View Full Version : While making some weight reductions in the VR-4, I was wondering...
OBXBoost
10-12-2011, 02:28 PM
Can I delete my oil filter?
My idea is that the faster the oil can circulate without the added restriction of the filter, the cooler it can be with the help of the oil cooler. Faster travel equals faster heat exchange, no?
Or should I just be better off keeping the filter and getting rid of the cooler?
HilbillyHomeboy
10-12-2011, 02:32 PM
Stop wasting your time and cut to the chase. Delete your oil pan. No more dents, less weight.
Jeremy
OBXBoost
10-12-2011, 02:33 PM
Stop wasting your time and cut to the chase. Delete your oil pan. No more dents, less weight.
Jeremy
Well I need *something* to hold in the oil! And by delete the oil filter, I also meant to get rid of the housing and replace it with a line instead. Just wanted to make sure I was clear.
UTRacerX9
10-12-2011, 02:37 PM
Are you serious? The filter is what keeps metal filings and other gunk from circulating through your engine. By removing the filter, you'd allow unfiltered oil to lubricate your turbos and cylinders, and my guess is that it wouldn't last very long at all.
EDIT: Technically, you can get rid of your oil cooler, but certainly not the filter. If you wanted to delete the cooler, than your best option would be to get a VERY large filter, that would allow you to increase your capacity by about 2-3 qts or so. Porsches used to not have oil coolers, but they also have twice as much oil as most cars in the crankcase to keep temp down.
OBXBoost
10-12-2011, 02:38 PM
Well I thought the oil cooler also played a part in that. Everyone replaces the oil cooler when they spin a bearing so I thought that also acts as a filtering agent...
UTRacerX9
10-12-2011, 02:43 PM
No. They replace the oil cooler because they are worried that metal filings would be trapped in it and don't want to run the risk of sticking it back on, even if they flush it out. Plus, if you've spun a bearing, it's time for upgrades, and an aftermarket oil cooler is fairly cheap.
For what it's worth, I was probably one of the first people who spun a bearing in these cars, back in 1995-96. Car was still under warranty, they replaced the rod, crank, etc, but did not replace the oil cooler.
KeithMac
10-12-2011, 02:46 PM
The oil cooler is where most of the debris is caught but by no means not ALL of it!. I think first port of call for the oil after filter and cooler is the crank oil gallerys..
OBXBoost
10-12-2011, 02:47 PM
So keep the filter and get rid of the cooler?
bridge
10-12-2011, 02:51 PM
Not a fan of this
BigTyla
10-12-2011, 02:53 PM
Getting rid of the cooler will only increase your line pressure by a small amount. To me it wouldn't be worth removing.
It's worth noting that the 1G DSMs cooled the oil by routing coolant to the oil filter housing. If you're really hellbent on reducing pressure loss in your lines, you might try making your own filter housing with coolant provisions.
AgentOblivious
10-12-2011, 03:06 PM
You can get rid of both...
...if you're into changing your oil every couple of days.
vroom4
10-12-2011, 03:08 PM
Is this a joke or are you high?
Turbo Beast
10-12-2011, 03:10 PM
I'll call TROLL on this one :)
Deleting the oilfilter HAH!
OBXBoost
10-12-2011, 03:46 PM
Is this a joke or are you high?
I'm not known for doing drugs, nor am I known for a sense of humor.
So is there anyway to make this work besides lots of oil changes? And I think every few days is a little bit exagerrated, no?
DocWalt
10-12-2011, 04:36 PM
Wait, this is serious? I was all ready to get out my troll and everything... http://freeemoticonsandsmileys.com/animated%20emoticons/Halloween%20Animated%20Emoticons/dance%20troll.gif
mb7050
10-12-2011, 04:44 PM
I'm not known for doing drugs, nor am I known for a sense of humor.
How about mental illness?
92RT-TT
10-12-2011, 04:44 PM
If you are worried about your oil pressure being to low, you've got other issues like a bad pump, worn engine etc... they put the oil cooler and oil filter on the engine for a reason, not just to look pretty...
BaadVR4
10-12-2011, 04:58 PM
Not to mention they aren't that pretty, either. Point is: OEM equipment costs are micromanaged to the .1 cent per unit cost. If something costing as little as a tenth of a penny can be deleted without serious consequences, it would be eliminated. The mere fact that Mitsubishi spent the money for an oil cooler tells us their engineers had good reason to do so. And, as far as I know, any internal engine run without an oil filter is just a boat anchor waiting for conversion.
Unless you want the headaches of oil system failure, I'd suggest you keep both the filter and the cooler. If you want to reduce pumping loss, you could install dual remote oil filters (in parallel) and dual oil coolers (also in parallel). Just my 1.5 cents worth.
Alan92RTTT
10-12-2011, 05:07 PM
Suckers.
ictponder
10-12-2011, 05:24 PM
Has anyone ever considered making an oil filter catch with a series of neodymium blocks to catch any sediment?
mb7050
10-12-2011, 05:25 PM
a dual oil filter setup like Perma Cool dual filter(in parrallel)will reduce the restriction which should keep the oil flowing a bit better.Oil tempertures may be lowered a bit and the quantity of oil in the system would be increased by a quart. but then again Why add the complexity and extra parts that can fail,...
familyMAN
10-12-2011, 05:31 PM
I would delete the engine. Less weight, and no chance of failure.
mb7050
10-12-2011, 05:37 PM
I would delete the whole car and buy a tricycle
did obxboost start this thread, or oxyrageous?
Chris@Rvengeperformance
10-12-2011, 06:51 PM
ok the real solution to this is to do like a guy I used to know did. He had a huge hole in his oil pan. rather than getting a new pan or even bubble guming a patch he kept a 55 gallon drum of waste oil in the bed of the truck. Then he ran a hose to the oil fill. When he wanted to drive he turned on a small electric pump.
So, what you can do is remove your oil drain plug and then put a drum of oil in the hatch with a hose and pump. If you are a baller you can buy new oil and have the cleanest oil at all times!
oh and I know what you are going to say...55 gallons of oil is heavy, but you forgot about the helium infused oil!
EvanH
10-12-2011, 08:16 PM
You're going to break a ring-land
CoopKill
10-12-2011, 09:20 PM
:suspect:
mb3000
10-13-2011, 12:14 AM
This guy looped the oil feed into the front preturbo intake tube (3/8") Keeping that front turbo nice and lubricated.
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/golferman.jpg
J. Fast
10-13-2011, 12:25 AM
If it were me, I just wouldn't put any oil in it. That way I wouldn't have to worry about keeping anything cool or filtering possible contaminants.
OBXBoost
10-13-2011, 11:03 AM
If it were me, I just wouldn't put any oil in it. That way I wouldn't have to worry about keeping anything cool or filtering possible contaminants.
Didn't 3SX do that with the Panda?
sublime_whatigo
10-13-2011, 05:11 PM
That was after they "replaced" it with coolant
VR-4ever
10-14-2011, 01:59 PM
Faster travel equals faster heat exchange, no?
Faster travel can reach a point where the fluid is not in the heat exchanger for the amount of time needed to shed the energy each time around, and can lead to thermal runaway.
http://www.wiichat.com/forum/attachments/anime-lounge/8648d1311055173-hanamaru-kindergarten-plz-stop-post.jpg
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.