Following posts will show how to apply the spray paint and, if necessary, blend the new paint with the old paint.
BigTyla
11-10-2011, 01:10 AM
When your surface is fully sanded, you can mask off the area you need to paint. Once you get your area masked off, you need to clean the area with rubbing alcohol to prep the surface for paint. Use painter's tape and some newspaper to cover surrounding areas to keep overspray from getting on areas you don't want it to be. Wait 30 minutes after applying the rubbing alcohol before painting.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0144.jpg
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0145.jpg
When applying the paint, you have to make VERY light passes. If you apply too heavy of a coat at once, the paint WILL run. I made very light passes and STILL got runs in the paint. That's just what you have to live with when spraying from a can. You will need to make at least three passes for this to work properly. If your damage is heavy enough, such as in my case, you will have to make up to ten passes. I made eight before I finally got full coverage.
Here's the result of one light coat.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0149.jpg
Here's the result of eight coats. This provides full coverage.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0150.jpg
Notice the slight runs in the paint. Those will have to be wetsanded out.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0152.jpg
BigTyla
11-10-2011, 01:10 AM
For the next step, you're going to need the following materials:
-Turtle Wax liquid rubbing compound
-1000, 1500, and 2000 grit automotive sandpaper
-Tape
-Buffer
-Spray bottle with water
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0194.jpg
After you let the paint dry for a couple of days you can remove the tape. This is what your repair area should look like.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0181.jpg
Notice the sharp lines where the new paint was applied. Those lines are raised and need to be sanded down and blended with the paint around it. Tape up your area again, this time placing the tape a couple of inches from the edges of your new paint.
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0183.jpg
Spray the area liberally with water from your spray bottle. Take your 2000 grit sandpaper and begin working it around the edges to sand it down, drying intermittently and applying more water. Apply as little pressure as possible. You want to sand a little past the edges to try to blend the old and new paint. If you applied many coats like I did, you might find that the more aggressive sandpaper is better for your application. In my case, I ended up using 1000 grit on the edges and then moved to 1500 grit. After taking care of the edges, sand the entire area with 2000 grit. When you are done, the area should look like this:
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0184.jpg
Notice the dark portions along the bottom where too much paint was sanded. This is okay! You'll cover this again when you apply more paint. More paint?!?! Yes, more paint. Remove the tape from the body and apply new tape about four inches from the edges of the new paint and mask the surrounding area with paper to avoid overspray. This will allow us to apply the paint outside the hard edges to more effectively blend in the new paint with the old paint. Lay a light coat of paint within the area. When you get outside the sharp edges we sanded down, feather the spray paint out slightly. Do not go all the way to the inner tape edge. Wait 10 minutes, then come back and repeat the process. Wait 30 minutes and remove the tape and masking material. Let it dry overnight.
When you come back to the repair the next day, you should see some improvement over the first time you laid paint. In particular, the hard edges where old paint meets new paint should be much harder to see, but if you look hard enough you will likely still be able to notice them. This time, break out your 2000 grit sandpaper, spray the area with water, and sand the whole area again. After sanding, the area should look like this:
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0197.jpg
If you look VERY closely, you might be able to pick out some very slight lines where the paint doesn't blend perfectly. This next step ought to take care of that. Take out your buffer and rubbing compound. Apply a quarter-sized amount of rubbing compound to your buffer pad and rub it around the repair area. Turn the buffer speed up to 1000 rpm and run the buffer across the repair area in an "S" motion, taking care not to spend too much time in one area. Let the buffer do the work! If you apply too much pressure, you'll burn right through the paint. The entire buffing process should take 45 to 60 seconds. Afterward, wipe the area with a clean towel. If your original paint was a base coat/clear coat finish, you'll need to apply some Duplicolor clear coat over the new paint the same way you applied the paint. Do two light coats. My car's original finish was a single stage paint, so I did not apply a clear coat. Now take your favorite wax and use it on the entire repair area. I used Meguiar's Cleaner Wax paste. And here's your finished product:
http://i7.photobucket.com/albums/y265/tylerw53/IMG_0198.jpg
I'm pretty happy with my results. From afar the car looks like nothing happened at all, but if I look close enough I can still see very slight lines where the old and new paint were still not completely blended. You can see it in the picture above if you look hard enough. More patience with sanding and buffing ought to take care of this. Overall, it looks great for an investment of $10 and about four to five hours of my time.
stealthify
11-10-2011, 01:30 AM
In for the final results. Looking good so far man!
Greg E
11-10-2011, 02:10 AM
Also in for results!!
Boomer3000
11-10-2011, 03:17 AM
Subded
IronmanTT
11-10-2011, 10:34 AM
:stupid: with all them above...
wingnut
11-10-2011, 11:47 AM
A few months ago my Honda Fit was hit in a parking garage...my insurance company could not guarantee they could get all of the money back since she was rather poor and technically not legally obligated to pay since the wreck occurred on private property.
...am i the only one scratching my head over this one?!?
FeaRpb
11-10-2011, 12:10 PM
I am here!
OhioSpyderman
11-10-2011, 12:35 PM
Looking Good Tyla :)
Also in for results...
Bob.
BigTyla
11-10-2011, 12:38 PM
...am i the only one scratching my head over this one?!?
Trust me, I'm still scratching my head. I was very frank with the agent that gave me my estimate when I was told that, and he thought I was mad at him! I assured him I was not, but was appalled at that information. He said something similar happened to him a year ago and he ended up having to foot the bill!
I won't even begin to get into the moral implications of this beyond stating that, by definition, this lady could have driven around and hit every car in the parking lot and would not have been required to pay a dime! And yet we responsible citizens who get insurance as mandated by law are required to foot the bill for someone else's carelessness!
/rant
EDIT: BTW, I could have gone to small claims court to get her to pay, but this happened 6 hours away from home, so it would not have been in my best interest to do so.
mcshooter
11-10-2011, 01:50 PM
if you have a paint gun this is a easy repair, clean it, scratch it a spray a primer sealer. spray3 coats of base and 3 coats of clear. it used to be you had to use a blender asap but there is a new blender that comes in a spray can and can be used up to 12 hours later. i think it is a upro product. .. this will keep you from having to repaint the whole part.
BigTyla
11-10-2011, 03:34 PM
if you have a paint gun this is a easy repair, clean it, scratch it a spray a primer sealer. spray3 coats of base and 3 coats of clear. it used to be you had to use a blender asap but there is a new blender that comes in a spray can and can be used up to 12 hours later. i think it is a upro product. .. this will keep you from having to repaint the whole part.
There are multiple clear coat blenders on the market. DuPont and Sherwin-Williams brands seem to be the most popular.
Repairing with a paint gun is always the best option! It is an option that I have but I chose this route due to cost, ease of repair, and documentation for those that do not have those resources. Plus I was curious myself on the effectiveness of these Duplicolor products.
futurevr4man
11-10-2011, 04:25 PM
well dang it, fill in with more info!!
BigTyla
11-11-2011, 02:11 AM
Ask and ye shall receive. Part 3 will come next week. I need to give the paint a couple of days to cure before wetsanding.
futurevr4man
11-11-2011, 10:16 AM
noice!
Emilie@GZP
11-11-2011, 11:47 AM
Did you prime over the exposed plastic??....
DrGonzo
11-11-2011, 12:17 PM
Did you prime over the exposed plastic??....
Curious on that also.
Had issues in the past trying to get the Dupont to bond to bare plastics. Ended up having to strip it all of, use an adhesive promoter, prime and then spray in order to get a good bond. Also be sure that the paint has a flex additive so that the paint does not crack when the bumper flexes.
Chris@Rvengeperformance
11-11-2011, 12:18 PM
bulldog adhesion promoter on the bare plastic
BigTyla
11-11-2011, 12:55 PM
Great question. Actually, the bare sections you see aren't bare. That black stuff is actually rubberized primer applied as an undercoat out of the factory for the Fit since their front and rear bumpers are so flexible. I decided not to use another primer over this, but it might have helped me not have to use so many coats to get full coverage!
For bare plastic, you should use an adhesion promotor, then primer, and then apply the paint.
Boomer3000
11-13-2011, 04:56 AM
looking good
BigTyla
11-14-2011, 10:46 AM
I'll be wetsanding the vehicle tonight. I'll post photos of the results tomorrow.
BigTyla
11-15-2011, 11:56 PM
Post #3 updated with blending results!
stealthify
11-16-2011, 01:03 AM
Impressive work Tyler, you make it look so easy.
It might seem like a dumb question, but are you planning on clear-coating?
BigTyla
11-16-2011, 01:12 AM
Impressive work Tyler, you make it look so easy.
It might seem like a dumb question, but are you planning on clear-coating?
Under normal circumstances I would, but Taffeta White on the Fit is a single-stage job, so to be consistent I will not be applying a clear coat. I should edit the post to clarify this.
stealthify
11-16-2011, 01:25 AM
Under normal circumstances I would, but Taffeta White on the Fit is a single-stage job, so to be consistent I will not be applying a clear coat. I should edit the post to clarify this.
Got it, thanks for clarifying. Your tutorial makes me want to go give it a try.
Boomer3000
11-16-2011, 04:50 AM
ok.. so say you were going to use clear, what would you use??
futurevr4man
11-16-2011, 09:37 AM
well done! good write-up
BigTyla
11-16-2011, 11:47 AM
ok.. so say you were going to use clear, what would you use??
Use the Duplicolor clear coat that comes in the can like the touch-up paint.
AdamVR4
11-16-2011, 12:39 PM
Wow, nice work.
Damn, Tyler...that's nice.
Roybatty
11-16-2011, 02:14 PM
Thanks for sharing. Wasn't aware of how to blend by moving the tape out away from the original and painting again. Looks great...will definitely try this.
Does anyone have a source for paint for our cars (Firestorm Red RA8)? They don't have it @ your local hardware stores, found some websites but looking for others experience/input.
BigTyla
11-16-2011, 02:51 PM
Thanks for sharing. Wasn't aware of how to blend by moving the tape out away from the original and painting again. Looks great...will definitely try this.
Does anyone have a source for paint for our cars (Firestorm Red RA8)? They don't have it @ your local hardware stores, found some websites but looking for others experience/input.
I've heard Automotivetouchup.com Touch Up Paint, Aerosol Spray Paint and Touchup Paint Accessories | AutomotiveTouchup | 888-710-5192 (http://www.automotivetouchup.com) is a good source for touch-up paint if Duplicolor doesn't carry what you need. They carry touch-up spray cans, pens, and spray cans. Here's a link for Firestorm Red:
1992 Dodge Stealth Touch Up Paint Colors (http://www.automotivetouchup.com/choosecolor/choosecolor.aspx?year=1992&make=Dodge&model=Stealth)
BigTyla
11-30-2011, 04:23 PM
Update: My wife and I traded in the Fit to the dealership last week for another vehicle and they didn't even notice that the vehicle had any repairs done, so that is definitely a testament to how well this process works if you just take your time and do it right. For a $10-20 investment you really can't beat this if you don't have access to a compressor and spray gun.
Update: My wife and I traded in the Fit to the dealership last week for another vehicle and they didn't even notice that the vehicle had any repairs done, so that is definitely a testament to how well this process works if you just take your time and do it right. For a $10-20 investment you really can't beat this if you don't have access to a compressor and spray gun.
Hear, hear...
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.