PDA

View Full Version : Megan Racing Catback



VR-4 0wnz j00
10-24-2011, 12:54 PM
I was wondering if anyone has bought/used this catback before. It says 2.5in outside diameter piping but I dont think 2.5in piping would mate to the cat/testpipe that is 3in. Can anybody confirm if its 2.5 or 3in at the cat?

Megan Racing (http://www.meganracing.com/product_detail.asp?prodid=1136&catid=14)

jessecain1
10-24-2011, 02:46 PM
hate to link to the other site but here you go. Ebay Exhaust Review G-Blue Knockoff <-- MUST READ --> - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f56/ebay-exhaust-review-g-blue-knockoff-must-read-508522/)

I personally run it on my car and it just plain souunds mean, has a nice deep growl to it not ricey at all (besides the looks, aka giant fart cans). It's three inches at the cat and then it has a y which goes to 2.5 inches to each side. oh and i know your going to ask, the ebay ones and the megan one are exactly the same they are both made out of California at the same location, they are just sold by different sellers

DrGonzo
10-24-2011, 03:33 PM
hate to link to the other site but here you go. Ebay Exhaust Review G-Blue Knockoff <-- MUST READ --> - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f56/ebay-exhaust-review-g-blue-knockoff-must-read-508522/)



Then link to the one I started here....LOL :http://www.3sgto.org/f13/ebay-exhaust-review-g-blue-knockoff-must-read-2188.html

For the price you can't beat it. Direct bolt on, 3" at the cat and splits back to 2.5, SS "of some grade" and sounds great!!

I have had mine installed now for almost a year and it still looks great and no rust at all!!! I think I am the first to get it for a 3S and have it installed.

2fnloud
10-24-2011, 04:15 PM
The seller has jacked his prices up, just checked. 395 Buy It Now.

DocWalt
10-25-2011, 02:56 AM
Then link to the one I started here....LOL :http://www.3sgto.org/f13/ebay-exhaust-review-g-blue-knockoff-must-read-2188.html

For the price you can't beat it. Direct bolt on, 3" at the cat and splits back to 2.5, SS "of some grade" and sounds great!!

I have had mine installed now for almost a year and it still looks great and no rust at all!!! I think I am the first to get it for a 3S and have it installed.

Pretty sure HLxDrummer has the same exhaust and he's had his for years now. I'll have to text him sometime.

VR-4 0wnz j00
10-25-2011, 04:56 AM
Just FYI,

Funny, he says 2.5 or 3in is good for a 2.0L NA engine but its also just fine for a 3L V6 TT, lol.

Greetings Jerel,

MEASUREMENTS:
- 2.5" OD piping, 4.0" tip, 2.5" ID @ inlet flange

It was for the entire system. Most exhaust systems are the same diameter throughout. Don't be too focused on diameter. Only 3" is needed for a boosted application, often times 2.5" +/- is more than enough for a N/A engine. On my own vehicle, a 1.6L, a 2.25" piping size creates a more usable powerband than a 2 3/8" piping size. On my 2.0L engine, it liked 2.5" but also has the capability to benefit from a 3" even when N/A, but only if you have supporting mods. Does your car have heavy engine work? (Internals)