PDA

View Full Version : Let's talk fuel lines.



OBXBoost
09-27-2011, 03:01 PM
I'm getting close to where I need to be with my car. I want to chose fuel line for it. I don't like the look of the stainless steel braided exterior but know I want it in there. Is there a fuel line out there that is stainless steel braided but has a rubberized exterior?

On the next note, I have the Jackhammer/Tackhammer/Jack/Wayne dual fuel pump assembly. Two Aeromotive Stealth (340lph) drop in pumps will be going in there. I have stock (for now) fuel rails. I also have AEM AFPR and Jackhammer/Tackhammer/Jack/Wayne FPG going on to each rail.
From my understanding, the front rail will be the feed rail with FPG and the back rail will be the return off the AFPR to the tank. I'm going to be running 1000cc injectors. (For those wondering, I have an AEM EMS too.) My question is, how much length of fuel line should I buy, and what size(s) will I need? Also, I need to buy a fuel filter, any recommendations?

Thanks :)

mb3000
09-27-2011, 05:01 PM
For the tank to filter I would get about 10'.

Chris@Rvengeperformance
09-27-2011, 06:12 PM
keep in mind not all "stainless steel" line is better than stock, some is a lot worse. Unless you really need it I would keep as much stock line as possible. People have made a TON of power on the stock lines on gas, including dual pumps.

If you get anything get some of the black nylon covered teflon lined hosed. If I was going to do it I'd run solid line from the flex line at the rear tank to the front. That is the safest.

Don't get standard stainless braided line unless you want your car to smell like a gas station all the time.

Woz
09-27-2011, 06:20 PM
If I was doing your setup I would do each fuel rail seperate and run a feed line to each and a return line from both. then you would need 2 FPR's. That's my opinion but with 1000cc, I would at least get 10AN minimum.

IPD
09-27-2011, 08:48 PM
If I was doing your setup I would do each fuel rail seperate and run a feed line to each and a return line from both. then you would need 2 FPR's. That's my opinion but with 1000cc, I would at least get 10AN minimum.

-8 AN is sufficient for dual feeds. i also second the idea of a feed for each line, as with large fuel flow, running the rails in series can create problems. you still only need 1 FPR, you just need to Y the fittings into it or get a dual-in, single-out FPR.

i don't even think chris's 1600cc monster is running larger than -8AN feeds. stock is a single -6AN. -8AN is sufficient for pretty much everything. i think -10AN is overkill as a dual-feed solution.

p.s.
i will be running BLACK stainless braided lines.

stealthII
09-27-2011, 09:44 PM
If you do this, make sure you get Teflon lined hoses. I had non-Teflon hoses and they would permeate gas and would stink up the garage.

mb3000
09-28-2011, 12:20 AM
8AN tank to filter, 6AN filter to rail, stock feed as return. Dual feed is nice but don't be like me.

Austin@STM
09-28-2011, 12:40 AM
STM - RUSSELL PROCLASSIC HOSE | BLACK NYLON / BLUE ACCENT (http://www.streettunedmotorsports.com/parts/russell_pro_classic_black_blue_hose.htm)

IPD
09-28-2011, 02:43 AM
If you do this, make sure you get Teflon lined hoses. I had non-Teflon hoses and they would permeate gas and would stink up the garage.

important to note. unlike what forest said, this is the root cause.

Permanent grin
09-28-2011, 05:20 AM
important to note. unlike what forest said, this is the root cause.

I agree. I had to change out my stainless braided for stainless braided PTFE for exactly this reason.

For the record, my current build will run 2 x -6AN from the tank with twin filters and use the stock feed line as the return. We did look at -10 but all of the fuel filters we could find only had -8 fittings maximum, so would have made the -10 pointless.

André

IPD
09-28-2011, 07:53 AM
so the guy with dr1400's is only running -6AN. kinda proves my point about -10AN being WAY overkill.

J. Fast
09-28-2011, 08:55 AM
I'm getting close to where I need to be with my car. I want to chose fuel line for it. I don't like the look of the stainless steel braided exterior but know I want it in there. Is there a fuel line out there that is stainless steel braided but has a rubberized exterior?

On the next note, I have the Jackhammer/Tackhammer/Jack/Wayne dual fuel pump assembly. Two Aeromotive Stealth (340lph) drop in pumps will be going in there. I have stock (for now) fuel rails. I also have AEM AFPR and Jackhammer/Tackhammer/Jack/Wayne FPG going on to each rail.
From my understanding, the front rail will be the feed rail with FPG and the back rail will be the return off the AFPR to the tank. I'm going to be running 1000cc injectors. (For those wondering, I have an AEM EMS too.) My question is, how much length of fuel line should I buy, and what size(s) will I need? Also, I need to buy a fuel filter, any recommendations?

Thanks :)


I'm getting close to where I need to be with my car. I want to chose fuel line for it. I don't like the look of the stainless steel braided exterior but know I want it in there. Is there a fuel line out there that is stainless steel braided but has a rubberized exterior?

On the next note, I have the Jackhammer/Tackhammer/Jack/Wayne dual fuel pump assembly. Two Aeromotive Stealth (340lph) drop in pumps will be going in there. I have stock (for now) fuel rails. I also have AEM AFPR and Jackhammer/Tackhammer/Jack/Wayne FPG going on to each rail.
From my understanding, the front rail will be the feed rail with FPG and the back rail will be the return off the AFPR to the tank. I'm going to be running 1000cc injectors. (For those wondering, I have an AEM EMS too.) My question is, how much length of fuel line should I buy, and what size(s) will I need? Also, I need to buy a fuel filter, any recommendations?

Thanks :)

My setup is very similar to yours. I'm running dual walbro with 8-AN feed and 6-AN return. FIC 1150CC injectors.

To answer your question, you will need 15 feet of fuel line from the tank to the fuel rail leaving about 1ft extra for cutoff and routing at the hanger and firewall. It's 11ft under the body from the hanger assembly following the OEM lines to the fuel filter.

My setup required 21' of 6 braided, 14' of 8 braided, (2) 6-6-8 "Y", (1) 6-6-6 "Y", (2) 6-AN DBO anodized check valves, (4) OEM fuel rail socket to 6-AN fitting, (11) 6-AN anodized straight fittings, (3) 6-AN anodized 90's, (2) 6-AN anodized 45's, (4) 8-AN anodized straight fittings. Aeromotive FPR, (1) fuel guage, (7) 3/4" silco anti vibration fuel strap, (7) 1/2" silco anti vibration fuel strap, (1) OTP 45 micron billet fuel filter with 8-AN inlet/outlet, Anodized Bullet heatsink 6AN inlet/outlet, (2) fuel tank clunks, Cost for everything including pumps and stainless dual FP hanger was approx $1500.

Permanent grin
09-28-2011, 09:23 AM
so the guy with dr1400's is only running -6AN.

Almost, I am running two -6AN as feeds and using the stock feed as the return.

André

Chris@Rvengeperformance
09-28-2011, 10:47 AM
important to note. unlike what forest said, this is the root cause.

what the fuck are you talking about? I mentioned to get telfon lines hoses because of that.

I wish you would post about things you have a clue about, but then I guess you wouldn't post anything except the best xbox games.

AdamVR4
09-28-2011, 11:28 AM
I agree. I had to change out my stainless braided for stainless braided PTFE for exactly this reason.

For the record, my current build will run 2 x -6AN from the tank with twin filters and use the stock feed line as the return. We did look at -10 but all of the fuel filters we could find only had -8 fittings maximum, so would have made the -10 pointless.

André

That's not true. Pressure drop is a function of flow diameter AND length. A -10 system with a -8 filter has less pressure drop than a -8 system with a -8 filter.

Are you guys really running 1 pump and 1 AFPR for each bank? Am I the only one that thinks this is dangerous and unnecessarily complex?

i3igpete
09-28-2011, 11:54 AM
I agree, if a pump goes out with a common feed line, you will at least be able to limp it home.

Also, adam is right. see:
http://www.pressure-drop.com/Online-Calculator/index.html


two 255 wallys going thru a single 15ft of -6AN line comes out to be a 2.6 psi pressure drop. a single -10AN line gives a 0.22 psi pressure drop. Add in a few more psi due to losses in bends. That means for the same rail pressure, you need more pressure at the pump, which makes them more inefficient and reduces their life.

Sin'sVr4
09-28-2011, 12:00 PM
im running the same setup that austin ran....(actually its his, i bought it from him). I am using dual wally's with a custom made hanger. -8an to -6an. magnifek!

AdamVR4
09-28-2011, 12:05 PM
im running the same setup that austin ran....(actually its his, i bought it from him). I am using dual wally's with a custom made hanger. -8an to -6an. magnifek!

So a short segment of -6 from each pump into a single -8 line all the way to the rails, where it splits to -6?

Chris@Rvengeperformance
09-28-2011, 12:13 PM
wasn't trevor running 26+ PSI on his GT42 setup before he upgraded his lines due to insufficient fuel flow? It seems silly to over complicate things when not necessary.

on paper bigger lines look like a huge improvement, but in reality I don't think a couple lbs of fuel pressure really add up to all that much as long as you have a little more pump than you need.

-8 is pretty much as big as anyone needs.

AdamVR4
09-28-2011, 12:29 PM
-8 is pretty much as big as anyone needs.

Even on e85? I haven't done any research, but when I upgrade fuel lines, it would be nice to have some fuel flexibility.

Chris@Rvengeperformance
09-28-2011, 12:30 PM
Even on e85? I haven't done any research, but when I upgrade fuel lines, it would be nice to have some fuel flexibility.

I think IPO is running -8 with 4 fuel pumps IIRC.

Permanent grin
09-28-2011, 12:31 PM
No guys, you got me wrong. Dual hanger with hot wired denso's and -6an fittings to 2 -6anlines to 2 fuel filters then 2 -6an lines pressure balanced with 2 T pieces joining the 2 lines to 2 fuel rails to 2 -6an pipes to single kinsler fuel pressure regulator with 2 -6an inputs to -8an return (we were going to use stock feeds for this but changed it my mistake) All boosted by a kb boost a pump. nitrile lines were used throughout which have a slightly larger internal diameter than regular lines anyway.

André

OBXBoost
09-28-2011, 01:06 PM
so my original idea of running one short length from each pump into a Y fitting, that then feeds a larger line, goes into a fuel filter, which then goes into the Fuel Pressure guage, which is attached to the front bank fuel rail, then exits through the 3SX loop pipe to the rear fuel rail, which then exits through the AEM AFPR and uses the stock return line to the tank will NOT be adequate enough?

That was my original idea. Sorry for the long ass run on sentence, but I figured the commas would break it up enough to understand.

Chris@Rvengeperformance
09-28-2011, 01:22 PM
should work, but you should use the stock feed as your return line or it may get overrun. you can probably tune around it, but why bother if you are going to all that trouble.

DocWalt
09-28-2011, 01:41 PM
Yep, if you're gonna do that definitely use the stock feed as the return line. Also, you have to use the PTFE lines or your car will smell constantly.

AdamVR4
09-28-2011, 02:24 PM
Yep, if you're gonna do that definitely use the stock feed as the return line. Also, you have to use the PTFE lines or your car will smell constantly.

Yeah, I agree with this. I used SS lines back in the day to go from dual Walbros to stock lines, knew I didn't have any leaks, and just got used to the smell (hell, I kind of like it because I associate it with my car running, lol).

mb3000
09-28-2011, 04:52 PM
The fumes aren't that bad, unless your garage has been closed for a couple days! :barfaway:

J. Fast
09-29-2011, 09:07 AM
So a short segment of -6 from each pump into a single -8 line all the way to the rails, where it splits to -6?

^^That's what my setup is. ^^ -8 under the frame, 8-6-6 "Y" just before the rails, 6-6-6 "Y" just after.


so my original idea of running one short length from each pump into a Y fitting, that then feeds a larger line, goes into a fuel filter, which then goes into the Fuel Pressure guage, which is attached to the front bank fuel rail, then exits through the 3SX loop pipe to the rear fuel rail, which then exits through the AEM AFPR and uses the stock return line to the tank will NOT be adequate enough?

Put the gauge after the rail, after the fuel has been demanded, and after you have completed all your branch connections where the line pressure is equalized. For instance, if you're using a "Y" and going from a 2 line down to one single line, make sure you give the system the room it needs to equalize the line pressures at the union.

Don't use "T"'s, at all. "T" takes about 4 feet of line after the "T" to equalize the pressure, and you get a huge pressure drop from the 90 in one direction. Put it before the fuel rail without 3 feet and I guarantee you will see a 1 point AFR drop between banks.



No guys, you got me wrong. Dual hanger with hot wired denso's and -6an fittings to 2 -6anlines to 2 fuel filters then 2 -6an lines pressure balanced with 2 T pieces joining the 2 lines to 2 fuel rails to 2 -6an pipes to single kinsler fuel pressure regulator with 2 -6an inputs to -8an return (we were going to use stock feeds for this but changed it my mistake) All boosted by a kb boost a pump. nitrile lines were used throughout which have a slightly larger internal diameter than regular lines anyway.

André

Why two filters and two lines? Sounds more expensive that way? I agree with what someone mentioned, with one main feed, if you lose a pump you can still drive it home.

You guys feeding the rail lines directly into the FPR or branching to one and feeding the FPR?

Permanent grin
09-29-2011, 09:16 AM
Why two filters and two lines? Sounds more expensive that way?

2 filters each with -6an connections was better for flow that -10an line being reduced to -8an for the -8an connection on a single filter and then stepped back up to -10an line after.

It was more expensive but in our opinion, better delivery wise.


with one main feed, if you lose a pump you can still drive it home.

With our design, I CAN still drive it should 1 pump fail, due to the in line T piece in each line, connecting the 2 lines for pressure equalization purposes shortly after the filters.


You guys feeding the rail lines directly into the FPR or branching to one and feeding the FPR?

Yes, 1 line to each rail, then 1 line from each rail directly to the kinsler FPR which can accept 2 -6an feeds and has a single -8an return fitting.

André

J. Fast
09-29-2011, 09:28 AM
As it was explained to me, the FPR is not the place to collect the fuel lines. If one rail has an inflated or deflated pressure you'll probably never see it if the lines join right at the FPR. If you do it that way it would be wise to increase the return line diameter.

Hence, why you have larger return line?

J. Fast
09-29-2011, 09:30 AM
I suppose you could put a gauge on each rail but thats another $75 for no reason...

GTOJOE
09-29-2011, 09:34 AM
What is the max power that can safely be achieved on stock fuel lines? [upgraded lines from the filter and back to return line].

Permanent grin
09-29-2011, 09:34 AM
yes. kinsler make and supply very high quality fpr's, even to NASCAR. Mine was a mere $375 from them. I'm pretty sure if having 2 feed inputs on the FPR was that bad of an idea, they wouldn't offer it on their products.

André

MR2
09-29-2011, 09:14 PM
The plan is to go

1, Stock Tank
2, Dual pickup(modded stock hanger), one capped for the time being,
3, 8an feed goes through a 60micron filter
4, Then into 1 x Weldon D2015 (8an in 8an out) (Pump on Weldon 14000 regulator)
5, Through a 8an to 10an Y adapter (spare AN input capped)
6, 10AN Stainless Pipe Rear to front
6, join then a 10micron filter before the rails
7, straight into Ooohnoo fuel rails/regulator setup
8, 8an return line (stainless)

Space will be allowed for second D2015 + reg if required.

Pretty much covers everything?

IPD
09-30-2011, 12:41 PM
what the fuck are you talking about? I mentioned to get telfon lines hoses because of that.

I wish you would post about things you have a clue about, but then I guess you wouldn't post anything except the best xbox games.

wow. did someone wake up with their panties in a knot?

YOU were the one who said not to use braided stainless lines unless you wanted your car to smell like a gas station. the fact is, the outer covering doesn't matter worth a shit for that; only the inside line & coating does.

thanks for proving yourself to be a belligerent asshat yet again though. i think hellbringer might take offense to you encroaching on his territory.

Chris@Rvengeperformance
09-30-2011, 12:52 PM
wow. did someone wake up with their panties in a knot?

YOU were the one who said not to use braided stainless lines unless you wanted your car to smell like a gas station. the fact is, the outer covering doesn't matter worth a shit for that; only the inside line & coating does.

thanks for proving yourself to be a belligerent asshat yet again though. i think hellbringer might take offense to you encroaching on his territory.


No, I said "regular stainless lines", IE not teflon lined, but whatever you can do to twist what I said and "win"

I'm just sick of half of your posts. You read one post someone knowledgeable makes and then for years go around talking about it like you invented it and that it is the only way to go.

Have you even assembled a stainless steel or otherwise braided line with AN fittings?

AdamVR4
09-30-2011, 02:37 PM
Have you even assembled a stainless steel or otherwise braided line with AN fittings?

LOL... Going right for the balls, huh?

Chris@Rvengeperformance
09-30-2011, 02:54 PM
LOL... Going right for the balls, huh?

well I'm just getting tired of him acting like he knows more than anyone because he is a better "internet mechanic" than anyone else. I didn't start anything either, he took a unprovoked stab at me because he can't read what I said.

niterydr
09-30-2011, 02:56 PM
What I did and worked well:

Twin Walbro's angled out from each other on the stock hanger
Twin bulkhead fittings AN-06
AN-06 SS line for 1' off each pump to a Y
Y to 1/2" aluminum line (bendable and cheap) just needed adapter to AN (Fairly certain this won't work with E85 unless you have the line anodized)
1/2" Line to front of vehicle to fuel filter
Fuel filter to Y AN06 line
Y to each fuel rail AN06 line
Each fuel rail to fuel pressure regulator AN06 line
Fuel pressure regulator to stock return

Worked great. Twin walbro's and 6 880cc injectors @50psi base fuel pressure tapped out about the same time

IPD
09-30-2011, 10:23 PM
No, I said "regular stainless lines", IE not teflon lined, but whatever you can do to twist what I said and "win"

I'm just sick of half of your posts. You read one post someone knowledgeable makes and then for years go around talking about it like you invented it and that it is the only way to go.

Have you even assembled a stainless steel or otherwise braided line with AN fittings?

have you ever not been a total douchebag, mr. "i'm not even a 3sgto supporter"?

you NEVER specified what "normal stainless lines" meant. the wording of your post made it CLEARLY sound like nylon > stainless, and that stainless would make your car reek of gasoline.

maybe eloquence is not your forte. i simply stated a correction to your very poorly worded post.

/hijack. please return to your normal asshattery.

J. Fast
10-01-2011, 01:25 AM
What I did and worked well:

Twin Walbro's angled out from each other on the stock hanger
Twin bulkhead fittings AN-06
AN-06 SS line for 1' off each pump to a Y
Y to 1/2" aluminum line (bendable and cheap) just needed adapter to AN (Fairly certain this won't work with E85 unless you have the line anodized)
1/2" Line to front of vehicle to fuel filter
Fuel filter to Y AN06 line
Y to each fuel rail AN06 line
Each fuel rail to fuel pressure regulator AN06 line
Fuel pressure regulator to stock return

Worked great. Twin walbro's and 6 880cc injectors @50psi base fuel pressure tapped out about the same time
That's pretty much how mine is running except I ran braided for everything and when I exit the rails I consolidate into a "Y" and then feed the FPR. I thought about running solids but that was a huge bitch when I tested it. I had too many little bends and little curvy kinks in it. I could never get the line straight and get it to look like the brake lines. The line looked wavy, basically like ass, look good so I nixed that idea.

I figured I'd have to remove way too much shit to make it look right and I didn't have the time to go that route. It would've been cool for sure though. Did you just buy a 15 foot spool and go for it in place or did you use a bender and flatten it out first?

niterydr
10-01-2011, 02:40 AM
15' or 20' spool and pushed/bent into place as I went, moved from back to front, even managed to get the stock fuel line guards back up, then painted the line black so the local street racers didn't see whats up.

Of course those were the days I had my nitrous solenoids mounted under the car by the steering rack as well and ran the AN line for the nitrous INSIDE a vacuum line to the upper intercooler pipe, looked like a map sensor hook-up :)

mb7050
10-01-2011, 07:46 AM
now I know why my garage smells like gas station

Chris@Rvengeperformance
10-01-2011, 12:29 PM
have you ever not been a total douchebag, mr. "i'm not even a 3sgto supporter"?

you NEVER specified what "normal stainless lines" meant. the wording of your post made it CLEARLY sound like nylon > stainless, and that stainless would make your car reek of gasoline.

maybe eloquence is not your forte. i simply stated a correction to your very poorly worded post.

/hijack. please return to your normal asshattery.

Sorry my paypal subscription didn't auto renew. I'll fix that today.

As for your other nonsense. If you had every actually worked with an style hose instead if reading about it maybe you would've understood what I mentioned.


Sent from my DROIDX using Tapatalk

Checkered vr4
10-03-2011, 05:25 PM
I really like the gt pro magnum fuel system dynamic racing sells.

SnakeSkinner
10-03-2011, 08:00 PM
so the guy with dr1400's is only running -6AN. kinda proves my point about -10AN being WAY overkill.


People WAY over do fuel line size, to give you a idea the ID of the fuel line coming out of the stock fuel filter on my viper is 0.197" (Smaller then 1/5 of a inch), and my Viper puts 873 hp to the wheels!

The ID if -6 fuel line is ~0.450" of a inch!

Now that being said, it's better to be too big then too small.

GTOJOE
10-03-2011, 08:39 PM
People WAY over do fuel line size, to give you a idea the ID of the fuel line coming out of the stock fuel filter on my viper is 0.197" (Smaller then 1/5 of a inch), and my Viper puts 873 hp to the wheels!

The ID if -6 fuel line is ~0.450" of a inch!

Now that being said, it's better to be too big then too small.

Good info. How big are our stock lines and how much can they handle? I have everything required to upgrade all the lines in the engine bay but have not yet looked at supply lines.

[will be running an Aeromotive Stealth 340lph pump and Fuelab 515 FPR etc]

MR2
10-03-2011, 11:31 PM
People WAY over do fuel line size, to give you a idea the ID of the fuel line coming out of the stock fuel filter on my viper is 0.197" (Smaller then 1/5 of a inch), and my Viper puts 873 hp to the wheels!

The ID if -6 fuel line is ~0.450" of a inch!

Now that being said, it's better to be too big then too small.

That's what she said.


SOMEONE HAD TO SAY IT ORRITE.

J. Fast
10-03-2011, 11:46 PM
so a big inside diameter... is good, or is it bad? :lo5l:

MR2
10-05-2011, 07:19 AM
Oh what's that?

http://3000gt.com.au/car/Fuel/DSC09996.JPG
http://3000gt.com.au/car/Fuel/DSC09995.JPG
http://3000gt.com.au/car/Fuel/DSC09993.JPG

Earls said best way to go is Aluminium line :) so I have 3m of 5/8(AN 10) and 3m of 1/2 (AN 8)

GTOJOE
10-05-2011, 09:32 AM
overkill much?

BigTyla
10-05-2011, 12:17 PM
Goodness, -8 AN? Why?!?!

Aluminum is an interesting choice. I wonder how easy it will be to route since you have to bend the line without kinking it. How much did you save with aluminum compared to nylon braided?

Tigchamp
10-05-2011, 06:08 PM
I run intank Aeromotive 340lph, -10 from the tank to a -10 Fuel lab filter, -10 to uprated (340lph) Bosch 044 inline pump, -8 to Y peice, 2 -6 to 3SX fuel rails, 2 -6 to y peice, 1 -6 to Aeromotive FPR, & standard feed line as return.
Jeff:rolleyes3:

MR2
10-06-2011, 12:18 AM
not sure on the savings, I ended up with a 6+ meter roll of the 5/8 and 3m of the 1/2 everything + fittings was $99 AUD

not sure on how much for braided, I did have Ooohnoo buy me some but now it won't be needed (I prefer the alu)

overkill is nice...it's pretty much a case of "well this part will never be an issue again"

KeithMac
10-07-2011, 04:10 PM
I used AN6 Stainless braided Teflon lines for my setup, running Methanol blends now and any fumes are bad news.. 1 AN6 line is a massive upgrade over the stockers.

VR-4ever
10-14-2011, 06:41 PM
Mike, come up here during the day on a weekday, we'll go to Hampton Rubber (http://hamptonrubber.com/ProductsServices.asp) and they'll have what you need.

OBXBoost
10-21-2011, 08:40 AM
OK... with all of this being said....

Any recommendations on a fuel filter?

MR2
10-21-2011, 06:23 PM
well, my design has 3 x filters;

1, A pair of 75 micron pickups,
2, A Performance fuel PF-9110 10 micron with Stainless element pre-pump
3, A fuel lab 82833 (extra long) 6 micron glass filter just before the Y splitter that feeds the rails

Greg E
10-22-2011, 12:06 AM
For a second I thought this thread was going to be a debate about wether or not to eliminate the fuel lines. :p

OBXBoost
10-22-2011, 11:59 PM
So nice to know Greg. BTW, the cop was for me.