View Full Version : Starting issue
dsmnoob91
10-02-2011, 08:42 PM
My sl has been doing a lot better lately up until recently not it has a new issue where it does not like to start it will crank and crank and crank like it has no spark of you unplug the ignition module and plug it back in right away it starts but if you don't let it warm up for a solid minute it stalls out right away it also has a check engine light not sure what for. After it's been running and you shit it off and let try turning it back on if you don't give it gas it starts for a second and stalls but if you give it gas it will idle and run good but it also feels slower now any ideas? I was thinking mass airflow for some reason or ignition module And remember it is no longer turbo any more
Steve '92ES
10-02-2011, 09:43 PM
I'd start by reading the codes. No sense guessing when the car's trying to tell you something...
Stealth 316 - Reading Diagnostic Codes - 1991-1993 3S models (http://www.stealth316.com/2-diagcodes91-93.htm)
dsmnoob91
10-03-2011, 04:37 PM
I pulled the ecu out and it smells like crap two of the caps have black stuff around them... Think that is my issue?
Steve '92ES
10-03-2011, 07:46 PM
Yep. It's a known issue with our cars, the capacitors go bad and leak causing all kinds of problems.
Try contacting this guy: rymer21280 (Eric Rymer rymer@wavecable.com)
I don't know him but he has a good reputation for fixing ECUs.
dsmnoob91
10-06-2011, 11:40 AM
I sent him a email still waiting on a response
Alex3000gt
10-11-2011, 12:24 AM
I sent him a email still waiting on a response
Can you source an ECU locally to test the theory that yours is fried and causing the issue?
ictponder
10-12-2011, 03:24 PM
Can't the capacitors just be replaced and be done with it or do they cause more problems when they leak? Soldering is fairly easy to do.
Gamerse
10-14-2011, 01:43 AM
^depends on if the electrolytes from the capacitors damage any of the other components or PCB. There are probably 3 or 4 how-tos floating around out there. Mitsu undersized capacitors on every module in the car, the auto climate control, and ECS both die due to undersized capacitors.
Steve '92ES
10-14-2011, 09:16 PM
Mitsu undersized capacitors on every module in the car, the auto climate control, and ECS both die due to undersized capacitors.
Actually that's not true. The "Bad Cap" problem ran rampant through the electronic industry and affected just about everything from PCs to us (automotive electronics). As a matter of fact those How-To's you mention all tell you how to put THE EXACT SAME VALUE back in. This is not a "Mistu" problem, it goes waaayyy deeper than that. Here's a little perspective from a motherboard repair house: Badcaps.net - What Causes This (http://www.badcaps.net/pages.php?vid=4)
Not trying to jump on you, just putting the blame where it belongs.... ;)
Gamerse
10-14-2011, 10:16 PM
From your article you recommended. " Nowadays, it just boils down to corporate bean counters cutting corners to save money by using shoddy components." " a VERY popular monitor manufacturer has been plagued with RMA's on some of their monitors" Note this website sells capacitors and capacitor kits as a fix for things, and was started in 2003. Furthermore, they do not specify the date or source of their information of these rouge capacitors. The sight is owned by a computer repair shop established in 93. This is hardly a reputable source for information on mitsubishi technology, and their source of components. The closest he would come to it is repairing a large TV.
No "EXACT SAME VALUE" caps in my how to or discussion threads. (capital letters are unnecessary) I'm not sure how to take the not jumping thing, this is mitsu's fault. I have dealt with their technology on land and air, they have engineering problems. Saying there was a rash of bad capacitors is vague blanket statement.
This is and was there fault. They used Caps that were not capable of handling the heat. You compensate for there oversight by replacing the capacitors with units of the same freuqency (capacitance) but a higher voltage. I could quote sights with all the math, and explain it here, but it would serve no purpose. So, i found a guy that does avionics radio repair and shares his unbiased, simplified information for free.
"Three sure ways to kill an electrolytic capacitor:
1.Overvoltage: If the specified voltage is exceeded, current will leak through the isolation, not in a slow way that might regenerate weak areas, but violently, creating hotspots where additional break-down occurs. The danger of explosion is imminent.
2.Reversed polarity: As described, the inverse of regeneration = self destruction, will occur. If the applied voltage is near the normal (right polarity) working voltage, break-down is quick and violent. The effect of a low inverse voltage might be reversible.
3.Heat. Heat shortens the life of an electrolytic capacitor. A good rule of thumb is that every 10deg C over 85 will cut the life expectancy in half."
Electrolytic capacitors (http://www.hans-egebo.dk/Tutorial/electrolytic_capacitors.htm)
"As already mentioned, never go below the voltage rating of the original part."
Electrolytic capacitors (http://www.hans-egebo.dk/Tutorial/electrolytic_capacitors.htm)
I didn't think I needed to explain all the information related to the problem, but next time I guess I'll have to have a spill about being a Avionics repair technician that has repaired mistubishi autopilots, mitsubishi aircraft, and the above mentioned ECS and Auto Climate Control. (did I mention Dave57 and myself were the first to collaborate and repair the auto climate control, Hell, black stealth wrote a wiki from our info Auto climate control, the ticking time bomb... - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f128/auto-climate-control-ticking-time-bomb-407591/)) ECU ECS Climate Control Capacitor repairs - History - 3SI Wiki (http://www.3si.org/wiki/index.php?title=ECU_ECS_Climate_Control_Capacitor_ repairs&action=history)
It is his wiki, so he sourced parts his way. I had no input on it.
Not trying to jump on you, just putting the blame where it belongs....
Nightwolf
10-14-2011, 10:39 PM
^ tis true. I worked avionics for 4yrs in the navy and saw some really dumb stuff on circuit boards. technical changes came to us once a quarter and things like this where part of those changes at least once or twice a year. Part of the problem has to do with component aging and board aging. as boards and components age and accumulate corrosion their resistance values increase. this in turn changes the voltage drop across individual components. it usually isnt much but when using close tolerance components any change can cause problems. electrolytic capacitors are cheap and used extensively bc of their low price. this doesnt mean they are crap it just means they arent built to tolerate much variance in input.
Steve '92ES
10-15-2011, 12:30 AM
Whoa!!! I really didn't mean to start an argument.
You hear so many people dumping on our cars. They're too slow. They're too heavy. They break all the time. Adding they f*cked up the electronics to the list just seems unfair. That's the part I was trying to defend, not pick a fight about electronics.
I do however disagree with you that this is solely Mitsu's fault, or that they "undersized the caps"
There was, back in the '90s, a rampant problem with defective caps. This is widely known in the industry. The link I put up is just one of many that discuss it.
This went beyond the usual aging problem inherent with all electrolytic caps, and I believe that is the major cause of our failing caps.
Could Mitsu have used higher heat ratings? Sure. However without heat measurements to prove it I don't think it's a fair statement to claim that's the cause. Besides, "undersized" and "under rated" are two different things.
Nightwolf
10-15-2011, 01:09 AM
cant speak for gamerse but i wasnt trying arguing i was just explaining how electronic devices built with close tolerances leave little room for aging and corrosion. using slightly higher tolerance components generally yield longer lasting products.
end electronics theory class.
and i dont blame Mitsu i blame the cap manufactures. crap products used in another product leads people to hold the end product manufacturer responsible when they usually dont have knowledge of the problem at the time of manufacture.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.