View Full Version : Running e85? Change what to use it? Long term reliability?
Gearheadvr4
10-21-2011, 09:41 PM
Just got e85 here so I'm considering the move with my build.
What do you have to change to make it work? Is it ok to run this long term?
I have a 3.5L fully forged block, AEM, 16g TD05, stock heads, hot wired single walbro 255, 720cc Densos, and mostly stock fuel setup other than a Aeromotive FPR.
Also on a side note, with the AEM could I have a tune for everyday driving on 93 pump and a race tune on e85? Or would I be better off just staying with one and leave it alone?
http://i429.photobucket.com/albums/qq12/gearheadvr4/518e6a90.jpg
FeaRpb
10-21-2011, 09:47 PM
Its going to be so sexy. I am so happy we finally got one down here.
Now I don't have to order it in bulk.
TurboSinceBirth
10-21-2011, 10:15 PM
Just got e85 here so I'm considering the move with my build.
What do you have to change to make it work? Is it ok to run this long term?
I have a 3.5L fully forged block, AEM, 16g TD05, stock heads, hot wired single walbro 255, 720cc Densos, and mostly stock fuel setup other than a Aeromotive FPR.
Also on a side note, with the AEM could I have a tune for everyday driving on 93 pump and a race tune on e85? Or would I be better off just staying with one and leave it alone?
http://i429.photobucket.com/albums/qq12/gearheadvr4/518e6a90.jpg
All you need to make it work is the parts to supply enough fuel for it and a way to tune it. You've got what you need except you'll need a 2nd fuel pump at the very least. Those 720cc injectors won't get you very far probably only to around 500AWHP before you're out of injector. I'd get some 1000 or 1250cc injectors if you want more power out of those turbos. The latter would be better for 600+AWHP. I'd recommend upgrading your stock feed line to -8AN fuel line also when you install a 2nd pump. Use the stock feed as the return.
Yes you could have a tune for the 93 map and one for E85. However, it's not as simple as you think. You would be better off having a completely separate tune for 93 and E-85 not just a map change like using the nitrous map for when you switch to the other fuel due to the different fuel demands. Ideally you'll want a separate fuel and timing map for each tune. I want to say with the use of a switch you can change between maps but I don't remember for sure.
There's also the factor of getting the same amount of ethanol in your tank every fill up. Having say 20% of the tank 93 and 80% of it ethanol is going to lower the ethanol content quite a bit and the ethanol map on the AEM will no longer be good. You'll want to run it empty before you fill up and also do an ethanol content test at the pump before you get E85. I don't think they have a winter blend where you live but if they do the ethanol map on the AEM won't work either because the ethanol content will be closer to 70%.
I'm sure you can tell that you want the same amount of ethanol in the tank every time you fill up for the AEM E85 map. That's why people like Chris Hill ordered in E98 by the drums so he never has to question what's in his car and the tune always stays rock solid. If you really want a good tuning solution check out Pro EFI. With the flex fuel sensor you can put whatever fuel in the tank you want. It can be all the way from a 10% ethanol content like you get with many places where you fill up with 93 pump, or E98. It has different timing and fuel maps for each tune and will basically interpolate depending on how much ethanol it reads in the tank. This will give you the correct timing and fuel plus it doesn't matter if the ethanol isn't the same every tank. I really like the Pro EFI but at a $3-4k investment before tuning it's hard to justify. At the cost of replacing a fully built 3.0L or 3.5L motor it's worth it, but verifying the ethanol in the tank before driving the car is a more viable solution for me when I'm on a budget and want to run E85. I won't have my tune running on the ragged edge either and the car will be going on a dyno to make sure it doesn't go past MBT and frag it.
arm0red1
10-21-2011, 10:48 PM
^^^^ this, outside of whats been previously stated some specific aftermarket fuel filters dont handle e85 all that well and can deteriorrate, but nothings been reported with the OEM stuff that im aware of
ALSO- e85 burns colder with the higher natural water product as a result of the combustion process and of being an organic fuel, so its much more susceptable to erratic ignition issues, such as things like spark blowout, but can be remedied with an HKS DLI/boost-a-spark, and closer plug gap to make sure the spark can still ignite the fuel.
Outside of that, here's a rough tunning/fueling estimate factor for e85 - whatever your hp goal is, take the amnt of fuel flow it would normally your car to achieve that hp, and then add roughly 30% increased flow to meet the same power demands on e85. Once thats done, feel free to run timing and maybe push the boost a little more as it is a cheaper race gas after all.
finally- expect fuel economy to reduce by abt 23-30%- so unless your area has stations dispersed a decent ways where you travel, or you have a large fuel cell in the back, as prev stated, set up two completely seperate maps for regular gas and e85
I've got a couple buddies running their cars on the stuff as we have 4 stations in town, a Procharged halltech C5 corvette, an AWD flashtunned talon running a gt35, a mkIV NA-T Supra running aem and a gt35R, an 04 STI running an HTA fp Red on a Cobb tune, and me giving it a good ole' fashioned try in my HX52 single vr4 with just a regular safc neo and maft until i can get something with timing (which is the REAL bonus for going e85) otherwise the most timing tricks i can pull off is just getting oversized injectors to trick the ecu into thinking the injectors are under light load and thus, advancing the timing.....ghetto, i know. But point being, no problems to date, the talon has been running as an e85 DD for 2 years, the vette for a year and a half, the supra and the STI for half a year, and I'm pending, the stuffs rather safe. and regardless of popular spread terror campaigns, wont eat your car alive under the hood.
FYI theres the new walbro in tank 400 from ninja performance, used the 255 motor with a new pump wheel for more flow, excellent e85 candidate pump, capable up to 800 bhp per pump for fuel, its intank, and bc its basically the wally 255 design, its stupid cheap, around 140-160 shipped for an intank pump thats as reliable as the old guy, and quieter from the new turbine wheel vs the old impeller/gear thingy they had going on.
- off note, what are the rims in the pick there, they b sexy, and im looking at them REEEAAAAALLLL hard for my 97...
Gearheadvr4
10-22-2011, 01:03 AM
1000cc wow! Im looking for 600 to 650hp fit a mostly daily driver but with enough ummhh to kill my buddies corvette. I'm not building a monster. You guys think I need that much fuel?
I couldn't just up the fuel pressure on the 720cc to get close to 800cc?
Btw the rims are Blitz Type 03 in blitz silver. Good luck finding them, I searched for nearly 3 years to find mine. Paid a hefty price to get them new from a Supra guy. I have 2 full sets thankfully so I have enough to last me. They were extremely rare when issued and had to be imported from Japan. Almost $800 plus shipping from Blitz for each one.
http://i429.photobucket.com/albums/qq12/gearheadvr4/c2665fec.jpg
arm0red1
10-22-2011, 03:49 AM
yup, thats abt the range u would roughly need, 850's minimum to achieve mid 500's with your IDC's in a nice place, sure, u can up the fuel pressure and see how far it takes you, but 1000's arent going to break the bank relatively on a 650 hp build, im looking for abt 650 awhp as well for the stock block on ine, readily doable, but you gotta set up for it in all respects. there are certain minimums in some areas that must be met, that there really isnt a way to skirt around the issue such as fuel flow. 3sx sells some pretty large injectors new for a good rate from an OEM/aftermarket supplier (delphi) for a good price or ninja performance has some 1250cc RC's for 560 shipped, your 720's will satisfy most of the bigger td04 crowd on pump/meth, and should sell pretty quick but in YOUR application its going to limit you for your e85 goals due to the nature of the fuel over conventional gasoline
gearhead, the standard is 30% larger injectors--iirc. 720's would be fine for ~600whp on a pump gas build. you do the math.
you need a MINIMUM of 2 pumps & upgraded line.
BigTyla
10-22-2011, 01:07 PM
Get a couple of extra OEM fuel filters if you end up going E85. Ethanol has some pretty good cleaning properties so when people make the switch their fuel filters end up getting clogged in the first few tanks. You'll want to keep a couple of filters handy in case this happens to you. Plenty of DSM guys are still running their stock OEM filter on E85 reliably.
TurboSinceBirth
10-22-2011, 05:25 PM
The Denso 720cc injectors flow 700cc. I have the data sheet for it from when mine were sonic cleaned and flow tested. I've seen multiple cars with PTE 780cc injectors run out of injector with ethanol around 500AWHP. You have to factor in DTL also so keep that in mind with your calculations.
J. Fast
10-23-2011, 03:59 AM
If you want to run a flex fuel setup you can just wire in an electronic enrichment / lean-out combination valve. Wire in a manual switch and tie it into one of your extension ports on the EMS and define it. It will run fine and the power will stay the same as pumpgas without modifying the timing.
The actual fuel increase is more like 18%, not 30%, for the same power output as pump gas.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.