View Full Version : VR-4 runs flawlessly except zero boost. Help me troubleshoot.
VR4Rob
10-22-2011, 02:27 PM
Car in signature. Running DR-650Rs (old style) with stock wastegates that have run fine for almost 3 years.
This problem sprang up out of nowhere, no symptoms, I just got in the car one day and it does not build boost at all. I can't hear the turbos spooling and the boost gauge on my HKS EVC reads 0.00 when accelerating. It accurately reads vacuum at idle. The car idles fine, drives fine, and pulls very smoothly through the revs all the way to redline but there's no boost at all. The car doesn't smoke and there's no oil in any of the intake pipes.
I did a quick check of all my vacuum lines and everything looks fine. On a hunch I swapped the front wastegate actuator to one I know for sure is good and still no change.
So what should I check next? I'm thinking this has something to do with my boost controller malfunctioning since the problem happened 'overnight.' How in the world it's running ZERO boost is beyond me though... Am I wrong in thinking that the car should run 5-6 PSI even if the EBC/solenoid is broken?
mb3000
10-22-2011, 02:37 PM
Might be some loose wiring on the gauge? With boost leaks and such I've run 0 boost, so not impossible to rule that out.
VR4Rob
10-22-2011, 03:45 PM
Might be some loose wiring on the gauge? With boost leaks and such I've run 0 boost, so not impossible to rule that out.
The 'gauge' is the electronic readout of live vacuum/boost on the HKS EVC. If there were boost leaks big enough for me to run no boost at all I'm almost positive I could at least hear them or the car would be nearly undriveable or wouldn't idle very well at all. As it is right now the car drives perfectly but the turbos just plain don't spool up to try to make any boost.
lawdogg
10-22-2011, 03:47 PM
Rob, try pulling the lines off the wg actuators ... if it builds boost, you know the problem isn't the wastegates or turbos. Watch out though, don't build too much. :p
green-lantern
10-22-2011, 04:09 PM
Pressure test yet? Does it feel like you lost power? You would think even with a bad boost controller you would run wastegate boost (6-7ish).
Roybatty
10-22-2011, 04:26 PM
Anything on the intake side can be suspect; as others say intake pressure test. Would also check BOV is functioning properly.
can you still FEEL boost? does that car feel otherwise normal? if so, you have a controller issue, not a leak.
VR4Rob
10-22-2011, 06:27 PM
Haven't pressure tested yet. Definitely can't feel any boost... The best way to describe it is that the car feels naturally aspirated. Thanks for the suggestion Ryan, that's a pretty good and easy thing to try that should tell me a lot.
BaadVR4
10-22-2011, 06:48 PM
Every time I've had this set of symptoms (three times in about 7 years with 4 different TT cars) the problem has been a seized turbo. Twice I heard the death "screech", once I didn't. A stuck open BOV or WG would present the same symptoms, as would one blown turbo. I'd pull the turbo intakes and check for turbo rotation. Just my experience.
NOMIEZVR4
10-22-2011, 07:06 PM
yeah...zero boost can't have many causes. the primary being sized turbos...keep us posted
VR4Rob
10-22-2011, 10:12 PM
Pulled the BOV (Blitz SS) and checked it. Seems to be working fine to me, definitely not stuck open. Pulled the vacuum lines from the wastegates and the car still doesn't boost. Guess the next step is to pull the intake pipes and make sure the turbos spin freely.
Hypothetically, wouldn't the car still build SOME boost even with one seized turbo? It seems extremely unlikely that one turbo would suddenly seize, much less both of them simultaneously.
Jimvr4
10-22-2011, 11:19 PM
Longshot but are the EBC connections soldered in, no T-taps?
lparrill
10-22-2011, 11:33 PM
If you don't have anything running wastegate with no vacuum, something serious is going on.
mb3000
10-23-2011, 12:05 AM
Skipped timing or cracked header's?
x2xtreme360
10-23-2011, 12:40 AM
Have you at least removed the intake pipes and spun the compressor wheel by hand?
OhioSpyderman
10-23-2011, 09:47 AM
If I recall correctly, IPO Chris had this exact problem at the first Michigan NG. One turbo WAS seized and he could not build boost.
Then again, that was QUITE a while ago, and I'm OLD :)
Maybe Chris will chime in....
Bob.
BaadVR4
10-23-2011, 09:54 AM
Usually one bad turbo allows about 8-10 psi from the other turbo. But the second turbo quickly goes south, even if you aren't boosting the car much. Since OP says the car seems to run "flawlessly" except for zero boost, I'm inclined to think one or both turbos aren't turning at all or they are turning but not building ANY pressure. A boost leak that big is almost always noticeable. I still think the next step is inspect or replace the turbos. If the turbo(s) are the problem, better to find out quickly and limit the run time. I dodged collateral engine damage all three times, but many have experienced total engine failure from bad turbo debris. It didn't take long, either. Just my 1.5 cents worth.
AdamVR4
10-23-2011, 11:18 AM
Only time I experienced these (exact) symptoms was when my rear 14B turbine fell the eff off on a highway on-ramp. The car ran great, didn't smoke, just wouldn't build any boost because one compressor wheel was driven by the exhaust gases and the other just freely spun, preventing any pressurization at all.
Of course, that wouldn't happen 'overnight'. Check the compressor side first, it's possible that something damaged the wheel. Pressure test the intake system before you remove the O2 housings ;)
*edit* Good advice from Baad - don't drive the car until you figure this out.
VR4Rob
10-23-2011, 11:24 AM
Awesome... lots of good suggestions guys. First thing I'll try is rotating the front turbo compressor wheel by hand as that will be the easiest to get to. Probably will do a pressure test after that and see where I am. :coo3l:
lawdogg
10-23-2011, 01:26 PM
Good luck Rob. I hope the damage isn't TOO bad!
Hans@GZP
10-23-2011, 02:59 PM
I third the motion of having a bad turbo. If one isn't creating boost, then the other turbo can basically pressurize the seized turbo IC piping and cause boost to come out of the intake. I've seen it a few times at the shop. Even a bent turbine shaft could do it as well.
green-lantern
10-23-2011, 03:01 PM
*edit* Good advice from Baad - don't drive the car until you figure this out.
I agree, don't tear up my favorite car Rob. :p
VR4Rob
10-23-2011, 07:44 PM
Well you guys were on to something... the front turbo is definitely seized. I just pulled off the intake tube and couldn't turn the compressor wheel by hand. Didn't have the time to check out the rear just yet but I have my suspicion that the bad news may continue there.
I'll at least get the front turbo off this week and see if I can tell what failed. Sucks that the (pretty much) newest mechanical part on the car failed but what can you do :rolleyes:
green-lantern
10-23-2011, 07:59 PM
Were these the billet turbo's?
JasonY
10-23-2011, 08:01 PM
They were the old school 650's that had been rebuilt, which is what leads me to my question. Who rebuilt them?
Jason
green-lantern
10-23-2011, 08:22 PM
They were the old school 650's that had been rebuilt, which is what leads me to my question. Who rebuilt them?
Jason
I thought so, time for some DR750 :)
VR4Rob
10-23-2011, 08:29 PM
They were the old school 650's that had been rebuilt, which is what leads me to my question. Who rebuilt them?
Jason
Correct they were the old style 650Rs. They were rebuilt by a very knowledgeable turbo shop about 2 hours from where I live. They have been building 3/S bolt on turbos for 10+ years. Nobody's perfect but I'll be pretty surprised if I find they failed due to a faulty rebuild.
OhioSpyderman
10-23-2011, 09:20 PM
Sorry Rob....twas just trying to help..
Hopefully you can get that BEAUTIFUL car back on the road with "not too much" out of pocket (we ALL know THIS will not be the case...)
Wish I could help (somehow), but I have two down myself right now (and 3 boys in college)....
Bob. :)
Broomfield Racing
10-24-2011, 11:25 AM
Noooo my favorite car :( How dare you break it!
This stinks Rob, hope she goes back together quickly.
AdamVR4
10-24-2011, 11:46 AM
Clogged oil feed line? Seems like a lot of you have seen turbos seize, what typically causes it?
BaadVR4
10-24-2011, 08:23 PM
I have had a piece of metal jam the exhaust wheel. Never did find out where it came from. Turbo had been fine for over 5K miles, so it is hard to imagine the metal fell in during install, but who knows? Other two failures were apparently faulty balance work which just wore the turbo(s) out in less than 50 miles (twice). I heard the "death squeal" when the metal jammed the exhaust wheel. It was horrible. I've put rods through blocks that didn't sound that awful.
VR4Rob
10-24-2011, 10:51 PM
Good news! The rear turbo spins just fine. I pulled the intake tube off of it tonight and it spins easily with a finger. I took the front heat shields off (yes, I reinstalled every single heatshield and bolt when I put in the DR650s, because blue car) and started soaking all of the bolts in PB. Hopefully sometime in the next couple of days I'll pull the front turbo out of the car and see what's up. I'm intrigued to say the least.
CoopKill
10-24-2011, 11:38 PM
Can you loan me your cars stance pleez? I love it!
VR4Rob
10-29-2011, 04:30 PM
Well how about this?
http://a3.sphotos.ak.fbcdn.net/hphotos-ak-snc7/300611_10100411638969071_7006518_51865057_18142821 45_n.jpg
http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/376975_10100411640525951_7006518_51865062_52951989 2_n.jpg
I don't see any physical damage to the exhaust wheel and the turbo spins just fine now that this stupid thing is out. Looks like I should be OK just putting the turbo back in the car :D Do I even need another one of these rings?
green-lantern
10-29-2011, 04:50 PM
That is crazy! Never seen that before
OhioSpyderman
10-29-2011, 05:04 PM
What the HELL is that?
Bob. :)
green-lantern
10-29-2011, 05:17 PM
What the HELL is that?
Bob. :)
It's a gasket ring that goes between the manifold and turbo.
VR4Rob
10-29-2011, 05:47 PM
So how many of you guys are running TD04 turbos without these rings?
JasonY
10-29-2011, 05:52 PM
A lot of people do. I have in the past with no ill effects.
Jason
VR4Rob
10-29-2011, 06:03 PM
A lot of people do. I have in the past with no ill effects.
Jason
Good. The rings were replaced with brand new ones when I installed the turbos 3 years ago. No way I'm putting them back on the car if I don't have to.
well if thing was keeping the turbo from turning at all, then you're lucky. shouldn't be any shaved parts or other trash going into your intake. exhaust restriction from hell, but other than that...no problem.
thor'svr4
10-29-2011, 07:10 PM
wow! i installed my turbos and got my car running then found those rings on my work bench. decided that it would be to much work to take the turbos off and put them back in so i just said screw it and left them out. now im glad i forgot to put them back in. i doubt youll have any issues without them in. ive been running for around 2 years without an exhaust leak or any ill effect so you should be fine.
i wonder why mitsubishi put them in there though...
green-lantern
10-30-2011, 01:21 AM
i wonder why mitsubishi put them in there though...
It was for a reason. I assume it helps to keep those manifold gaskets from leaking.
Jimvr4
10-30-2011, 01:38 AM
What material is the gasket? It shouldn't get brittle enough to split.
thor'svr4
10-30-2011, 02:16 AM
manifold to turbine housing gaskets are MLS.
BaadVR4
10-30-2011, 01:09 PM
Recognize that piece of metal. Mine was a more twisted and did damage the turbine wheel and exhaust housing. The ring is not part of the gasket, it is totally separate. The metal ring sits between the exhaust manifold and the exhaust housing and fits in a recess on both sides (iirc). I believe its purpose is to "center" the turbine exhaust housing/exhaust manifold and ensure the turbo/exh manifold are aligned correctly.
DocWalt
10-30-2011, 01:16 PM
It's called a "fire ring" and it's supposed to protect the gasket between the turbine housing and manifold. I don't think I've ever heard of one of the gaskets leaking unless the turbo wasn't secure.
green-lantern
10-30-2011, 02:03 PM
It's called a "fire ring" and it's supposed to protect the gasket between the turbine housing and manifold. I don't think I've ever heard of one of the gaskets leaking unless the turbo wasn't secure.
I've had them flip up when installing turbos before so it's a possibility it wasn't in there straight and the heat eventually caused it to break and make it's way into the housing.
Honestly I'd replace it Rob.
VR4Rob
10-31-2011, 12:27 PM
No way I'm putting a new fire ring back in the car if this brand new one failed after a pretty short amount of miles. They were installed correctly and I got extremely lucky it didnt take out the exhaust wheel of the turbo. The stock turbo housings are very well supported and the OEM gaskets are pretty stout... I think the fire rings were pretty unnecessary over-engineering by Mitsubishi (and I'm probably the last person on the planet that would ever say that)
AdamVR4
10-31-2011, 12:32 PM
If you're not going to reinstall it, port the exhaust manifold and turbine housing inlet to eliminate the step.
First time I've ever seen the fire ring fail. It really doesn't make any sense for it to fail if it were installed correctly. Either way, pretty cool, heh.
UTRacerX9
10-31-2011, 12:45 PM
It's called a "fire ring" and it's supposed to protect the gasket between the turbine housing and manifold. I don't think I've ever heard of one of the gaskets leaking unless the turbo wasn't secure.
This. I've run my car with 13T's for at least 5-6 years now without the fire ring, as my turbos and manifold are ported. So long as the studs/bolts are in good shape so you can properly tighten the turbo down, you won't hurt anything by leaving it out.
UTRacerX9
10-31-2011, 12:47 PM
First time I've ever seen the fire ring fail. It really doesn't make any sense for it to fail if it were installed correctly. Either way, pretty cool, heh.
Ditto. I can't see how it would fail unless it was "pinched" on install and got crushed accidentally.
AdamVR4
10-31-2011, 01:01 PM
Did a Sean Kelly do the install? :dontknow2: :Disdain: ;)
BigTyla
10-31-2011, 01:10 PM
Did a Sean Kelly do the install? :dontknow2: :Disdain: ;)
Dems fightin' words.
VR4Rob
10-31-2011, 03:53 PM
Did a Sean Kelly do the install? :dontknow2: :Disdain: ;)
http://www.mikey-san.net/static/bucket/ari-gtfo.gif
AdamVR4
10-31-2011, 04:08 PM
Man I love that gif. Well played ;)
Chris@Rvengeperformance
10-31-2011, 06:16 PM
If those get really hot they can distort and fall in the turbo. They have that split stock
I do not run them. Carefully line the turbo up and you'll be fine
Sent from my DROIDX using Tapatalk
AdamVR4
10-31-2011, 06:25 PM
If those get really hot they can distort and fall in the turbo. They have that split stock
You've seen this? How much boost was Rob running? What were his EGT's? Heat would cause the split ring to expand and close the 'split', but wouldn't there be more pressure on the inside face of the ring than the outside?
Chris@Rvengeperformance
10-31-2011, 07:20 PM
You've seen this? How much boost was Rob running? What were his EGT's? Heat would cause the split ring to expand and close the 'split', but wouldn't there be more pressure on the inside face of the ring than the outside?
matt monett has posted about it happening.
AdamVR4
10-31-2011, 07:28 PM
Ah, found a post on the subject here: Tha box is here! :) - Page 4 - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f1/tha-box-here-490904/index4.html)
on the ones in my car I simply took the "step" out that's there to hold the fire ring, did the same on my manifolds (the front one requires you weld on the flange on the out side if you do that, because it is welding on the inside). I choose not to use the fire ring because I have seen it on cars that are pushed hard and build allot of EGT melt, deform and make it's way down into the housing and come in contact with the turbine wheel.
I thought Rob always ran this car at waste gate boost? :p ;)
VR4Rob
11-01-2011, 03:37 PM
Ah, found a post on the subject here: Tha box is here! :) - Page 4 - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f1/tha-box-here-490904/index4.html)
I thought Rob always ran this car at waste gate boost? :p ;)
Haven't run a whole lot of boost though I did recently turn the wick up a little bit after I installed the 450cc injectors. I was running about 10 psi on the stock 360s (the car trapped 110mph on 10lbs) and had gotten a 'baseline' up to about 14-15 psi with the 450s before it stopped boosting. The extra boost and perhaps running a little leaner may have done the fire ring in. No sure way to know as I am only looking at NB 02s and knock counts for getting my basic pump gas street tune.
AdamVR4
11-01-2011, 03:39 PM
No EGT? What were your NB readings?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.