PDA

View Full Version : Deleted my oil cooler.



Intropy
10-03-2011, 10:58 PM
And I'm feeling pretty smug about it.

Problem? I guess I'll find out.

Badandy247
10-03-2011, 11:16 PM
Any specific reason? I would assume that you monitor oil temps correct? I really like your car, don't let her get hurt.

mb3000
10-03-2011, 11:20 PM
:suspect:

J. Fast
10-03-2011, 11:50 PM
Saaawha, you crazy fool! You must trust your tuner skillz :)

KPZVR4
10-03-2011, 11:52 PM
Why would you want to make sure that your oil is hotter than normal?

VR-4 0wnz j00
10-03-2011, 11:57 PM
Hmm, guess you dont care about longevity of your engine.

J. Fast
10-04-2011, 12:10 AM
It's has nothing to do with longevity. The pickup is still a straw, the oil cooler holds... an extra quart? You think that helps the bearings? You can buy oil for your operating temp range just like you can buy brake pads for your temp range. Besides, He's controlling the load on the engine with the tune and can cap the ceiling. Must have a ton of data being collected on the engine to feel comfortable enough to do that.

What's your oil temp range at full load and at idle Intropy?

Austin@STM
10-04-2011, 12:31 AM
As long as everything is in good order, you wont have an issue. We do this on plenty of cars.

That being said, if you plan on auto crossing or road racing it would be a good thing to have im sure after all the continued high RPMs.

AdamVR4
10-04-2011, 11:06 AM
And I'm feeling pretty smug about it.

Problem? I guess I'll find out.


How did you justify your decision? What oil cooler were you running? What were your temps? What are they now? What oil were you using? What oil are you using now?

I essentially deleted mine in 2004 by gutting the oil cooler bypass valve. After examining the oil flow diagram I replaced the valve. My engine bearings looked fine after limited mileage. It's not something I'd feel comfortable with on a daily driver in 100+ deg F weather or during continuous abuse. But that's based simply on my engine's oil pressure (20W-50 or 5W-50) and water temperature.

Where is this high temperature oil J. Fast?

Intropy
10-04-2011, 02:23 PM
How did you justify your decision?

"My oil cooler lines are leaking. ... There, I fixed it." :D

Ha ha, sorry, I may have gotten everyone worked up over nothing. This is my stockish DD, not the TD05 car. That car has a ginormous front-mounted setrab cooler.

I was having a hard time believing that my rusty old stock cooler, with no ducting (had to remove for the FMIC), and tilted at a 20-degree angle was doing much of anything anyway. I'm running 20w50 now that I deleted it.

TwIzTeD_3kGt
10-04-2011, 06:28 PM
"My oil cooler lines are leaking. ... There, I fixed it." :D

Ha ha, sorry, I may have gotten everyone worked up over nothing. This is my stockish DD, not the TD05 car. That car has a ginormous front-mounted setrab cooler.

I was having a hard time believing that my rusty old stock cooler, with no ducting (had to remove for the FMIC), and tilted at a 20-degree angle was doing much of anything anyway. I'm running 20w50 now that I deleted it.

Ahh so you're just guessing everything will be fine, that makes me feel better. :scared:

Not going to at least try to monitor temps, if not for safety, for science? I'm just curious what the actual temperature difference is without a cooler.

Alex3000gt
10-04-2011, 09:13 PM
As a powertrain cooling expert:

Don't feel so smug.

Intropy
10-05-2011, 12:03 AM
Hmm, nope, still feeling pretty damn smug.

Got an oil cooler on that NA of yours? If I'm going to be dislodged from my happy place, someone has to convince me that my massive 5-second, 240whp-merge-into-freeway-traffic poses some dramatic thermal threat to my engine.

i3igpete
10-05-2011, 12:24 AM
just monitor your oil temps. for example, the maximum oil temp spec for a lamborghini V12 is 135 degrees celsius.

Maximal
10-05-2011, 10:07 AM
Yeah, for a DD without any extended high RPM runs I don't see it being an issue. If you ran a few laps on a roadcourse you'd probably be buying a new engine though. :p

AdamVR4
10-05-2011, 01:50 PM
As a powertrain cooling expert:

Don't feel so smug.


Are you typing 1-handed or something? Why can't you make posts that are over 100 characters?

Laughfer
10-05-2011, 04:56 PM
Are you typing 1-handed or something? Why can't you make posts that are over 100 characters?

I laughed

green-lantern
10-05-2011, 04:58 PM
:lo5l:


Are you in town Justin or do you have the beater in CA now?

Intropy
10-05-2011, 07:50 PM
:lo5l:


Are you in town Justin or do you have the beater in CA now?

Yeah, both cars are with me in LA. The TD05 car is so freaking nice I don't even care about this one anymore. I tried to sell it for $3k (figuring I'd get a lowball $2500) and couldn't even get rid of it. :lo5l:

green-lantern
10-05-2011, 08:10 PM
Yeah, both cars are with me in LA. The TD05 car is so freaking nice I don't even care about this one anymore. I tried to sell it for $3k (figuring I'd get a lowball $2500) and couldn't even get rid of it. :lo5l:

Might as well keep it for beating on. Hell I'd probably take it for 2.5. It's cool you got the TD05 car running good, congrats!

J_Parker
10-05-2011, 10:03 PM
Although not the same car, engine type or displacement, I deleted the oil cooler on my Soarer when I still had it. At the most, all I had was about 10* difference under hard driving conditions. Hardly enough to even pay attention to it anymore. I hope it works out for you in the meantime man.

Intropy
10-05-2011, 10:07 PM
Yeah I don't expect any problems considering I really only commute in it. Honestly I will probably replace it with a front-mounted aftermarket one, I just needed to fix the leak and thought I'd stir up some shit in the meantime.

green-lantern
10-05-2011, 10:33 PM
Yeah I don't expect any problems considering I really only commute in it. Honestly I will probably replace it with a front-mounted aftermarket one, I just needed to fix the leak and thought I'd stir up some shit in the meantime.

Fuck no! your shit is toast nOOb!

Did I mention I'm a nuclear expert?

Boomer3000
10-06-2011, 03:33 AM
:suspect: .... I haz Flux Capacitor....




Potato???

Ninja Performance
10-06-2011, 01:02 PM
Hmm, nope, still feeling pretty damn smug.

Got an oil cooler on that NA of yours? If I'm going to be dislodged from my happy place, someone has to convince me that my massive 5-second, 240whp-merge-into-freeway-traffic poses some dramatic thermal threat to my engine.

Got turbos heating that oil on yours?

-Chris

Intropy
10-06-2011, 01:32 PM
Got turbos heating that oil on yours?

-Chris

Does a turbo at cruise heat oil? If a tree falls in the woods, does it need an oil cooler? :lo5l:

Nah I'm just messing with you. I wouldn't think it would be a problem unless I get on it.

Boomer3000
10-06-2011, 01:43 PM
I thought it was if a bear poops in the woods does it need an oil cooler??

vroom4
10-06-2011, 04:54 PM
Did I mention I'm a nuclear expert?

Worst argument ever. They give that title to literally ANYONE these days.

Keyan
10-06-2011, 07:43 PM
i dont see it being a problem if you're not beating on it; in the same way you could delete your FMIC. "i never beat on it, so whats the problem?"

well, the FD rx7 comes equipped with 2 oil coolers, one under each headlight. and a single turbo intercooler that is about the size of one of our OEM sidemounts. its all about knock control. the heat of the motor has a lot to do with it. you could tune out the heat with some timing adjustments; but since its just a temporary fix and not something planned for high performance use ("i deleted my oil cooler because it wasnt doing anything anyway!" <- bad idea) i dont see it being a problem.

Alex3000gt
10-06-2011, 10:44 PM
Are you typing 1-handed or something? Why can't you make posts that are over 100 characters?

Interesting observation.

Alex3000gt
10-06-2011, 10:49 PM
The company I work for designed the cooling system in these cars.

Blue91SL
10-07-2011, 01:07 AM
The company I work for designed the cooling system in these cars.

The company I work for designed a cake once.

anyonebutme
10-07-2011, 01:55 AM
The company I work for designed all the ways to break these cars.....

Boomer3000
10-07-2011, 01:58 AM
Sames^^^

AdamVR4
10-07-2011, 05:06 PM
The company I work for designed the cooling system in these cars.

So why don't you ask somebody there to post something useful?

Alex3000gt
10-07-2011, 06:43 PM
So why don't you ask somebody there to post something useful?

Still reeling from the political threads I see?

Go calm down.

anyonebutme
10-07-2011, 08:00 PM
Still reeling from the political threads I see?

Go calm down.

He sounds calm to me. He did just give you a great opening, that you took great pains to avoid. Multiple times.

If it were me, and I was a thermal engineer, I'd have taken to chance to pull some records out or made some assumptions based on similar designs and make a useful post such as:

"Well, the 6G72TT was estimated/tested to produce 460,000 BTU/hr at full load into the cooling system and 238,000BTU/hr into the oil cooling system based on it's available fuel rate and BSFC under full load. The stock cooling system in good condition was designed to expel that with a safety factor of 1.8 to account for eventual cooling system deterioration. Removing the oil cooling system will make the water cooling system pass it's safety factor trying to expel the additional heat under full load or additional load from modifications, which will cause oil to overheat and eventually the whole engine to overheat. OEM applications usually call for a oil cooler of xBTU/hr per 100HP produced at the flywheel, even for 'daily driving' conditions."

The ability to use your current knowledge or ability to gain that knowledge through research, process it, and then release that knowledge for the benefit of others through clear communication is the hallmark of an excellent engineer. Those type of people, whether or not engineers or just people who push their own cars to their own limits, are usually the people who a community such as ours look up to for advice or to admire their accomplishments. Adam as achieved such a position through his accomplishments and such sharing of knowledge.

Strange, you can find nearly all those people in one place...Yes I pulled those numbers out of my ass.

green-lantern
10-07-2011, 08:08 PM
Worst argument ever. They give that title to literally ANYONE these days.

Not as much as engineers but yeah nuclear still sounds cool :suspect:

markoverclock
10-07-2011, 08:36 PM
The company I work for designed the cooling system in these cars.

so your the one to blame for shitty coolant temp issues. lol. why do the 90-92 have the temp switch to activate the fans on the bottom of the radiator??? What was the thinking on that?

Ninja Performance
10-07-2011, 08:56 PM
Does a turbo at cruise heat oil? If a tree falls in the woods, does it need an oil cooler? :lo5l:

Nah I'm just messing with you. I wouldn't think it would be a problem unless I get on it.

Tell ya what ;)
Idle your car for 20 minutes. Then go and grab the turbine housing with your bare hand, hold for 30 seconds. Let me know if it is hot. The oil is moving thru it while idling that hot. The turbos are introducing heat into the oil. ;)

I'll stick with my oil cooler. It surely can only help and surely can't hurt.

-Chris

green-lantern
10-07-2011, 09:23 PM
I'll stick with my oil cooler. It surely can only help and surely can't hurt.

-Chris

Unless it's leaking all the oil out.

I'm not sure if people are reading this whole thread lol

Ninja Performance
10-08-2011, 09:42 AM
Unless it's leaking all the oil out.

I'm not sure if people are reading this whole thread lol

Oh, I am reading...but to me, deleting an item like an oil cooler because it is leaking is not the correct course of action. While things like the clutch booster tank can be removed without ill effects, things like the oil cooler are there for a very good purpose and IMO shouldn't be deleted if leaking, they should be fixed. Unless it's a temp thing to limp around out of boost until you can afford the time or money to fix it correctly.

-Chris

Gamerse
10-08-2011, 01:01 PM
As long as everything is in good order, you wont have an issue. We do this on plenty of cars.

That being said, if you plan on auto crossing or road racing it would be a good thing to have im sure after all the continued high RPMs.

Do you have any temp data? Share please. :)

K cars never had oil coolers, turbo or not. Then again, they used coolant/oil cooled T3 garretts from the factory. On the other hand, some switched to oil cooled turbos. (the flavor they picked was not available with coolant cooling) Those cars are still on the road today. So for a longevity test, the only ill effects I could foresee would be higher cartridge temps, and what happens there is another discussion.

I'm sure I missed something in the other two pages, I didn't have time to buz through them.

mb7050
10-08-2011, 04:45 PM
Unless it's leaking all the oil out.



Then its time to replace it, Its there for a reason.. sure you can survive without but I would never completely delete it for good.

AudibleSilence
10-08-2011, 05:13 PM
Oh, I am reading...but to me, deleting an item like an oil cooler because it is leaking is not the correct course of action. While things like the clutch booster tank can be removed without ill effects, things like the oil cooler are there for a very good purpose and IMO shouldn't be deleted if leaking, they should be fixed. Unless it's a temp thing to limp around out of boost until you can afford the time or money to fix it correctly.

-Chris

THIS. I'm in for the explosion. :)

green-lantern
10-08-2011, 06:47 PM
You guys are being trolled so bad :lo5l:

mb7050
10-08-2011, 07:18 PM
I just had to express an opinion being trolled or not ha ..

green-lantern
10-08-2011, 07:24 PM
I just had to express an opinion being trolled or not ha ..

lol understood, no way in hell I'd run without one, at least my car and the way I drive.

mb7050
10-08-2011, 07:33 PM
oh you can make yourself complete oil cooler Assembly for very cheap

green-lantern
10-08-2011, 07:37 PM
oh you can make yourself complete oil cooler Assembly for very cheap

Please elaborate, I'm thinking of upgrading mine soon.

Ninja Performance
10-08-2011, 07:41 PM
Please elaborate, I'm thinking of upgrading mine soon.

Cheap being cheaper than a stock OEM new replacement. That shits expensive!

-Chris

mb7050
10-08-2011, 07:44 PM
1 cheap ass ebay core will do the job like this http://cgi.ebay.com/ebaymotors/UNIVERSAL-30-ROW-ENGINE-TRANSMISSION-RACING-OIL-COOLER-/110754901409?pt=Motors_Car_Truck_Parts_Accessories&hash=item19c981ada1#ht_2770wt_1165
2 Adapters For Oil Cooler if necessary -10 AN Female To -8 AN Male in this case
2 -8AN 45-90-degree Hose Ends fittings near the oil filter
2 -8AN 0-90 degree Hose Ends fittings at the cooler.
of -8AN Hose 7 feet or less if sidemount
2 -8AN to M16x1.5 Metric Adapters into the holes in the oil filter housing
2 M16 Crush Washers (Copper or Aluminum)


or just buy the hose assembled ie
http://cgi.ebay.com/ebaymotors/NEW-8-Hose-Assembled-Strt-90-Ends-3-Length-/220677611046?pt=Motors_Car_Truck_Parts_Accessories&hash=item3361691e26#ht_3453wt_939

ebay for cheap parts
http://cgi.ebay.com/ebaymotors/10-Female-8-Male-Flare-Reducer-PRE-60820BLK-/260704691365?pt=Race_Car_Parts&hash=item3cb335e4a5#ht_1193wt_939
http://cgi.ebay.com/ebaymotors/Black-8-90-Degree-Swivel-Hose-End-Fitting-Braid-/310348489693?pt=Motors_Car_Truck_Parts_Accessories&hash=item48423623dd#ht_500wt_956
http://cgi.ebay.com/ebaymotors/Black-8-90-Degree-Swivel-Hose-End-Fitting-Braid-/310348489693?pt=Motors_Car_Truck_Parts_Accessories&hash=item48423623dd#ht_500wt_956
http://cgi.ebay.com/ebaymotors/8-Braided-Stainless-Steel-Fuel-Line-Hose-1500-PSI-/230661899601?pt=Race_Car_Parts&hash=item35b4854551#ht_1384wt_939
http://cgi.ebay.com/ebaymotors/?cmd=ViewItem&_trksid=p3984.m1439.l2649&item=310329201024&sspagename=STRK%3AMEWNX%3AIT#ht_2141wt_939
http://cgi.ebay.com/ebaymotors/CW901-M16-16mm-Aluminuim-Alloy-Crush-Washers-10-Pk-/110694502610?pt=Race_Car_Parts&hash=item19c5e810d2#ht_2573wt_939

mb7050
10-08-2011, 07:47 PM
you can buy good quality stuff from ebay too like this and its relatively cheap way cheaper than OEM
NEW Fluidyne AN8 Engine Oil Cooler 11x8x2 | eBay (http://cgi.ebay.com/ebaymotors/NEW-Fluidyne-AN8-Engine-Oil-Cooler-11x8x2-/360351537196?pt=Motors_Car_Truck_Parts_Accessories&hash=item53e6a0182c#ht_500wt_956)

Ninja Performance
10-08-2011, 07:48 PM
Good posts!

-Chris

mb7050
10-08-2011, 08:25 PM
thanks
you can make yourself an equivalent kit to this using the ebay core for less than 180$ but you must hunt for cheap parts
3SX Oil Cooler Kit - Core + Lines + Fittings - FMOC*-*Mitsubishi 3000GT*/*Dodge Stealth Parts (http://www.3sx.com/store/comersus_viewItemBundle.asp?idProduct=28950)

mb3000
10-09-2011, 12:51 AM
I like what Trevor did with his, I'm just waiting for my excuse!

mb7050
10-09-2011, 05:27 AM
yeah dual ftw. but I like my big ass single front mount better way simpler and cheaper solution I didn't even have to make a bracket to hold it + oem shrouding fits .Overall install was a breeze
with the oem cooler I could see temps as high as 140C even more during very hard driving .
I havenīt seen temps exceed 110c with this one, not a surprise it is about 8+ times bigger than the oem one!

http://img850.imageshack.us/img850/6162/imag0229i.jpg

J. Fast
10-09-2011, 06:51 AM
Since we're talking on the cheap... Just FYI, CX Racing sells 30 rows with with 10-AN inlet/outlet and (2) 5' 10-AN PTFE hoses for $145. Core dimension is 11" x 9" x 2".

They also sell several variations of aluminum 10-AN cores for under $75 shipped.

# Rows = Core Size / Overall Size

30 row = 11" x 9" x 2" / 13" x 9" x 2"
28 row = 11" x 8.5" x 2 / 13" x 8.5" x 2"
25 row = 11" x 8" x 2" / 13" x 8" x 2"

Lastly CX also sells billet oil filter sandwich plates with oil temp and oil pressure sending unit tap ports for dedicated gauges. I paid $75 for one.

Pretty inexpensive options.

mb7050
10-09-2011, 10:03 AM
yep and keep your eyes open too there are plenty of nice "nascar"etc cores for sale on ebay from time to time.
like this one of mine its a fluidyne cooler ~12"x~12"x~3" 12-AN I think I paid 280$ for it

green-lantern
10-09-2011, 01:14 PM
Good posts guys!

The only thing that scares me a little about aftermarket oil coolers is I would want to make sure it flows > = to the stock one. You can spin a bearing in one of these cars with a shitty oil filter cutting off flow so I've been a bit hesitant to go with one without investigating them a bit more. I've also wanted to do a remote oil filter with a bigger filter. There seems to be plenty of large remote oil filter kits that use a big V8 domestic oil filter that would work nicely.

mb7050
10-09-2011, 03:06 PM
yes I would like to do an oil filer "upgrade" with one of these https://www.cantonracingproducts.com/cgi-bin/commerce.cgi?preadd=action&key=25-826 or a similar filter . but I have heard so many bad thing about the canton filters that I donīt think I can ever use one

a dual filter setup like in the porsche 997 would be nice too

one of porsche filter vs ours .way higher psi pressure relief valve and much more flow
http://www.lotustalk.com/forums/attachments/f312/128473d1248482345-mobil-m1-103-vs-m1-203-oil-

I have been about to do it many times but never felt a real need to do it ...


http://wboil.com/images/dual-remote-by-pass.jpg

mb7050
10-09-2011, 03:42 PM
The only thing that scares me a little about aftermarket oil coolers is I would want to make sure it flows > = to the stock one. You can spin a bearing in one of these cars with a shitty oil filter cutting off flow so I've been a bit hesitant to go with one without investigating them a bit more.

thats why I went with a fluidyne cooler one of the highest rated heat transfer and efficiency numbers and should not cause pressure drops, fluidyne oil coolers are considered just as high quality as SETRAB and setrab is the top brand but ridiculously expensive IMO

J. Fast
10-09-2011, 03:57 PM
Where is this high temperature oil J. Fast?

Didn't have time to offer my opinion on this till I had some time...

The mindset in the thread was leaning towards refined petroleum motor oil and how it performs. You are correct in saying that refined motor oil is not high temp oil. However, we now have synthetics, better yet, true synthetics. True synthetic motor oils are pure chemical so they can be engineered to perform at very specific temperature and viscosity ranges. You want an oil that performs best at 200* buy it, 240*, 260, 280* and etc. You can buy synthetic oil engineered for every temperature, pressure, viscosity, and wear condition or range imaginable. Someone with some interest in how their engine behaves will know to shop for synthetic oil producing "x" oil pressure at "y" rpm when the engine oil is at "z" temperature. You can buy it that way, at least that’s how I was informed to select motor oil.

Where's the high temp oil? That's the essence of being synthetic. From the published articles I've read by Mobil-1, AMSOIL, and Shell, I feel you can purchase synthetic oil engineered to maintain its weight and performance characteristics in any temperature range you want whether it be high temp, low temp, or a combination of both. Consequently, oil selection has its compromises too. What you may benefit from in one area you will sacrifice in another. For the most part it seemed to me like the additives in full synthetics, whether it be friction modifiers, stabilizers, aeration reducers, and etc dictate the performance window.

It's my understanding every synthetic oil marketed has a published thin film oxygen performance rating, and bearing wear rating (I believe called a four ball wear test?) which outlines its oils performance under varying heat and oxygen exposures. Additionally, there's published NOACK tests which clearly illustrate brand x, y, z’s oil performance volatility based on temp, pressure, and etc. Now, if you’re going to burn your oil or exceed the operating window then by all means add a cooler.

green-lantern
10-09-2011, 04:10 PM
yes I would like to do an oil filer "upgrade" with one of these https://www.cantonracingproducts.com/cgi-bin/commerce.cgi?preadd=action&key=25-826 or a similar filter . but I have heard so many bad thing about the canton filters that I donīt think I can ever use one

a dual filter setup like in the porsche 997 would be nice too



+1 on canton, I just don't trust them. I'm sure some of the remote options are fine but I think I'd rather go another route. I think it can be done better and cheaper. Again I worry about monkeying with the stock setup too much because if I overlook something it can be engine failure. I probably will do a remote option but I just want to make sure I don't do more harm than good.

green-lantern
10-09-2011, 04:15 PM
thats why I went with a fluidyne cooler one of the highest rated heat transfer and efficiency numbers and should not cause pressure drops, fluidyne oil coolers are considered just as high quality as SETRAB and setrab is the top brand but ridiculously expensive IMO

Thanks again for the info. I'm probably going to do the same setup as yours. How much do you have in it?

green-lantern
10-09-2011, 05:12 PM
What is the biggest I can fit in the stock location? I have a FMIC so I really don't want to put it up front.

mb7050
10-09-2011, 05:13 PM
Russell proclasic hoses and fitting were something like ~150$ I didn't hunt for the best prices on the parts and russell ainīt the cheapest brand. the core was 280$ Iīm sure you could get similar results with the 150$(11x8x2 fluidyne core). Iīm fairly certain you can sidemount that one too .

Alex3000gt
10-09-2011, 05:43 PM
Good posts guys!

The only thing that scares me a little about aftermarket oil coolers is I would want to make sure it flows > = to the stock one. You can spin a bearing in one of these cars with a shitty oil filter cutting off flow so I've been a bit hesitant to go with one without investigating them a bit more. I've also wanted to do a remote oil filter with a bigger filter. There seems to be plenty of large remote oil filter kits that use a big V8 domestic oil filter that would work nicely.

For flow, what you would want to compare is pressure drop across the oil cooler. If you know the stock oil cooler's pressure drop at a given flow rate, then make sure the one you buy is less than or equal to that. Also consider the total amount of oil your system will need if you increase the size of your oil cooler.

AudibleSilence
10-10-2011, 01:24 AM
Didn't have time to offer my opinion on this till I had some time...

The mindset in the thread was leaning towards refined petroleum motor oil and how it performs. You are correct in saying that refined motor oil is not high temp oil. However, we now have synthetics, better yet, true synthetics. True synthetic motor oils are pure chemical so they can be engineered to perform at very specific temperature and viscosity ranges. You want an oil that performs best at 200* buy it, 240*, 260, 280* and etc. You can buy synthetic oil engineered for every temperature, pressure, viscosity, and wear condition or range imaginable. Someone with some interest in how their engine behaves will know to shop for synthetic oil producing "x" oil pressure at "y" rpm when the engine oil is at "z" temperature. You can buy it that way, at least that’s how I was informed to select motor oil.

Where's the high temp oil? That's the essence of being synthetic. From the published articles I've read by Mobil-1, AMSOIL, and Shell, I feel you can purchase synthetic oil engineered to maintain its weight and performance characteristics in any temperature range you want whether it be high temp, low temp, or a combination of both. Consequently, oil selection has its compromises too. What you may benefit from in one area you will sacrifice in another. For the most part it seemed to me like the additives in full synthetics, whether it be friction modifiers, stabilizers, aeration reducers, and etc dictate the performance window.

It's my understanding every synthetic oil marketed has a published thin film oxygen performance rating, and bearing wear rating (I believe called a four ball wear test?) which outlines its oils performance under varying heat and oxygen exposures. Additionally, there's published NOACK tests which clearly illustrate brand x, y, z’s oil performance volatility based on temp, pressure, and etc. Now, if you’re going to burn your oil or exceed the operating window then by all means add a cooler.

Or you could just read a Technical Data Sheets and not worry about the conditions and approximations of the test conditions. You are correct, the additive package is key. Some packages are better for engine metals than others, others are best for deposits..

p.s. The W in an oil rating doesn't stand for weight it stands for Winter. You can lose performance from going too thick.. I personally wouldn't go lower than 5w30..but I've seen some 0's out there o.0 I've never heard of someone choosing oil based on a certain pressure at a certain temp..

If folks want an oil thread..I'll start one. Then again what do I know, I just work for an oil company.

mb3000
10-10-2011, 02:50 AM
Or you could just read a Technical Data Sheets and not worry about the conditions and approximations of the test conditions. You are correct, the additive package is key. Some packages are better for engine metals than others, others are best for deposits..

p.s. The W in an oil rating doesn't stand for weight it stands for Winter. You can lose performance from going too thick.. I personally wouldn't go lower than 5w30..but I've seen some 0's out there o.0 I've never heard of someone choosing oil based on a certain pressure at a certain temp..

If folks want an oil thread..I'll start one. Then again what do I know, I just work for an oil company.

Start one.

J. Fast
10-10-2011, 08:48 AM
If folks want an oil thread..I'll start one. Then again what do I know, I just work for an oil company.

Yes please that would be great! If you look at 1 synthetic oil engineering company let's say, AMSOIL. They must have 100 different oils. Take for instance... just the 30 weights. What's the difference between their 30 weight synthetics? They carry all these synthetic 30 weights for gas engines from 0 winter weight to straight 30 weight. vvvv LOL vvvv

1. Signature Series
2. Synthetic SAE
3. Synthetic European Car Formula
4. Dominator Racing Oil
5. Z-Rod SAE
6. OE Synthetic
7. XL Synthetic Extended
8. Synthetic Advanced SAE
9. Synthetic Series 3000
10. SAE 30 HD

:lo5l:

a2j
10-10-2011, 09:32 AM
I spent about $100 for my oil cooler setup (ebay). Drove to work this morning with temps 155-160 F. On Saturday's cruise - 180F. imho, its worth it. I don't know what temps were with stock cooler and can't even imagine temps with no cooler. 260F?

AdamVR4
10-10-2011, 11:52 AM
For flow, what you would want to compare is pressure drop across the oil cooler. If you know the stock oil cooler's pressure drop at a given flow rate, then make sure the one you buy is less than or equal to that. Also consider the total amount of oil your system will need if you increase the size of your oil cooler.


Unfortunately, most aftermarket automotive part manufacturers do not provide consumers with pressure drop vs flow rate data. Is there a company out there that does?

i3igpete
10-10-2011, 03:27 PM
Setrab does, see the graph "oil pressure drop in tubes of different lengths". The X axis is normalized oil flow rate.

http://www.setrab.com/uploads/media/Product_brochure_STD_and_COM_english.pdf



I've never heard of someone choosing oil based on a certain pressure at a certain temp..


see section 3.3. section 3.4 is more applicable for car engines but unfortunately the data is hard to come by except for the largest companies with really good ($) test equipment.

http://books.google.com/books?id=xBMgKfyHs4AC&pg=PA26&lpg=PA26&dq=ubbelohde+walther&source=bl&ots=GYkniy_Go9&sig=SNi8ndLD7vl3CT8y0ftMLGmGhC0&hl=en&ei=NzmTTq3pJKKnsAKNqeXCAQ&sa=X&oi=book_result&ct=result&resnum=8&ved=0CFYQ6AEwBw#v=onepage&q&f=false

AdamVR4
10-10-2011, 03:53 PM
Setrab does, see the graph "oil pressure drop in tubes of different lengths". The X axis is normalized oil flow rate.

http://www.setrab.com/uploads/media/Product_brochure_STD_and_COM_english.pdf


Nice find, thanks.

Alex3000gt
10-10-2011, 07:08 PM
Unfortunately, most aftermarket automotive part manufacturers do not provide consumers with pressure drop vs flow rate data. Is there a company out there that does?

Ah, damn. They may keep that info in-house, but I am surprised it would not be provided to the consumer. It wouldn't be too difficult to measure, but by that point you have already purchased the item.

An item related to pressure drop that you could eyeball yourself is cross sectional area of the oil tubes in the heat exchanger, multiplied by the number of tubes. There are other factors, but that could get you started.

Alex3000gt
10-10-2011, 07:10 PM
Setrab does, see the graph "oil pressure drop in tubes of different lengths". The X axis is normalized oil flow rate.

http://www.setrab.com/uploads/media/Product_brochure_STD_and_COM_english.pdf




see section 3.3. section 3.4 is more applicable for car engines but unfortunately the data is hard to come by except for the largest companies with really good ($) test equipment.

Lubricants and Lubrication - Theo Mang, Wilfried Dresel - Google Books (http://books.google.com/books?id=xBMgKfyHs4AC&pg=PA26&lpg=PA26&dq=ubbelohde+walther&source=bl&ots=GYkniy_Go9&sig=SNi8ndLD7vl3CT8y0ftMLGmGhC0&hl=en&ei=NzmTTq3pJKKnsAKNqeXCAQ&sa=X&oi=book_result&ct=result&resnum=8&ved=0CFYQ6AEwBw#v=onepage&q&f=false)

Win, good find. Now all we need is our baseline, what is the stock oil cooler's pressure drop at a given flow rate.

AudibleSilence
10-11-2011, 02:06 AM
see section 3.3. section 3.4 is more applicable for car engines but unfortunately the data is hard to come by except for the largest companies with really good ($) test equipment.

Lubricants and Lubrication - Theo Mang, Wilfried Dresel - Google Books (http://books.google.com/books?id=xBMgKfyHs4AC&pg=PA26&lpg=PA26&dq=ubbelohde+walther&source=bl&ots=GYkniy_Go9&sig=SNi8ndLD7vl3CT8y0ftMLGmGhC0&hl=en&ei=NzmTTq3pJKKnsAKNqeXCAQ&sa=X&oi=book_result&ct=result&resnum=8&ved=0CFYQ6AEwBw#v=onepage&q&f=false)

Interesting, though to your point I've never seen that measurement on any industry standard TDS. Most companies break it down to VI and give you the sheer #s if that. What would said information tell you (personally) that the VI @ temp X doesn't in relation to what is best for your car at a motorsport event?? Most of the engineers that I deal with seem to be good to go with info readily available? -listens intently-

i3igpete
10-11-2011, 02:29 AM
shear thinning is a very elusive unknown when it comes to bearing modelling. a lot of elasto-hydrodynamic codes i'm familiar with have a few "recommendations" based on literature, but that's simply because they can't get the data from oil companies. Could be a lack of perceived demand, or lazyness, but very likely both. I've had some customers say it's like pulling teeth trying to get info from their oil suppliers, you need to be a major OEM for them to even give you the time of day.

AudibleSilence
10-11-2011, 03:17 AM
We don't even publish our TDS and MSDS files... I can see that. We get obvious orders from the competition and we ourselves test their stuff to make sure it meets their claimed spec. It's catty as all hell. You would love our Q school.

J. Fast
10-11-2011, 09:33 AM
Interesting, though to your point I've never seen that measurement on any industry standard TDS. Most companies break it down to VI and give you the sheer #s if that. What would said information tell you (personally) that the VI @ temp X doesn't in relation to what is best for your car at a motorsport event?? Most of the engineers that I deal with seem to be good to go with info readily available? -listens intently-

Does your company use this model?
Applied tribology: bearing design ... - Michael M. Khonsari, E. Richard Booser - Google Books (http://books.google.com/books?id=opn-gi762-AC&lpg=PP1&dq=Applied%20Tribology%2C%202nd%20Edition&pg=PA23#v=onepage&q=Applied%20Tribology,%202nd%20Edition&f=true)
Is table 2.4 Correct?

AudibleSilence
10-11-2011, 02:19 PM
Does your company use this model?
Applied tribology: bearing design ... - Michael M. Khonsari, E. Richard Booser - Google Books (http://books.google.com/books?id=opn-gi762-AC&lpg=PP1&dq=Applied%20Tribology%2C%202nd%20Edition&pg=PA23#v=onepage&q=Applied%20Tribology,%202nd%20Edition&f=true)
Is table 2.4 Correct?

My company does the HTHS testing (viscosity at certain temp/pressure) yes... I wasn't paying attention to what the test actually was, I just knew what we called the resulting info, my mistake. Mobil does, we do..not sure about Shell...I have never had a customer ask me about the HTHS spec, 90% of the time they just want to know the operating temps. . As I understand it, this info is useful in motorsport for things like picking the right viscosity/oil for a things like piston rings and such. I've never heard of it being used as such, but that's what I gather. Pete can you clarify?

Intropy
10-12-2011, 01:32 AM
This ended up being one of the most interesting threads on 3sgto in a while. What can I delete next? :lo5l:

Boomer3000
10-12-2011, 02:43 AM
put Potatos in it.. it cools it down so well..

J_Parker
04-03-2012, 01:30 PM
What method did you use to delete yours? I deleted mind the other day, but completely overlooked the fact that I can't just simply plug the holes. I was thinking that I could cut the banjo ends off of the stock cooler, flair the opening and loop them. Does this seem like something that could be a good temporary solution until I get my N/A filter housing here??

Intropy
04-03-2012, 02:24 PM
Well, to be fair, I added a new oil cooler, this was mostly fun / flamebait. ;) But when it was leaking, I installed AN adapters into the filter housing and looped a short piece of -10AN hose.

green-lantern
04-03-2012, 04:28 PM
Well, to be fair, I added a new oil cooler, this was mostly fun / flamebait.

You know you could have got 25 years for that in Arizona. :lo5l:

mcshooter
04-03-2012, 11:02 PM
i douth you have anything to worry about deleting the oil cooler. the first thing iam doing to the gm l99 ls engine iam putting in mikes 1970 gto is to delete the oil cooler. the reason the 2011 camaro ss uses one is the engine is highly confined . all folks who are using the l99 and ls3 are also deleting the oil cooler. if iwas worried about it i would get one of the bigger oil pans i see for the 3s .. some car forumns have a bunch of factory emgineers on board that would have a answer but i dont think anyone here would know for sure since our cars are so old. do we have any mitsu engineers on our forumn???

J_Parker
04-04-2012, 12:18 AM
Well, to be fair, I added a new oil cooler, this was mostly fun / flamebait. ;) But when it was leaking, I installed AN adapters into the filter housing and looped a short piece of -10AN hose.

I actually just bit the bullet and bought some fittings after work, so I did the same, it works quite well :) ...And there's no more ugly leaking cooler hanging off the side of my car!

J. Fast
04-04-2012, 12:18 AM
An excellent 10 Chapter Read: >>> Motor Oil University - Bob is the Oil Guy (http://www.bobistheoilguy.com/motor-oil-101/) <<<


Motor Oil University, Bob is The Oil Guy Chapter Five – Let’s use top gear.

Let’s go racing. I will discuss driving in traffic jams in the Florida summer as well as racing in Sebring though there is no commonality. People lump these two driving situations together but there is no overlap.

On the race track one usually uses all the BHP their engine can give them. You briefly step on the brakes for the corner then put the pedal to the metal the rest of the time. Your oil will get up to 302°F, but your cooling system is around 212°F. The engine produces tremendous heat but can only pass it off so fast to the cooling system. There is a lot of air moving past the cooling radiator so the antifreeze / coolant is able to get rid of the extra heat from this part of the system with relative ease.

The temperature of oil on your gauge is not as hot as it really gets. This temperature is an average with oil from different parts of the motor. Some parts are hotter than others. It is said that some of the oil gets as hot as 400° or 500°F in these racing situations.

In an earlier section I said that thicker oils are usually needed in racing situations but not necessarily. Remember that a major function of oil is to cool the inside of your engine. In ASTM D 4485 3.1.4: “Terminology: Engine oil- a liquid that reduces friction and wear between moving parts within an engine, and also serves as a coolant.” Since the oil with a viscosity of 10 cS at 212°F thins to a viscosity of 3 cS at 302°F we will get more flow. The pressure will go down some as well. This is OK as long as we have a minimum of pressure to move the oil.

This increased flow will result in increased cooling by the oil. This is a good thing. You would probably want more oil flow in these situations and you get it. The hotter oil thins and this increases flow. The higher flow works harder to separate the engine parts that are under very high stress. It all works out for the better. Higher revving engines need thinner oils. You do not necessarily need to go to a thicker oil while racing. Only experimentation will tell.

The best way to figure out what viscosity of oil you need is to drive the car in the conditions you will use. Then use the oil viscosity that gives you 10 PSI per 1,000 RPM under those circumstances. For some reason very few people are able to get this simple principal correct. I cannot explain further.

These same rules apply to engines of any age, loose or tight. Just because your engine is old does not mean it needs a thicker oil. It will need a thicker oil only if it is overly worn, whether new or old. Yet the same principals of 10 PSI per 1,000 RPM still apply. In all cases you need to try different grade oils and see what happens. Then choose the correct viscosity.

I used 0W-20 in my Ferrari 575 Maranello. It had over 5,000 miles on the clock. There will be a day (my estimate is 50,000 miles) when one will have to go to a 0W-30. In the future one will have to increase the viscosity to a 0W-40, then a 0W-50, maybe. You should use whatever it takes to get 75 PSI at 6,000 RPM during the lifetime of the engine. This formula works in all situations.

Some people have tried this and occasionally get a somewhat low oil pressure while at idle. This is fine. There is no stress on parts at idle, the smallest oil flow will do the trick. It is at higher RPM where more BHP is produced. This is where we need the flow. Remember that Ferrari uses 75 PSI at 6,000 RPM as the place to test your oil viscosity needs. If your oil gives this value under your driving conditions then your lubrication system has been maximized. Period.

Do not go 5,000 miles with the same oil if you are racing your car. You should change the oil every 1 or 2,000 miles. If you drive your car around town then you need to change the oil for that situation. Use racing oil on the track and urban oil around town. The best situation as described by Ferrari is to use the 0W-40 around town and the 10W-60 “racing oil” on the track. It has to be that “hot” track though. A compromise situation would be to use the 5W-40 for both but this may not be optimal. Certainly, if you are just an urban driver as me use the 0W-40 or even a thinner oil as I do in my Maranello. Again, I used the 0W-20 grade.

FYI. The Formula 1 cars that run at 15,000 RPM and higher use straight 5 and 10 grade oils.

Now let me discuss what people think is a similar situation to racing. That is hot summer traffic jam driving. Your car should be able to handle this. If you have problems then you have a problem with your car, most likely in need of a cooling system overhaul.

When you drive that car down the road mid-winter in upstate New York or mid-summer in Florida the engine and oil temperatures will be around 212°F. But your Florida vacation is suddenly altered by a hurricane. You have to get out of Tampa, but so do a million other people. It is now 95°F and you are in a snarl. Everyone thinks they need a thicker oil for this situation. This is false.

Your engine is not producing much heat at low RPM and low BHP output. The production of heat is relatively slow. It can easily be transmitted to your cooling system. The problem is that your cooling system has trouble getting rid of the heat. The oil and the coolant will slowly rise in temperature. They both rise together. The increase is no big deal for your oil. It goes to 220°, then 230°F. The problem is that the cooling system can only handle heat up to 230°F. After that you overheat the cooling system and the car must be shut off. The oil never got that hot, It was just that the water got a little hotter than its system design.

You now see that overheating in traffic is a cooling system problem and not an oil system problem. Do not change to a thicker oil based on your traffic situation.



That pretty much summed up why an oil cooler isn't necc for a BHP DD car. 0w-50 produces 75 psi at 500 degrees and it doesn't burn. I dont think you can get oil that hot by driving to the grocery store. Likewise, I don't think you could get it over that temp on the track and risk spinning a bearing or damaging turbos or journals before you overheat or pop the headgasket. Even though the thread was a sham and quite silly, learning what I have from the racing community and BITOG, I pretty much think you could delete the oil cooler if using full syntheic oil vs. mineral based oil and see no ill effects.

BLACK94TT
04-05-2012, 06:10 AM
What is the biggest I can fit in the stock location? I have a FMIC so I really don't want to put it up front.

I'm checking into a 11x8x2 Fluidine core. I wonder if it'll fit in the sidemount position.

BLACK94TT
04-05-2012, 07:07 AM
Were you able to reinstall the crash bar?
yeah dual ftw. but I like my big ass single front mount better way simpler and cheaper solution I didn't even have to make a bracket to hold it + oem shrouding fits .Overall install was a breeze
with the oem cooler I could see temps as high as 140C even more during very hard driving .
I havenīt seen temps exceed 110c with this one, not a surprise it is about 8+ times bigger than the oem one!

http://img850.imageshack.us/img850/6162/imag0229i.jpg

VR4Play
04-11-2012, 04:26 PM
Oh, I am reading...but to me, deleting an item like an oil cooler because it is leaking is not the correct course of action. While things like the clutch booster tank can be removed without ill effects, things like the oil cooler are there for a very good purpose and IMO shouldn't be deleted if leaking, they should be fixed. Unless it's a temp thing to limp around out of boost until you can afford the time or money to fix it correctly.

-Chris
The other issue not mentioned here is that Mitsu/Dodge felt that a cooler was necessary even given the cushy way ("GT") they felt the car would be driven. Even dogging a stock TT will put you into boost from time to time. Add high ambient temps and you may have problems. Granted original design was prior to common use of synthetics, but still a precaution to ensure a semblance longevity. I have a hard time believing that someone (1) that owns a TD05 car wouldn't dip into the TT DD; (2) that wrenches his own car wouldn't find it just as easy to fix the cooler as removing it; (3) a serious motor-head would bring this up wasting our time if he was just trying to 'mix things up'.