PDA

View Full Version : struggling to get an axle out.



shmoo
10-09-2011, 02:07 AM
how's it going guys?

i've been struggling to get axle out of this stealth. we got half of the other side out, which is good enough for me. so there are sill axle splines in the driver's side, but hopefully good enough to get the motor out.

i've never had so much trouble doing simple things..

my friend scott managed to us a nice pry bar to get the transfer case off where i had been struggling. so i think i need a set. he paid 50 for three nice ones. i may go to harbor freight and pay seven for three or four far weaker looking ones.

but yes, any hints to getting a stuck axle out. it's been showered in wd40, and a little pb blaster. tugged, and used other type pry bars. i bought a beefy bar from harbor freight for ten, i just don't think it quite fit.:rolleyes:

so help, i want this motor out. i'm struggling enough on things i have already done, while i've hardly reached the steps that i haven't done.

_isiah

Alex3000gt
10-09-2011, 02:20 AM
Driver's side axle is stuck? Front? Did you unbolt the intermediate shaft from the block?

Or are you stuck on the passenger's side axle? On the front passenger's side you should be able to use a crowbar between the trans housing and the thick part of the axle and pry it out. If you remove the battery you will have a pretty good vantage point from above on where you need to pry.

lawdogg
10-09-2011, 02:25 AM
Pry bar! Or, put the tip of a long bar on it and whack the other side with a hammer! Shock impact sometimes works best to pop it out of the little snap ring groove.

MR2
10-09-2011, 04:15 AM
I find rattling it around and rotating it around 180 degrees and so forth (to get the snap ring roughly centered) gets it out every time.

what the hell is with this car to need a bloody pry bar to get the transfer case off!! :p

lawdogg
10-09-2011, 04:31 AM
I find rattling it around and rotating it around 180 degrees and so forth (to get the snap ring roughly centered) gets it out every time.

what the hell is with this car to need a bloody pry bar to get the transfer case off!! :p

It was funny, when I was swapping out my 5spd drivetrain for the 6spd, the 5spd t/c basically jumped into my hands when I took it off! I was lying under the car frozen with shock!!

MR2
10-09-2011, 04:50 AM
It was funny, when I was swapping out my 5spd drivetrain for the 6spd, the 5spd t/c basically jumped into my hands when I took it off! I was lying under the car frozen with shock!!

Damn! did that hurt?

lawdogg
10-09-2011, 04:58 AM
Haha no, 5spd tc is pretty tiny. :p

TwIzTeD_3kGt
10-09-2011, 09:09 AM
Large flat chisel and a mini-sledge, don't be afraid to hit it.

Never pull on the axle, you'll just pull it apart.

green-lantern
10-09-2011, 02:27 PM
Pry bar! Or, put the tip of a long bar on it and whack the other side with a hammer! Shock impact sometimes works best to pop it out of the little snap ring groove.

This

If prying with a pry bar be very careful not to put a hole the trans.

1993RT/TT
10-09-2011, 06:15 PM
Large flat chisel and a mini-sledge, don't be afraid to hit it.

This is what worked for me on the passenger side. I used it to wedge in between the axle and the trans housing and it popped off on the first or second hit.

MR2
10-09-2011, 06:19 PM
ok, lets get this a little more organised, standing in front of the car, the left hand axle has the snap ring. the right hand side does not(on any I've seen), only thing holding the right side in is the half shaft which is only 2 bolts and the easiest way to get this out (I've actually never managed to separate my half shaft :p)

TwIzTeD_3kGt
10-09-2011, 07:16 PM
ok, lets get this a little more organised, standing in front of the car, the left hand axle has the snap ring. the right hand side does not(on any I've seen), only thing holding the right side in is the half shaft which is only 2 bolts and the easiest way to get this out (I've actually never managed to separate my half shaft :p)

I usualy separate it and leave the intermediate shaft bolted to the block. Less bolts taken off = faster engine pull, and less to remember where to put back.

familyMAN
10-09-2011, 08:02 PM
chisel

shmoo
10-10-2011, 02:37 AM
Driver's side axle is stuck? Front? Did you unbolt the intermediate shaft from the block?

Or are you stuck on the passenger's side axle? On the front passenger's side you should be able to use a crowbar between the trans housing and the thick part of the axle and pry it out. If you remove the battery you will have a pretty good vantage point from above on where you need to pry.

it's the passenger's side. battery is out. still struggling.
thanks.


Pry bar! Or, put the tip of a long bar on it and whack the other side with a hammer! Shock impact sometimes works best to pop it out of the little snap ring groove.

put the tip of this long bar in between the axle and the transmission? and hit the top of the long bar?


I find rattling it around and rotating it around 180 degrees and so forth (to get the snap ring roughly centered) gets it out every time.

what the hell is with this car to need a bloody pry bar to get the transfer case off!! :p

i'll probably try this first. seems gentle. i don't know that i've tugged in the correct sequence.

well the previous owner had her overheat pretty badly, but i doubt that's related to the transfer case. i tugged and tugged, and ended up having it loose. but all the pulling and wd40 wouldn't free the bond. i've been wondering if the transfer case has ever been off of the transmission. we have another mitsubishi dealer now, i should see about getting that taken care of.


Large flat chisel and a mini-sledge, don't be afraid to hit it.

Never pull on the axle, you'll just pull it apart.

the axle is a tad free already. not more than a millimeter or two. you're saying to put something about the size of the space provided in between the transmission and axle.. and hitting the top of the chisel?

yeah, i've seen the boot flex a little. i've got a couple random extra axles and a lifetime warranty for the driver's side i believe. i hope i don't have trouble getting a plethera of new axi.

like i said before.. i wonder what on this car has been replaced.


This

If prying with a pry bar be very careful not to put a hole the trans.

thank you! i stopped prying yesterday because of that thought.


This is what worked for me on the passenger side. I used it to wedge in between the axle and the trans housing and it popped off on the first or second hit.

so something that fits right in between the two? and a good firm hit on top to jar it free?

thanks a butt load guys! i need to get this done my life is getting sticky again.

_isiah

shmoo
10-10-2011, 02:42 AM
I usualy separate it and leave the intermediate shaft bolted to the block. Less bolts taken off = faster engine pull, and less to remember where to put back.

huhh?

and pull the transmission and motor at the same time still. what would happen on the passenger's side?

wait wait.. may i have your phone number?

_isiah

shmoo
10-10-2011, 02:50 AM
ok, lets get this a little more organised, standing in front of the car, the left hand axle has the snap ring. the right hand side does not(on any I've seen), only thing holding the right side in is the half shaft which is only 2 bolts and the easiest way to get this out (I've actually never managed to separate my half shaft :p)

gooood info. it is the left (passenger's side) axle that i can't get out.

my driver's side is in two halfs. but i think it looks like it may go back together.

can't wait to try this out.

thanks everyone, goodnight!

_isiah

MR2
10-10-2011, 03:48 AM
if the TC is hard to get off the shaft I would consider this a danger sign and inspect the shaft for damage, could have just somehow stayed dry??

while rotating the shaft around don't be afraid to get a pry bar in there and gently tug/encourage it out.

Roybatty
10-10-2011, 02:26 PM
I didn't c this mentioned in a quick scan, buy make sure she is in neutral or X-case won't budge.

connected via tapatalk

TwIzTeD_3kGt
10-10-2011, 03:22 PM
I didn't c this mentioned in a quick scan, buy make sure she is in neutral or X-case won't budge.

connected via tapatalk

He's trying to remove the passenger half-shaft.


huhh?

and pull the transmission and motor at the same time still. what would happen on the passenger's side?

wait wait.. may i have your phone number?

_isiah

Passenger side axle has to come out. There should be a 'flat' section of the axle head right next to the trans. I usually get the chisel on there and hit outward (toward the wheel).

speedy25
10-10-2011, 11:15 PM
SOMETIMES the axle wobbles around a bit too much and creates a burr where the snap ring is. Thats what makes it a pain to get out sometimes. As you know usually a good twist with a pry bar is enough. My trick is two large chisels inserted 180 deg. apart and a whack on the axle hub. Sometimes it takes a few tries. I did have a Honda axle that REFUSED to come out of an intermediate shaft, but that was dealt with another way.

Keep at it. It will come out.

-SP

Alex3000gt
10-11-2011, 12:00 AM
Man up and pry that axle out of there.
:)
Pry, rotate, pry. If you cannot get a good angle with your pry bar, buy a better one.

shmoo
10-11-2011, 05:09 AM
just came back inside. got the bloody axle out!

-chisel up top and rubber malleted in
-little pry bar wedged in the bottom. normal hammered in
-POP!
-leak
-drain transmission fluid. i seriously thought i busted something. but i think all is good now..
-then used my healthy jimmy bar to move the axle. a very satisfactory sight.

do i need to make another thread?:
i'm hoping to attempt to pull this motor in the next couple of days.

i just put the calipers and wheels back on, and set her down.
am i fucking up yet? what am i missing?

this'll be my first pull, but i think things are looking alright so far.

thank you!!

_isiah

TwIzTeD_3kGt
10-11-2011, 12:50 PM
Were you doing brakes too? No need to remove the calipers if you're just pulling the engine. Either remove the strut-knuckle bolts or the lower control arm bolts in order to get the axle out.

As for pulling the engine, I just remove everything that connects engine to the body, and anything that blocks the engine/trans from going up. You can pretty much leave everything on except axles, down-pipe, P/S and A/C pumps, intake piping, oil cooler lines, and the wiring harness. Some people say you need to remove the alternator and upper intake manifold, I never do and they clear just fine. After all that, just unbolt the front and rear motor mount center bolts, remove the side mounts completely and pull it up.

What do you have left to do?

Alex3000gt
10-11-2011, 07:23 PM
You should have drained the trans oil from the diff before you pulled the axle for less mess. Oh well, you drained it one way or another, haha.

Good work, glad my motivation helped.

shmoo
10-13-2011, 03:20 AM
got the Motor Out! feels great..

thanks for all the help. i need to get the car away from her current location, but i'm wanting to pull the remaining shit off the firewall, along with the front bumper, and paint. but i'd like to make some headway on how the car runs first.

for now, i need to get the transmission off
get the motor on a stand
and relocate the car. so i can get shots for my dog and get the hell out of dodge.

i may be headed west shortly with my dog and ani. i'd like a couple places to stop and relax. anyone have me? the destination is washington state. we'll say around seattle.

thanks!

_isiah

Boomer3000
10-13-2011, 04:32 AM
Why the move man? Pm me if ya don't wanna say on here.