View Full Version : Help identifying my turbos...
AWDER
11-05-2011, 03:56 AM
So, I bought this car with a few of the mods already done and have added a few myself. I pulled the intake pipe off the front turbo before and did not think much of it. Well I saw the inlet of a DR500 and I honestly did not realize they used the "b"series compressor wheel style until now. Just hadn't seen one before I guess, that and I am pretty new to the platform anyway. (own a BW S366 powered DSM also)
Well, I pulled the inlet off my front turbo and took a couple pictures. I could not visually see in person nor feel any sort of taper or lip in the inlet. I have been told the stock 9b has an obvious taper in the inlet and have seen pictures. These are a couple of the pictures, just wondering if I got lucky with a little bigger than stock turbos.
Josh
2fnloud
11-05-2011, 10:17 AM
Being able to read the numbers stamped on the housings would be more helpful, might get lucky I did and find out that your turbos are 13G's
AWDER
11-05-2011, 03:06 PM
I have read that the dr500s use a bored out 9b housing, so the numbers may be the same as stock. I was told that the dr500s do not have the taper and mine definitely don't have any sort of taper inside the inlet.
mb3000
11-05-2011, 03:16 PM
How much boost are you running?
AWDER
11-05-2011, 04:12 PM
Thinking I was on stock turbos, I have been running a max of 14 psi.
Chris@Rvengeperformance
11-05-2011, 05:20 PM
Measure the inlet.
Sent from my DROIDX using Tapatalk
mb3000
11-06-2011, 12:14 AM
Can you hold that to redline?
AWDER
11-06-2011, 01:27 AM
Well, at 6000 ft here in Parker, CO, 2nd gear holds solid to redline and 3rd holds it as far as I have gone. Have a 5 speed so I don't usually take the car that fast, as redline is 120+ mph. The turbos look brand new on the inside. Very clean and the nut holding the compressor wheel on still has a red marker stain on it. The car only has 62k miles on it though.
AWDER
11-06-2011, 01:31 AM
Here are a couple stock 9b pics I found. You can see the taper I am talking about in the inlet, so you can compare to my pics I took last night. Two of them are the rear turbo, but the inlet is the same style as the front.
Josh
DocWalt
11-06-2011, 03:51 AM
Measure the inlet.
Not quoting the useless text but this.
92RT-TT
11-06-2011, 04:47 PM
Measuring is what will tell you for sure... But I can tell you this, its not 13G's. G series wheels have a staggered blade configuration. More then likely an 11B but without measuring no way to tell for sure.
GTOJOE
11-06-2011, 08:03 PM
Measuring is what will tell you for sure... But I can tell you this, its not 13G's. G series wheels have a staggered blade configuration. More then likely an 11B but without measuring no way to tell for sure.
This /\ /\ definetly not a G series wheel of any kind. But I can see what you mean. The 9b has a wide opening that then tapers in towards the smaller 9b wheel while yours look like it's machined straight down. Usually when the 9b's are machined out to the stock numbers are filled off and new numbers stamped. Do they numbers all look like the factory cast numbers?
AWDER
11-06-2011, 08:18 PM
They have not been restamped, but I have seen a ton of pictures of DR500's now that were not stamped either. The 13C wheel in the DR500 has the same styling as a 9b as well. I knew they were not 13g's, but I am questioning whether they are DR500's. Basically a 13c wheel crammed into the 9b housing with some machine work and a clipped turbine. At least that is what I have read up to find a DR500 to be.
Looking at the inlets side by side on my computer mine just don't seem to look the same as the 9b's. Even the nut in the center is different.
Josh
GTOJOE
11-06-2011, 08:25 PM
What numbers are on the housings? the 11b turbo was an option in Japan for the MR models. Perhaps you have ended up with a set of those?
AWDER
11-06-2011, 08:56 PM
The front at least is 49177-02300. Which I know is the stock 9b housing.
Primus101
11-07-2011, 05:19 AM
This is what my DR500's look like-
http://i469.photobucket.com/albums/rr54/PRIMUS101A/103_1571.jpg
AWDER
11-07-2011, 12:23 PM
Yours looks more like a 13g. A DR500 looks like the 12 blade wheel in this picture, as it is a 13C compressor wheel.
http://www.dynamicracing.com/product_image.php?imageid=9
and like this
http://www.dynamicracing.com/product_image.php?imageid=8
Both are straight from Dynamic Racing's website.
Josh
As an aside to the topic, I have been collecting confirmations that DR500s are basically 13Cs.
True or not?
Primus101
11-07-2011, 02:19 PM
Hmmm. that's odd, I purchased them directly from DR last year-
Yes, 13c from what I understand-
Mitsubishi 13C Compressor Wheel - Turbochargers.com (http://www.turbochargers.com/store/product_info.php/cPath/38_49/products_id/366?osCsid=b4c3c9b4829565cb312892b60151f787)
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.