PDA

View Full Version : Engine's Out! Winter build has started



Pages : [1] 2

Chris@Rvengeperformance
09-24-2011, 10:56 PM
Well I decided to do a lot more this year than I planned. Engine is getting:

Forged Crank
Probably Bore/Hone
Ported and Rebuilt Heads
DR750s
Bigger meth kit
Jackhammer timing Gears

Depending on the condition of the stock pistons and block I will either just re-ring or go forged with forged rods.

Engine pull was actually pretty easy. I had a good friend helping and we started at about 11:30 and had the engine on the ground by 7:30. That includes running around town for an hour picking up some supplies and working in our extremely cramped garage. Plus we eat some lunch.

It is really so easy that I'm really glad I just tore into it and did it. This was actually the most fun I ever had working on the car.

Here are a few pics (I'm in the dark green shirt):

http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_18-12-28_349mb0O_K4M4.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-17-49_253QMQc_9EU6.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-21-24_568zvlU_8FvQ.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-23-44_2669vdO_871B.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-23-53_917G182_1oHd.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-26-43_535yLUC_W8fY.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-26-16_97FFyG_15j1.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-30-23_199xl8c_z27m.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-38-32_336Le1i_3POE.jpg
http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-24_19-38-40_385Fx87_YySa.jpg

JasonY
09-24-2011, 11:03 PM
You're gonna looooooooove the 750's!

Jason

Chris@Rvengeperformance
09-24-2011, 11:13 PM
You're gonna looooooooove the 750's!

Jason

hope so. I was debating on a t3/t4 setup from matt or a IPS 16G kit, but I just don't think I would like the lag.

I figure if I'm going to do all this crap I may as well get the best turbo setup I can and be done with it.

JasonY
09-24-2011, 11:27 PM
You'll enjoy them, best turbo setup ive ever driven to date. Now that Todd's car is working 100% its just silly how quick it is considering they are a TD04 turbo.

Did a 40-110 pull and it couldnt have been over 5 seconds. Very very fast car.

Jason

mb3000
09-25-2011, 12:42 AM
Subscribed!

IPD
09-25-2011, 12:42 AM
subscribed, and i agree with jason. for stock displacement, 750's are the king.

J. Fast
09-25-2011, 01:20 AM
I thought the motor was good and the leakdown and compression numbers were good? You're going to crack it open?

Chris@Rvengeperformance
09-25-2011, 01:32 AM
yeah it was, but it needs a forged crank anyway. The last thing I want to do is put a bunch of crap through my new turbos.

It also needs a trans overhaul. So, with those two facts in mind it doesn't really make sense to not go through the whole thing. If the pistons, rings, and cylinder walls are perfect I'll just swap the crank and be on my way.

Shouldn't be any serious balance issues changing the crank should there?

IPD
09-25-2011, 01:40 AM
you already have a crank? if not...milt's selling one of his babies. same treatment he runs & i'm using on my new build...

Chris@Rvengeperformance
09-25-2011, 01:41 AM
yeah I have a std std good forged crank.

On top of the above I want to install my cam gears, so it was getting silly to not just pull the motor.

Chris@Rvengeperformance
09-25-2011, 06:17 PM
hey Jason, do you think I should just get some 660s now or break the engine in on my 550s that I have a fairly decent tune for?

If I switch to 660s I'll probably just change the base tune on the mafT and it should be good enough to idle and low load around stoic for breakin.

JasonY
09-25-2011, 06:36 PM
I would break the engine in on the 550's. I normally put the stockers/stock ecu back in for engine break in, but since you are starting with a good tune, you should be fine.

Jason

lawdogg
09-25-2011, 07:38 PM
Looks great man! Nothing beats looking at that engine coming up and out!! Well, maybe seeing it go back in when the time comes ... lol!

Chris@Rvengeperformance
09-25-2011, 07:52 PM
lol

what's the trick to getting the trans off the block when the whole thing is sitting on the ground or dangling by the cherry picker?

I'm wishing I would have just dropped the trans while the engine was still in. I'm sure my clutch disk is bent to hell by now.

Anyone know if an RPS 6 puck disk will work with my ACT Plate? Does a full face disk stand a chance?

JasonY
09-25-2011, 08:10 PM
ahh, yours is good and stuck, i lowered the trans onto blocking to support the trans high enough to level out the engine/trans combo and just pried it straight off on Todds car when his input shaft was pretty much stuck in the clutch disk.

Full face clutch is fine, just dont track it much and if you do, give it lots of time to cool off between runs and dont ride it much out of the hole. Not sure on on the clutch combo.

Jason

Chris@Rvengeperformance
09-25-2011, 08:16 PM
yeah its good and stuck

If I just toss another mitsu disk in there will I still need to resurface the flywheel? I put this clutch in maybe only 5K miles ago, but it seems dumb to not put a new disk in while its apart. It would be the exact same clutch disk, just new.

JasonY
09-25-2011, 08:22 PM
I would just check the step height, if its in spec, i dont think it would need to be resurfaced?

Jason

Chris@Rvengeperformance
09-25-2011, 08:37 PM
yeah it was resurfaced when I put it on last year, if it doesn't have any cracks or hot spots I'm gonna just run it.

Picked up some ratchet straps to try to level the engine, it keeps wanting to lean a ton towards the trans side and is binding up the clutch.

lawdogg
09-25-2011, 08:48 PM
Use the lawn chair trick. Sit in a lawn chair and have someone lower the tranny onto your lap, with the engine & trans on the hoist. Now, get them to pull the engine away from you, and you hold onto the trans. Compliments of Iowa crew. That's how Jon and I did mine a few weeks ago.

Chris@Rvengeperformance
09-25-2011, 09:32 PM
that is a great idea. If you saw my garage right now you'd see why I can't try it though :)

There is like inches to work everywhere. I gotta get this engine on the stand and get the cherry picker out of here so I have some room to break the engine down.

I got the trans off. I was leaving 2 headless bolts in the bellhousing so it would slide off and not put weight on the clutch, but that was just making it really hard to get apart. I took those out and hooked a ratchet strap to the water neck to keep the engine from tilting down so far and we wiggled it apart no problem.

The flywheel looks great. You can still see the machining marks, so that is going to stay. The pressure plate is perfect too. No signs of hot spots, this clutch hasn't been overheated. The disk is still pretty good, but I'll get a new one since they are only like $60.00.

Very happy with the condition of the clutch components.

I see lots of spots that were leaking on this poor guy, even the rear main was damp and I replaced that a couple years ago. This thing is such a mess, I don't know how I'm gonna get it clean with the car in the garage with me. I'm tempted to put the axles back in the car and roll it outside, but I'd have to put the hood back on or get a car cover. I also am going to paint the under hood black and cleanup the years of aftermarket wiring and vacuum hoses I have everywhere, so it really needs to stay inside :( I wish my garage was about 10 foot longer. Very hard to work in it.

J. Fast
09-26-2011, 10:36 AM
You don't need the axles in to roll it out. Just put the tires back on, it will roll just fine.

Chris@Rvengeperformance
09-26-2011, 10:51 AM
You don't need the axles in to roll it out. Just put the tires back on, it will roll just fine.

The wheel bearings can be damaged doing this with out the axle nut holding them together


Sent from my DROIDX using Tapatalk

Chris@Rvengeperformance
09-26-2011, 01:21 PM
turbo choice is finalized, half of my 750s are paid for.

FeaRpb
09-26-2011, 02:15 PM
Congrats, This build sounds fun.

This kind of tempts me to make a winter build thread also.

Hope yours comes out good. Can't wait to see it finished.

Chris@Rvengeperformance
09-26-2011, 02:19 PM
I'm doing a lot, but it is all really proven simple stuff. I'm not forging any new territory, so it should work out fine.

Anxious to get the heads off this thing and see what the pistons and bores look like.

NOMIEZVR4
09-26-2011, 05:29 PM
Good Luck..keep us posted with pictures..I love reading build threads.

Chris@Rvengeperformance
09-26-2011, 07:02 PM
will do, going to try to get it up on the stand tonight, I had to pickup some bolts the right length. I sure got hosed, haha. It was like $14.00 for 4 bolts and some washers the right size.

green-lantern
09-26-2011, 07:49 PM
Oh damn, not sure how I missed this. Looking forward to following the thread (take lot's of pics :D)

Your engine had a lot of miles right? I think I remember you talking about maybe gong with a 4 bolt block? That might have been Aaron. Anyway I'm envious about the DR750's.

Drweldin
09-26-2011, 08:00 PM
I just did all of this in 2009 (oops)..minus 750's of course. Wish I would have documented it....don't care to do it again for a while.
In for more pics as well...

CoopKill
09-26-2011, 08:07 PM
In to follow what I am doing in a few months... if my ram will stay together long enough to save for my build, again.

X2 on the pics and stories of the heartache n happiness...


Sent from my DROID2 GLOBAL using Tapatalk

Roybatty
09-26-2011, 08:37 PM
will do, going to try to get it up on the stand tonight, I had to pickup some bolts the right length. I sure got hosed, haha. It was like $14.00 for 4 bolts and some washers the right size.

Surprising how expensive some of the metric bolts r. I usually go to Sears hardware & went w/ grade 8 sae, which has much better prices.

That is a tight looking garage. @ the rate u going, may b done sooner than planned.

connected via tapatalk

Chris@Rvengeperformance
09-26-2011, 10:19 PM
Oh damn, not sure how I missed this. Looking forward to following the thread (take lot's of pics :D)

Your engine had a lot of miles right? I think I remember you talking about maybe gong with a 4 bolt block? That might have been Aaron. Anyway I'm envious about the DR750's.

yeah it had 161,000 miles. Main thing was I know that the DR750s are not going to be kind to my old cast crank, so I got a forged one. I hope I don't need any machine work done, this will get done really fast if I don't.

Sticking with the 2 bolt though.

Chris@Rvengeperformance
09-27-2011, 12:13 AM
I got it on the stand earlier, gotta drain the coolant out of the block, clean up the garage, and bag some bolts before I tear it down further. I'm also going to break down the cherry picker and pack it up to save some space, won't need it for a while.

Had to drill out one of the engine stands bolts to make it fit right. no big deal though.

seems to be a nice stand, was $70 shipped from amazon and it is a torin. Amazon.com: Torin T24541 1000 lb. Engine Stand: Automotive (http://www.amazon.com/Torin-T24541-1000-Engine-Stand/dp/B000CODPEC/ref=sr_1_2?ie=UTF8&qid=1317093082&sr=8-2)

I didn't trust the 750lb models, I wanted some overhead.

http://www.chrisbehnken.com/Images/photos/EnginePull/2011-09-26_20-05-27_733zdh7_hVlI.jpg

the 19ts are in perfect shape. pretty much everything I have seen so far is in great condition, hope that trend continues.

shmoo
09-27-2011, 06:16 AM
nice

i'm about to do this. but i'm trying to do it for as cheap as possible.

you wouldn't happen to have an ecu lying around, would you?

_isiah

IPD
09-27-2011, 06:16 AM
nice

i'm about to do this. but i'm trying to do it for as cheap as possible.

you wouldn't happen to have an ecu lying around, would you?

_isiah

should have stuck with the 1g skirts. now it just looks off....

Ninja Performance
09-27-2011, 10:14 AM
DR 750s, nice choice for sure!

-Chris

green-lantern
09-27-2011, 10:40 AM
yeah it had 161,000 miles. Main thing was I know that the DR750s are not going to be kind to my old cast crank, so I got a forged one. I hope I don't need any machine work done, this will get done really fast if I don't.

Sticking with the 2 bolt though.

Are you going to have a machine shop go over everything? If it’s too lose and they want to grind and use oversize bearings don’t let them because you can probably use select fit mitsu bearings. My shop wanted to grind my crank but I was able to use the select fit and it came out perfect. The guy acted mad when I told him no don’t grind it I can get bearings that fit, he didn’t believe me. lol He changed his damn tune later when he had to eat his words. Other than that he did a great job.

Chris@Rvengeperformance
09-27-2011, 11:43 AM
Are you going to have a machine shop go over everything? If it’s too lose and they want to grind and use oversize bearings don’t let them because you can probably use select fit mitsu bearings. My shop wanted to grind my crank but I was able to use the select fit and it came out perfect. The guy acted mad when I told him no don’t grind it I can get bearings that fit, he didn’t believe me. lol He changed his damn tune later when he had to eat his words. Other than that he did a great job.

I don't know yet, it really depends on the condition of the bores. If I can get away with a light hone and just new rings I'll probably not need machine work. I have some bore gauge tools to inspect the bores, I'm going to blueprint them the best I can and see if they are out of round.

The crank I have now is already micro-polished from a machine shop and it has already been checked out to be std. std. The only thing I'm concerned about are the rods. I'm sure they could use resizing, but if I am going to go to that trouble I'm going with the spool/3sx rods.

I'm going to look at the rod bearings and if they are worn evenly I'm going to put the new crank in and plastigauge. If I get between .0015 and .0025 I'm not going to get much more excited about it. It isn't like I'm pushing the limit of anything and I'd rather take my chances on the stock machine work than get it screwed up. Clevites came out to .002 last time when I swapped them out, so unless this crank is a lot smaller I should be okay.

I'm definitely not going to grind the crank. This engine has never spun a bearing, had good compression, and good leak down so I really don't think its going to need too much work.

Chris@Rvengeperformance
09-27-2011, 11:44 AM
DR 750s, nice choice for sure!

-Chris

thanks, I figure if it is worth doing, its worth doing right.

Chris@Rvengeperformance
09-27-2011, 11:45 AM
should have stuck with the 1g skirts. now it just looks off....

nah, your eyes are broken, how about you don't worry about his car.

Chris@Rvengeperformance
09-27-2011, 11:49 AM
hey anyone know of a good intercooler core that I can swap my cxracing one for? I'm happy with the piping, but would like a spearco, ets, bell, treadstone, pte, etc type of intercooler. Should be pretty simple to find one. I think the core is 24" by 12" by 3" on this, with the overall width about 28". I don't want to go thicker, just more efficient. I could go a little wider, but the pipes would have to be cut and re-flared.

There may be enough give to go 26" wide on the core without changing the pipes. I have no oil cooler on the drive side, so I have a lot of room to move the pipes around.

Chris@Rvengeperformance
09-27-2011, 12:19 PM
hey can anyone recommend a good ring filer? what is a decent stock replacement ring pack?

you are supposed to use a 300 grit hone for stock style rings, correct?

I'm looking at a simple tool like this since i'll only need it once:

http://www.summitracing.com/parts/PRO-66785/

Ninja Performance
09-27-2011, 09:43 PM
I don't know yet, it really depends on the condition of the bores. If I can get away with a light hone and just new rings I'll probably not need machine work. I have some bore gauge tools to inspect the bores, I'm going to blueprint them the best I can and see if they are out of round.

The crank I have now is already micro-polished from a machine shop and it has already been checked out to be std. std. The only thing I'm concerned about are the rods. I'm sure they could use resizing, but if I am going to go to that trouble I'm going with the spool/3sx rods.

I'm going to look at the rod bearings and if they are worn evenly I'm going to put the new crank in and plastigauge. If I get between .0015 and .0025 I'm not going to get much more excited about it. It isn't like I'm pushing the limit of anything and I'd rather take my chances on the stock machine work than get it screwed up. Clevites came out to .002 last time when I swapped them out, so unless this crank is a lot smaller I should be okay.

I'm definitely not going to grind the crank. This engine has never spun a bearing, had good compression, and good leak down so I really don't think its going to need too much work.

I would shoot for 20 on the mains and rods. Resizing the rods is pretty cheap as are spool rods.

You may want to shore up the girdle with these, it is what was on my setup when I was 2 bolt.

ARP 6G72 91-92 TT 2 Bolt Main Studs (NP2boltmains) - Ninja Performance - Affordable Performance (http://www.ninjaperformance.com/product_info.php?cPath=344_399&products_id=2108)

-Chris

Chris@Rvengeperformance
09-27-2011, 11:40 PM
thanks for the info, do you sell the spool rods?

I got the rear turbo and manifold off. Laughably easy with the engine out. Anti-seize pays off. After I broke the nuts loose all the studs screwed out with my fingers. Everything is good so far. I got to inspect the damage to my rear stub shaft mounting bolt holes up close. I actually stripped one of these out and broke a corner off another a few years ago. The bottom one I was able to helicoil, but top one has basically been 3/4's of a bolt hold for a long time.

Probably going to drill it out and put in a timesert. There are a lot of good threads deep down. I can post some pics later. If nothing else I will have to weld the boss back up or use my backup block.

I'm probably going to break the whole thing down Saturday.

The rear coolant drain is frozen, should I heat it up or lust leave it alone?

TurboSinceBirth
09-28-2011, 02:32 AM
I made my own ring filer tool using some 3" grinding discs and scrap steel. You could either do that or buy one. You just want a straight/uniform file on the end which isn't too hard to achieve.

Chris@Rvengeperformance
09-28-2011, 11:23 PM
Here you guys can see the bolt boss I was talking about:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_767797IA_xdS8.JPG

haha valve cover gasket anyone?

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_76768T0w_t14R.JPG

bye bye 19t:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7679LJ04_j7Mg.JPG

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7680A603_33eW.JPG

bye bye shit stock manifold (trying to get in on gilbert's group buy for his badass header) No cracks in this one at least.

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_76815xQz_MIbv.JPG

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7683X812_8gNd.JPG

Only worked about an hour tonight, saving the head pull for my friend because he wants to see how it all goes together. He's new to working on cars and I'm trying to teach him some things.

I was able to get the front block drain open, so I'm going to leave the back one alone for now. I don't really want to twist it off.

Ninja Performance
09-29-2011, 09:11 AM
I made my own ring filer tool using some 3" grinding discs and scrap steel. You could either do that or buy one. You just want a straight/uniform file on the end which isn't too hard to achieve.

Nice cheap tool for something you could spend lots on. The nice grinders allow you to set the amount of the cut which is nice.

I usually just use a file.

-Chris

Ninja Performance
09-29-2011, 09:17 AM
thanks for the info, do you sell the spool rods?

I got the rear turbo and manifold off. Laughably easy with the engine out. Anti-seize pays off. After I broke the nuts loose all the studs screwed out with my fingers. Everything is good so far. I got to inspect the damage to my rear stub shaft mounting bolt holes up close. I actually stripped one of these out and broke a corner off another a few years ago. The bottom one I was able to helicoil, but top one has basically been 3/4's of a bolt hold for a long time.

Probably going to drill it out and put in a timesert. There are a lot of good threads deep down. I can post some pics later. If nothing else I will have to weld the boss back up or use my backup block.

I'm probably going to break the whole thing down Saturday.

The rear coolant drain is frozen, should I heat it up or lust leave it alone?

I don't carry them, but I think I have a set of the 3SX rods in a box somewhere. Was saving them in case I blew this engine....but other more important things have come up.

The rear drain shouldn't break, have never seen or heard of one snap. Although anything is possible. You could apply a little heat to the block and not the bolt to help. NOT TOO MUCH HEAT, I have seen these blocks crack with applying heat - BE CAREFUL. Once it's cracked it's junk. I have seen skilled welders unable to successfully weld it back up.

Worst case there is a little coolant in there which will come out through the top end when you tip the block on the stand.

-Chris

Chris@Rvengeperformance
09-29-2011, 11:43 PM
well I got the front head off:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7698Pmhs_4X6O.JPG

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_76995B6d_m40z.JPG

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7700DIpa_b79v.JPG

http://www.chrisbehnken.com/Images/photos/EngineTearDown/100_7701Dmo0_LesP.JPG

The cylinders look pretty good to me. I do not think it needs a bore, only a light hone and new rings. You can see almost all of the original cross hatch.

The head shows some evidence of oil leakage in the 2 cylinders I've had issues with the plugs in. The #1 cylinder has a lot of carbon and showed the most valve stem seal leakage. The head gasket showed no signs of leakage and there is no sign of detonation, even though this engine has seen a lot of knock counts. Makes me wonder...

I'm going to break the rest of the motor down Sat. If the rest of it looks this good I'm going to clean the shit out of it, hone it and re-ring it here in the garage. Then if the new crank specs in good with my mains and rods I'm going to put it back together.

Hey Chris, how do you know when you are done honing? How many passes does it take. I remember you used to do this a bunch way back in the day.

Ninja Performance
09-30-2011, 09:27 AM
Get a ball hone (if you don't already have one). It is the easiest to use deglazer/finisher and you literally can't mess up the bore with it. Spray WD-40 in the bore after you clean it. Ball hone attaches to a drill and as you spin it in the drill you push and pull it in and out of the bore. It won't take but a handful of passes to get a proper finish.

http://www.rockymountainatvmc.com/images/orprod/400/f/fle_10_cyl_bal_hon_all.jpg

-Chris

Chris@Rvengeperformance
09-30-2011, 10:53 AM
Get a ball hone (if you don't already have one). It is the easiest to use deglazer/finisher and you literally can't mess up the bore with it. Spray WD-40 in the bore after you clean it. Ball hone attaches to a drill and as you spin it in the drill you push and pull it in and out of the bore. It won't take but a handful of passes to get a proper finish.

http://www.rockymountainatvmc.com/images/orprod/400/f/fle_10_cyl_bal_hon_all.jpg

-Chris

thanks a bunch chris. This looks like the correct size and grit right? Going with sealed power rings.

Amazon.com: Brush Research FLEX-HONE Cylinder Hone, GBD Series, Silicon Carbide Abrasive, 3-3/4" (95 mm) Diameter, 240 Grit Size: Industrial & Scientific (http://www.amazon.com/Research-FLEX-HONE-Cylinder-Abrasive-Diameter/dp/B002XUL1LC/ref=sr_1_8?s=industrial&ie=UTF8&qid=1317390659&sr=1-8)

Ninja Performance
09-30-2011, 10:57 AM
That will do it.

-Chris

Chris@Rvengeperformance
09-30-2011, 11:41 AM
awesome

AdamVR4
09-30-2011, 11:42 AM
So did you actually have low compression?

Chris@Rvengeperformance
09-30-2011, 11:46 AM
So did you actually have low compression?

no it was actually great. 150-155 PSI on all and 10% cold leakdown.

I'm a little on the fence about touching it, but you can see some skirt wear on the bore in the #5 cylinder. I'd hate to put this guy all together and have to do it all again in a couple years.

What do you think? I'd really like to pull the pistons and check for evidence of blowby. I always had quite a bit of oil in my rear intake tube from the breather. It had to be coming from somewhere.

I can re-ring this for $100 worth of rings and a $50 tool, but I am leery of touching something that works. I'd love to just take the whole damn thing to Ray or Von's guy, but that seems wasteful since everything is basically in good shape now. I would have to go fully forged to get myself to do that and that seems wasteful too.


Did you guys look at the knock sensor? Doesn't it look like its leaking? Maybe that's why this engine was always noisy. It would have a nice solid tune on it, then randomly you could be driving around town and gas on it and see counts in the 20s with a good afr and conservative timing.

Ninja Performance
09-30-2011, 12:09 PM
It's out. I would deglaze/hone it and re ring it. If it were me.

-Chris

Chris@Rvengeperformance
09-30-2011, 12:12 PM
It's out. I would deglaze/hone it and re ring it. If it were me.

-Chris

thanks, that's my thinking. I'm putting a crank in it anyway, might as well have it all perfect.

Do you think that is a lot of skirt wear? I really haven't had to many blocks apart and when I did they were all 350s that seem to lose their hone pattern after a couple years of hard farm use.

AdamVR4
09-30-2011, 12:23 PM
Would honing it even remove the skirt wear marks? If not, I think the answer is clear.

Get yourself some krank vents or a catch can or something to clean up your intake system.

Replace the knock sensor if it's original. No reason to mess around with that. I replaced my knock sensor when I took the heads off and have no regrets at all.

If you peg your DR750's long enough, you're going to cause a conrod fatigue failure. Would you rather do a full build now or do a full build in a couple years when this engine gives up the ghost? If the answer is the latter (and I wouldn't blame you), you should at least put filters in your oil feed lines. I can't imagine strapping such expensive turbos onto an engine without trying to do something to prevent them from being taken out do to a spun bearing (not much you can do if you frag a piston) ...

So after talking myself in circles, if it were my car, I'd try to protect the turbos with forged pistons at the very least, and at that point, you might as well get forged rods ...

This is why I like my cheap turbos.

Chris@Rvengeperformance
09-30-2011, 12:46 PM
Would honing it even remove the skirt wear marks? If not, I think the answer is clear.

Get yourself some krank vents or a catch can or something to clean up your intake system.

Replace the knock sensor if it's original. No reason to mess around with that. I replaced my knock sensor when I took the heads off and have no regrets at all.

If you peg your DR750's long enough, you're going to cause a conrod fatigue failure. Would you rather do a full build now or do a full build in a couple years when this engine gives up the ghost? If the answer is the latter (and I wouldn't blame you), you should at least put filters in your oil feed lines. I can't imagine strapping such expensive turbos onto an engine without trying to do something to prevent them from being taken out do to a spun bearing (not much you can do if you frag a piston) ...

So after talking myself in circles, if it were my car, I'd try to protect the turbos with forged pistons at the very least, and at that point, you might as well get forged rods ...

This is why I like my cheap turbos.

We are basically thinking exactly the same. If I hadn't had a cast crank in this engine I probably would've just pulled the heads and not worry about bottom end. I think the hone will clear up the skirt marks. In real life you can see the hone marks through the darker sport, so it really isn't very deep at all.

I do have a catch can and it did help, but it is really a band-aid for something.

I'm not really planning on pegging the turbos at all. I would only try to run 22-23 PSI or so at the most. That should translate to somewhere around 525AWHP AFAIK. I think the engine should live a long time at this level, especially as little as I really drive it. I've always wanted a strong track setup that is exactly as I drive it day to day. I'm just not a race gas kind of guy. If anything I'd go with e85.

I'd really rather build it later just because if I am going to get any engine work its going to be from ray and at that point I may as well buy one of the shortblocks he sometimes has for $2500-3000 complete and just sell mine as a running engine. I'm not going to drop $1500 worth of new rods and pistons and my crank off at just any shop and have them build it thinking it is some minivan engine or a ricer that isn't going to make any real power.

I've seen a lot of full builds blow up on the forums, which is why I'm keeping this basically and sticking with something that has never spun a bearing or given major problems at any time.

I was very close to getting an IPS TD05 kit or dr's dr800 setup, but it didn't really fit my goals. I just want something simple that is going to make another 100-150 AWHP and spool even faster than my 19Ts. There is no other setup at any price that I know of that can do that.

I hear what you are saying about the oil filters, but they are not free from issues either.

1. I asked matt and he basically said the warranty was only good with stock lines. If he wants to post and correct me on this that's ok, but that is what I understood from our pm's.
2. If the filters get clogged and you don't notice you kill the turbos too.
3. As long as you don't destroy any of the wheels the DR750s are not that expensive to rebuild. Yeah if a chunk of piston goes through them you are in for a huge bill, but I don't see what you can do about that. Even EVO IIIs are what $1100 if that happens?

I appreciate everyone's point of view, it is hard for there to be a "right" answer in this case.

It is the same thing with my transmission. It needs a new 2nd gear to shift nice. The problem is the bell housing has some damage. So, I picked up a good case and a good gear with slider, but then if I go that far why not just send the trans off and spend $1000-1500 on it. Then if I'm going to do that I may as well upgrade to a 25 spline shaft. Then I have to get a new 300m shaft and a new spool for my t-case. It really never ends. My billet housings are sitting on the shelf because I can't decide which way I'm going to go with the damn spline count.

good times though, not really worked up about it at all. I'm in no hurry to get it going again, but I want to be running in the spring to have time to shake it down for the track season.

AdamVR4
09-30-2011, 12:58 PM
That cast crank would really concern me at 500+ AWHP. Did IPO's testing at 3SX put your mind at ease there?

525 AWHP at ~22-24 psi on pump gas should be totally doable; at least it's doable with my DR headers + E3's.

I'm with you on Ray/Scott engines. I still go back and forth on my long-term goals, but if I ever plan to push beyond 600 AWHP, I'm getting a 4340 crank and letting Ray do the assembly.

What sort of bell housing damage are we talking about? Unless your trans has been eating synchros on a regular basis, I'd stick with the original bell housing and swap in a new synchro. 1st and 2nd gear are so easy I used to pull the trans, make the synchro swap and have the car running again the same day.

Man, if you've got a 300m 18 spline output shaft, why are you beating yourself up about spline count? Stick with the 18 spline and install your billet t-case housing!

Chris@Rvengeperformance
09-30-2011, 01:06 PM
That cast crank would really concern me at 500+ AWHP. Did IPO's testing at 3SX put your mind at ease there?

525 AWHP at ~22-24 psi on pump gas should be totally doable; at least it's doable with my DR headers + E3's.

I'm with you on Ray/Scott engines. I still go back and forth on my long-term goals, but if I ever plan to push beyond 600 AWHP, I'm getting a 4340 crank and letting Ray do the assembly.

What sort of bell housing damage are we talking about? Unless your trans has been eating synchros on a regular basis, I'd stick with the original bell housing and swap in a new synchro. 1st and 2nd gear are so easy I used to pull the trans, make the synchro swap and have the car running again the same day.

Man, if you've got a 300m 18 spline output shaft, why are you beating yourself up about spline count? Stick with the 18 spline and install your billet t-case housing!


I have a forged crank ready to go in. Not going to try to make this much power on the cast one.

There are a couple of bolt holes that had the ends popped out from too much RTV when this thing was rebuilt in the past. It's holding up, but not without jb-weld :) One of the long bolts that goes from the end case through the mid and into the bellhousing didn't torque up very well last time when I swapped out my output shaft.

I think I'm going to also put a new third in. I have the new syncro and sometimes I feel some resistance when shifting. I also have to do 5th because it grinds sometimes oddly enough. The other thing is that it is pretty loud in 2nd. Either the 2nd gear needle bearing is going out or the pre-load need to be reset on this thing.

The only reason I was thinking about a 25 spline setup is that if I can part this trans out I can just get a built unit from jackstransmissions and just pay the core charge. Total is $1600 then. If all the parts from my current trans sold I wouldn't be out a huge amount, but no one is buying anything so I'm going to have to rebuild what I got.

Its funny how "rare" getrag parts are, but when you try to sell them there are no takers.

AdamVR4
09-30-2011, 01:16 PM
I have a forged crank ready to go in. Not going to try to make this much power on the cast one.

There are a couple of bolt holes that had the ends popped out from too much RTV when this thing was rebuilt in the past. It's holding up, but not without jb-weld :) One of the long bolts that goes from the end case through the mid and into the bellhousing didn't torque up very well last time when I swapped out my output shaft.

I think I'm going to also put a new third in. I have the new syncro and sometimes I feel some resistance when shifting. I also have to do 5th because it grinds sometimes oddly enough. The other thing is that it is pretty loud in 2nd. Either the 2nd gear needle bearing is going out or the pre-load need to be reset on this thing.

The only reason I was thinking about a 25 spline setup is that if I can part this trans out I can just get a built unit from jackstransmissions and just pay the core charge. Total is $1600 then. If all the parts from my current trans sold I wouldn't be out a huge amount, but no one is buying anything so I'm going to have to rebuild what I got.

Its funny how "rare" getrag parts are, but when you try to sell them there are no takers.

I'd be very hesitant to throw a new crank into a rotating assembly without balancing. What's your plan there?

LOL! I blew out several of the blind threaded holes in my original trans. It was fine. Damn incompressible RTV also caused me to snap off an oil pan screw in my block. I just repaired that and took the time to clean the RTV out of all the holes.

Heh, I remember when I contemplated selling all my piggybacks in '09 to go EMS. No one wanted an emanage blue, scan master, MAF-T or over clocked 93 ECU. After wheeling and dealing for years, I was, uh, surprised.

*edit* What Getrag parts you selling? I'm always in the market.

Chris@Rvengeperformance
09-30-2011, 01:26 PM
I'd be very hesitant to throw a new crank into a rotating assembly without balancing. What's your plan there?

LOL! I blew out several of the blind threaded holes in my original trans. It was fine. Damn incompressible RTV also caused me to snap off an oil pan screw in my block. I just repaired that and took the time to clean the RTV out of all the holes.

Heh, I remember when I contemplated selling all my piggybacks in '09 to go EMS. No one wanted an emanage blue, scan master, MAF-T or over clocked 93 ECU. After wheeling and dealing for years, I was, uh, surprised.

*edit* What Getrag parts you selling? I'm always in the market.

Yeah I felt that way about the new crank too. Since they are all factory parts (although the 2G pistons weight may have been slightly different) and Mitsu offers only the forged crank nowadays anyway I'm going to cross my fingers and hope the balance is good enough. If I go to the trouble of balancing it I may as well get forged everything.

So, you think I should just fix up my bellhousing? That would be a lot easier. I may be able to helicoil that one bad hole.

here are the parts I may be selling:

http://www.3sgto.org/f62/gi-5-speed-getrag-transmission-partout-300m-output-shaft-6299.html

Chris@Rvengeperformance
10-01-2011, 04:47 PM
We'll we got the engine torn down completely. There is good news and bad news.

I replaced all the bearings 25k ago.

The rods today look really good. Almost no where.

The outside mains were also great.

The center mains were in rough shape. Both showed a lot if copper.

What's worse is the one center main is warped to Hell. It doesn't fit the crank or girdle at all.

The crank is lightly scratched on that one too. This thing was a pull away from spinning.

I guess the crank is bent from detonating over the years.

Pics later

Sent from my DROIDX using Tapatalk

Chris@Rvengeperformance
10-01-2011, 07:54 PM
Here are the mains:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-30-20_827oWq4_M20g.jpg

you can see the one bearing doesn't fit anymore, it is my custom oval bearings, going to be the next big thing:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-30-37_624D1Gc_Lv36.jpg

If you look closely you can really see how the bearing doesn't fit the crank. Look at the huge gap on the right side:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-32-21_37Ln7H_y6lk.jpg

you can see how the journal is scratched a bit:

http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-30-47_51150Rl_Ac35.jpg

I would not run this crank as is. I think it needs 10 thous cut off of it. Looks like this crank has turned over for the last time. Off the the scrap iron pile.

FYI the mains were in worst shape when I replaced them last time, but this is a ton of wear for 25,000 miles IMO.

Believe it or not this engine was as quiet as a mouse and had great oil pressure. I guess this may be another reason why this engine showed knock so easily. Probably really was making some bottom end noise under full load. I never heard anything though.

NOMIEZVR4
10-01-2011, 09:04 PM
Good to see the symptoms you were mentioning had a root cause. :)

Ninja Performance
10-01-2011, 09:37 PM
Believe it or not this engine was as quiet as a mouse and had great oil pressure. I guess this may be another reason why this engine showed knock so easily. Probably really was making some bottom end noise under full load. I never heard anything though.

Pounded bearings won't always produce low oil pressure. Especially if they cover oiling holes from proper flow. Good update!

-Chris

Chris@Rvengeperformance
10-01-2011, 10:22 PM
Thanks.

The rear bores were perfect. There was some big chunks of rtv over the oil pickup. I must have use to much last time. May have contributed to my main bearing problems.

Sent from my DROIDX using Tapatalk

Chris@Rvengeperformance
10-02-2011, 02:50 PM
well I just measured out my clutch and it measures out to new spec, so I think I'm going to run this disc until it cannot hold anymore. Seems silly to replace it now when I know if I get to making serious power I'm going to need a 6 puck disc.

Just placed a pretty good sized order with mitsu:

MD997669 GASKET KITENG OVERHAUL UPPER Mitsubishi 0 1 224.51
MF660064 GASKETA/T CASE Mitsubishi 0 8 1.15 (coolant o-rings)
MD620494 O-RINGFUEL REGULATOR Mitsubishi 0 1 6.16 (fuel inlet o-ring)
MD174793 TUBET/C OIL FEEDLH Mitsubishi 0 1 17.6 (turbo oil feed line)
MD161898 GASKETCLUTCH M/CYL Mitsubishi 0 5 0.98 (copper o-rings, only need 4)
MD161898 TUBET/C OIL FEEDRH Mitsubishi 0 1 16.54 (turbo oil feed line)
MD165464 PROTECTORT/C Mitsubishi 0 1 28.16 (front turbo heatshield)
MD165462 COVEREXHAUST MANIFOLD Mitsubishi 0 1 34.72 (front exhaust manifold heat shield)
MD050317 GASKETENG OIL PAN DRAI Mitsubishi 0 1 1.33
MD611222 BOLTSTARTER INR Mitsubishi 0 2 3.26 (starter bolts, mine are aftermarket and wrong)
MF244884 BOLTTIMING BELT TRAIN Mitsubishi 0 1 0.94 (timing tensioner bolt)
MD050316 O-RINGENG OIL FILLER Mitsubishi 0 1 0.97
MB698901 HOSE KITHEATER WATER Mitsubishi 0 1 23.99
MD147861 HOSET/C WATER FEEDRH Mitsubishi 0 1 2.78
MD081048 HOSETHROTTLE BODY WATE Mitsubishi 0 1 5.68
MD068186 HOSET/C WATER RETURNL Mitsubishi 0 1 2.16
MD168962 HOSET/C WATER FEEDLH Mitsubishi 0 1 3.13
MD168962 HOSETHROTTLE BODY WATE Mitsubishi 0 1 3.43
MD168561 HOSET/C WATER RETURNR Mitsubishi 0 1 2.78
MD159216 Knock Sensor
MD161167 Oil switch wiring harness

The rest of these are a couple bellhousing bolts and transfer case bolts I wanted to replace:

BOLTT/F CASE Mitsubishi 0 2 6.25
BOLTT/M CONNECTING Mitsubishi 0 3 1.67
BOLT-CLUTCH HOUSING MOUNTING Dodge 0 1 1.38
BOLTT/M CONNECTING Mitsubishi 0 2 2.1

TurboSinceBirth
10-02-2011, 09:31 PM
The motor on my 93 VR-4 when I bought it looked very similar to that only the center mains had spun. It had just done it though because the motor was quiet and oil pressure was great. As far as I can tell it must have hit a bunch of knock on the dyno when the last owner had it, the turbo blew, and he probably knew something else was damaged so he sold the car off to make it someone else's problem unfortunately.

AdamVR4
10-03-2011, 11:16 AM
http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-30-20_827oWq4_M20g.jpg

Are those inner mains down to copper or is the picture deceiving?

Chris@Rvengeperformance
10-03-2011, 01:01 PM
http://www.chrisbehnken.com/Images/photos/EngineTearDown/2011-10-01_14-30-20_827oWq4_M20g.jpg

Are those inner mains down to copper or is the picture deceiving?

yeah they are, see text

AdamVR4
10-03-2011, 01:07 PM
Ah, I missed posts 63 and 64.

Chris@Rvengeperformance
10-03-2011, 01:33 PM
good thing I took this thing apart, haha

AdamVR4
10-03-2011, 01:38 PM
Hmm.. Yeah. I've seen bearings that were worn below the copper layer (it's black below the copper, heh) that basically fell out of the girdle, but that one main looks like it had actually started being deformed by friction and was in the initial stages of spinning. Pretty amazing timing.

Roybatty
10-03-2011, 02:09 PM
I was gleaning that the rod bearings usually go first. I replaced them, while banging out oil pan, and left the mains alone for the 120k (actually did the oil pan twice cause the gasket doesn't work). Relatively stock and not pushing it, knock is under control.


Is it safe to say your mains condition is very specific to your car since you had similar issues 25k ago with all your mods and driving habits?

Chris@Rvengeperformance
10-03-2011, 02:50 PM
no, I think it is pretty common for our mains to be worn out when over 100K.

bboyalan
10-03-2011, 02:59 PM
Cool stuff Chris. Good luck! I am looking forward to the aftermath :)

AdamVR4
10-03-2011, 03:01 PM
no, I think it is pretty common for our mains to be worn out when over 100K.

Yeah... In doing 120K's, I've seen just as many heavily worn main bearings over the years as I have rod bearings. The original rod bearings in my car were fine, but main #2 was straight copper.

green-lantern
10-03-2011, 05:18 PM
Pretty amazing timing.


Indeed

Chris@Rvengeperformance
10-03-2011, 05:33 PM
does anyone know if 3sx has gotten it together with their oil pans? I want to get a new one and a new strainer. I know about the issue with the bolt holes, I don't really care about that. What I need to know is if this thing is going to leak like it has for others. If it is going to leak then I'll just clean up my old one.

Chris@Rvengeperformance
10-04-2011, 10:19 PM
well I got it tore down to the bare block tonight.

Only areas of concern were the #6 upper rod bearing was showing a bit of copper in the middle and the #1 rod was almost there. I'm guessing that the mains being pounded out were starving the rods a bit, but if anyone has any other ideas let me know.

I have a dial bore gauge set, so I'm going to check the rods for out of round tomorrow.

FYI there were no signs of blowby on the piston skirts. Practically zero wear on the skirts as well. No broken rings or lands, rings were all free and moved easily.

mb3000
10-05-2011, 01:08 AM
First 6G engine with non-broken ring leads?








Somebody call Steve!:w00t:

Chris@Rvengeperformance
10-12-2011, 10:23 PM
All my parts came in from mitsu today, I'm going to list out all the part numbers included in the top end gasket kit, because it wasn't clear when I ordered. I have duplicates of a few things.

My rings came in too, sealed power's from rockauto.

Timing belt came in as well. I replaced the water pump, oil pump, and all the timing components about 10K ago, so I am only replacing the belt now. I went oem on everything before, but actually used a parts dinosaur timing belt last time. It held up great and looks new, but it is silly to not replace it while its apart.

I went with a gates belt, because it was $50 and normally is a good brand. The oem timing belts are overpriced IMO and I've never seen a belt break that wasn't caused by another failure. The gates belt turns out to be made in the UK, so that is a lot better than mexico or taiwan or some crap. Seems to be of extremely excellent quality.


looks like I may not have to file these rings. I only checked the top ring on one cylinder, but is is .016" before honing. Honing shouldn't remove more than a thousandth, so if they all check out like this I am good to go.

Factory specs are:

012-.017" top
.017-.024" bottom

J. Fast
10-13-2011, 12:38 AM
Were you able to salvage the mains, rod bolts, and headstuds? You going to do your own portwork on the top end?

Chris@Rvengeperformance
10-13-2011, 10:45 AM
Were you able to salvage the mains, rod bolts, and headstuds? You going to do your own portwork on the top end?

sure, I'm re-using the stock fasteners where undamaged. I have a set of heads a guy is selling me that are already ported and rebuilt.

Ninja Performance
10-13-2011, 11:14 AM
does anyone know if 3sx has gotten it together with their oil pans? I want to get a new one and a new strainer. I know about the issue with the bolt holes, I don't really care about that. What I need to know is if this thing is going to leak like it has for others. If it is going to leak then I'll just clean up my old one.

Just get a new OEM oil pan. They weren't discontinued as some expected/reported. Otherwise, if I were you I would just clean up your old one.

-Chris

Ninja Performance
10-13-2011, 11:15 AM
sure, I'm re-using the stock fasteners where undamaged. I have a set of heads a guy is selling me that are already ported and rebuilt.

Get new OEM head bolts. No sense in re using them on a new build.

-Chris

Chris@Rvengeperformance
10-15-2011, 09:14 PM
honed the cylinders today. It worked great, have a nice pattern and it completely got rid of the dark spots. The cylinders look like new. It takes a little practice to get the drill speed the way you want it and keep the in down speed the way you want it as well. Both have to be in the ball park to get a good crosshatch. I kept wanting to go in and out of the cylinder too slow.

Luckily if you don't get the crosshatching you want, just give it another 2-3 passes and you can get it right.

I cleaned the hell out of the block. It takes a ton of cleaning to get the cylinders clean after honeing. I used a bottle brush and warm soapy water to scrub them and about a whole roll of paper towels to clean them. I kept cleaning until there was nothing on the towels. I'm sure some would say paper towels are bad because of lint, but I did a bunch of cleaning after that step anyway.

I cleaned the cylinders and whole block with soap and water. I then dried it off with compressed air. I also blew air into the oil pump feed in the front of the block to try to clean out the galleys. I think it worked because oil came out of the main journal feeds.

Then I hit everything with about 3 cans of brake clean and finally lightly oiled the cylinders, main caps, and deck surface to keep them from rusting. When I am ready for assembly I will have to re-clean the main caps and deck surface with brake clean to get rid of the oil.

The engine looks like it just came back from the machine shop, so I am pretty happy. Tomorrow we'll see how far I get, but I'm going to try to get the pistons cleaned up and installed in the block. I'l try to put up some pictures tomorrow.

green-lantern
10-15-2011, 10:23 PM
I would go OEM timing belt, I just don't trust aftermarket. I worry about the length or teeth being off. Just seems like something I don't want to skimp on.

Looking forward to seeing this come together. Take your time and be anal about everything. It can save you work down the road.

Oh and keep taking pics, love to see pics :)

Chris@Rvengeperformance
10-15-2011, 11:16 PM
not worried about the belt at all. It isn't like there is some Japanese Samurai warrior crafting it out of his basement in Japan somewhere just because it comes in a mitsu box. Gates is a respected brand and it says right on the belt made to oem specs.

I've been running a non oem belt since I got the car 5 years ago. The teeth have always lined up when I time them.

Ninja Performance
10-15-2011, 11:40 PM
I also would recommend OEM T belt, but gates should be fine. They have been around a while and make good products.

-Chris

Chris@Rvengeperformance
10-16-2011, 06:32 PM
Well I have some pics I'll put up later, but today I got the crank installed and spec'd out.

1,2 and 4 journal came out to exactly .002. The #3 journal is .0018.

Pretty happy with that, everything looks good so far. The crank was a standard standard crank that had been micro-polished at a machine shop for a member on here. The journals look perfect. The crank of course spins great with no pistons in right now.

FYI the markings on my block look like this:

I II III IIII

II II II
II II II

Chris@Rvengeperformance
10-17-2011, 12:22 AM
some pictures:

I recommend the pig mat stuff, great place to keep your parts and tools clean. Do not forgot to keep your tools clean, they can easily pickup a lot of dirt if you just throw them on the floor.

Cylinders came out nice and clean:

http://www.chrisbehnken.com/Images/photos/EngineBuild/125npd6_4Z54.JPG

It is not as rough as the flash makes it. The far side is more like it really is. You can see the angle of the crosshatching better too.

http://www.chrisbehnken.com/Images/photos/EngineBuild/1268459_KPfC.JPG

http://www.chrisbehnken.com/Images/photos/EngineBuild/127BLl9_onCb.JPG


Really nice forged crank:

http://www.chrisbehnken.com/Images/photos/EngineBuild/129a3S7_E2YJ.JPG


http://www.chrisbehnken.com/Images/photos/EngineBuild/131093I_7Mo0.JPG

http://www.chrisbehnken.com/Images/photos/EngineBuild/132oEA9_XXDO.JPG



after clearance checking stage, final assembly:

http://www.chrisbehnken.com/Images/photos/EngineBuild/1339cL3_L11L.JPG

gotta have the FSM around:

http://www.chrisbehnken.com/Images/photos/EngineBuild/13492m9_MjDC.JPG


back to sleep for now:

http://www.chrisbehnken.com/Images/photos/EngineBuild/136n0u2_H621.JPG

vroom4
10-17-2011, 12:35 AM
I needed something like that bag when I did my engine build. I just kept shrink wrapping it.

Chris@Rvengeperformance
10-17-2011, 12:37 AM
yeah they are only $10. Its worth it.

J. Fast
10-17-2011, 12:44 AM
That turned out really good! Damn, in some of those pics you can tell you're cramped for space. Coming along nicely!

J. Fast
10-17-2011, 12:48 AM
You wouldnt mind putting some skures in your crank to show the oil channels would you?

Chris@Rvengeperformance
10-17-2011, 01:17 AM
You wouldnt mind putting some skures in your crank to show the oil channels would you?

sure, but I'm not sure what you mean. The crank is nothing special. its from a 1994 Auto NA, so it hasn't been beat on. I gotta transfer the dowl pin over yet when I put the flywheel back on.

Chris@Rvengeperformance
10-17-2011, 01:18 AM
That turned out really good! Damn, in some of those pics you can tell you're cramped for space. Coming along nicely!

it is really tight, but there is just enough space. It doesn't really take a lot to build the engine.

Chris@Rvengeperformance
10-17-2011, 01:21 AM
btw word to the wise, be careful removing the main girdle. Knock it loose first and then pull it off. I had a little bit of up pressure while I was knocking it loose. It came loose in a jolt and I put a tiny knick in one of the mains. :( I went over it with some thousand grit until you couldn't feel it, but its a shame, the surface was perfect.

Chris@Rvengeperformance
10-18-2011, 12:30 AM
well I measured the gaps of all the rings. The top ring was 17 thou on 5 cylinders and 18 on 1. Just fine.

The 2nd rings were way to tight. some came out around 12 thousand. I shot for 20-21 thousands on all of them. 5 of them I got right, but the first one I screwed up and it came out to 25 thous. I guess I gotta order a new ring set for one cylinder :(

Ninja Performance
10-18-2011, 10:09 AM
I needed something like that bag when I did my engine build. I just kept shrink wrapping it.

Get a 55 gallon trash bag. They work like a charm.

-Chris

Ninja Performance
10-18-2011, 10:15 AM
well I measured the gaps of all the rings. The top ring was 17 thou on 5 cylinders and 18 on 1. Just fine.

The 2nd rings were way to tight. some came out around 12 thousand. I shot for 20-21 thousands on all of them. 5 of them I got right, but the first one I screwed up and it came out to 25 thous. I guess I gotta order a new ring set for one cylinder :(

Common practice, and I have done it for years, is to make that bottom ring on the large side. This way it allows some blow by. If it is too tight not enough blow by get by the ring and it ricochets (ring flutter) right into the top ring and can cause it to break. 25htou/.63mm isn't out of line. I have built them even larger, up to .75mm testing ring gaps on the race car and everything was great.

Think about that gap when the ring in compressed in the bore. AND most of it is covered up by the piston. Only a Smidgen is out in the free air making a gap.

I would not worry about it. It anything, cause I am anal, I would bring the others up closer to the large one to "even" then up. I surely wouldn't buy a ring pack to replace it.

-Chris

Chris@Rvengeperformance
10-18-2011, 10:50 AM
Common practice, and I have done it for years, is to make that bottom ring on the large side. This way it allows some blow by. If it is too tight not enough blow by get by the ring and it ricochets (ring flutter) right into the top ring and can cause it to break. 25htou/.63mm isn't out of line. I have built them even larger, up to .75mm testing ring gaps on the race car and everything was great.

Think about that gap when the ring in compressed in the bore. AND most of it is covered up by the piston. Only a Smidgen is out in the free air making a gap.

I would not worry about it. It anything, cause I am anal, I would bring the others up closer to the large one to "even" then up. I surely wouldn't buy a ring pack to replace it.

-Chris

Thanks Chris, I was hoping you'd say something like that.

I guess I'll bring the other gaps up to about 22 thousandths. I don't really want to run them all at 25 because I'd like this to burn little oil.

Do you think the top ring being 17-18 is good?

Ninja Performance
10-18-2011, 11:55 AM
Thanks Chris, I was hoping you'd say something like that.

I guess I'll bring the other gaps up to about 22 thousandths. I don't really want to run them all at 25 because I'd like this to burn little oil.

Do you think the top ring being 17-18 is good?

25 won't burn oil

17-18 is fine.

Also keep in mind the ring pack/pistons you are using and the bore size. The rings/piston set should have come with a paper stating .XX per bore size for the rings. Try to follow that also.

-Chris

Chris@Rvengeperformance
10-18-2011, 11:45 PM
yeah surprising enough this ring setup didn't contain any gap specs and barely any instructions. I guess since it is stock replacement they expect you to use stock specs or not gap them.

One piston and rod is installed:

http://www.chrisbehnken.com/Images/photos/EngineBuild/100_7744t02B_btjq.JPG

Rod clearance came out to .019. Really happy with that.

$7.99 ring compressor from sears worked fine. Engine still turns pretty easily by pushing on a counter weight.

just like new:

http://www.chrisbehnken.com/Images/photos/EngineBuild/100_774553B5_Msm3.JPG

I followed the manual for where to put the rings gaps as bet as I could. Going to be pretty nervous starting this thing :) Next time I'm just going to pay ray to build something for me. Too many variables.

Primus101
10-19-2011, 07:12 PM
.019" ??? Holysmokes....hope that's a misprint-

I would recommend pulling your knock sensor bracket & check the contact area, one side of mine had terrible contact (small eyebrow). I suspect it contributed to odd high knock counts prior to my build.

Chris@Rvengeperformance
10-19-2011, 10:23 PM
.0019 of course.

Rod and piston #6 is in. .002 on that one.

good idea about the knock sensor bracket.

Chris@Rvengeperformance
10-19-2011, 10:39 PM
fyi I had several rings that were nearly stuck in the grooves due to carbon.

1stStealthN/A
10-20-2011, 12:38 AM
Were all the oil holes in the oil ring lands plugged? I noticed they usually are after 125k miles. Did you remove the oil jets to clean the block? Looks good!

Chris@Rvengeperformance
10-20-2011, 01:42 AM
Were all the oil holes in the oil ring lands plugged? I noticed they usually are after 125k miles. Did you remove the oil jets to clean the block? Looks good!

they weren't plugged, but partially obstructed. I cleaned them out.

I didn't remove the oil squirters, always had good oil pressure, I don't think they are stuck open. If it was getting hot tanked I'd pull them.

AdamVR4
10-20-2011, 02:07 AM
Nice updates. Glad Chris could drop some knowledge in this bitch :D

Bummer about the main girdle. That would eat at me...

Chris@Rvengeperformance
10-20-2011, 02:21 AM
I'm going to grab another ring set though. I measured it again and it was .027, bigger than I am comfortable with. For $32 it isn't worth the risk to me.

The knick does bother me a bunch, there is still a low spot of course. If I took enough off of it to get rid of it completely I'm sure it would only make things worse. I'm going to just have to run it the way it is. The only other thing I could do is get a different crank or get this one cut. This should be okay, the spot is really small and there is no high spot.

To give you an idea how small it is, I had to spin the crank over a dozen times just to find it again.

AdamVR4
10-20-2011, 11:14 AM
To give you an idea how small it is, I had to spin the crank over a dozen times just to find it again.

haha... Don't sweat it then.

Chris@Rvengeperformance
12-02-2011, 09:52 PM
little update, gotta post pics later.

1. engine bay is painted.
2. switched to non aws reservoir to save space, clean stuff up.
3. Bottom end is totally together.
4. Oil pan, water pump, heads are on
5. having an issue with cam binding I'm working on this moment.
6. forgot to put bottom valve shims in and had to re-do all 24 valve springs with the heads on. Super easy compared to having the engine in the car. Used leakdown tester to keep the valves up and noted about 10-20% leakdown. Not bad for rings that are not broken in at all.
7. Got a good used transmission.
8. Ray/Steve is at the moment building my billet transfer case.
9. Dr750s are here.
10.I have a new wiring harness to replace the main fuse box and harness. Mine was apparently on fire at one point, so I'm going to replace the whole thing rather than hacking together some crap.

So, basically once I get the cam problem fixed I can wrap up the engine. Then I need to install the new wiring harness, port the stock manifolds, install the turbos, clutch, trans, and put it all back in the bay.

Tomorrow I'm going to swap my 300m shaft from my old trans to the newer one. Then I'm going to try to get the wiring done and the cams fixed. I may have to wait on some more cam caps to come in to fix the heads.

FeaRpb
12-02-2011, 09:57 PM
Love the progress so far.

Wish I was that far. What steps did you take to painting the engine bay?

markoverclock
12-03-2011, 06:43 PM
where did you get the new wiring harness?

Chris@Rvengeperformance
12-03-2011, 07:41 PM
where did you get the new wiring harness?

Used ..

Chris@Rvengeperformance
12-13-2011, 04:25 PM
Love the progress so far.

Wish I was that far. What steps did you take to painting the engine bay?

I basically moved as much stuff out of the way as I could and masked off the rest. I didn't really go overboard, just painted the areas that would be visible with the engine in. I went with gloss black. I'll try to post up a picture later.

I have tracking # for my transfercase coming from ray/steve. My case ended up needing a new spool.

I have got the cams to stop binding, I painted my rear valve cover to match the block, and I swapped my 300m output shaft into my newer transmission.

I also bought a 1996 stealth wing and I'm considering stop techs in the new few months.

Drweldin
12-13-2011, 06:20 PM
What was the deal with the cams? Mixed up caps?

Chris@Rvengeperformance
12-13-2011, 08:01 PM
apparently. I used some cams from several different heads and tried combinations until I got what I wanted. I also plastigauged them and made sure the clearance was right.

not perfect, but should be workable.

Drweldin
12-13-2011, 08:05 PM
Ahh...
What is the clearance on those out of curiosity...?

Chris@Rvengeperformance
12-13-2011, 09:25 PM
.002 to .0035 IIRC

Mine came out to .003.

Too little and you have binding, too much and you are going to lose some oil pressure.

Chris@Rvengeperformance
12-20-2011, 04:29 PM
well ETS is running a 17% off sale today, so I picked up one of their 3000gt front mount kits. Brushed stainless steel. I'm probably going to polish it a bit myself.

vr4tune
12-20-2011, 05:31 PM
I'm loving you car more and more. Did you go black IC core

Chris@Rvengeperformance
12-20-2011, 05:32 PM
I did leave the core plain. Need a little bling. Do not care for the driver side merge appearance, so I want that black.

Transfercase came in today :) Weighs about as much as 2 stockers.

Drweldin
12-20-2011, 06:22 PM
Hopefully you dont have any pulsation issues with the 750's and FMIC...that's no fun.

vr4tune
12-20-2011, 06:23 PM
Have them polish the ends

Chris@Rvengeperformance
12-20-2011, 06:55 PM
Hopefully you dont have any pulsation issues with the 750's and FMIC...that's no fun.

I have those issues with the 19Ts already. I'll make it work. The ETS is supposed to be better because of the merge.

Chris@Rvengeperformance
12-20-2011, 06:56 PM
Have them polish the ends

you mean the end tanks? I can handle it. I've done a bit of polishing before.

Drweldin
12-20-2011, 09:18 PM
What are you doing for headers? I see Gilbert has his ready....If I was deep in like you are I's probably be all over those....

Chris@Rvengeperformance
12-20-2011, 10:30 PM
What are you doing for headers? I see Gilbert has his ready....If I was deep in like you are I's probably be all over those....

Yeah I am thinking about it, but im not sure it is really good for any power or not. Stupid as it is, what really has me on the fence is my new oem heatshields wont fit.

JasonY
12-20-2011, 11:55 PM
Keep all your heat shields. That's faaaar from a stupid reason.

Jason

Chris@Rvengeperformance
12-21-2011, 10:57 PM
merry christmas from steve and ray:

http://www.chrisbehnken.com/Images/photos/EngineBuild/100_7947w67v_TbDr.JPG

Chris@Rvengeperformance
12-21-2011, 10:59 PM
here I was making sure my cams weren't warped. Runout was 1/4 of a thousandth. Well within limits.

http://www.chrisbehnken.com/Images/photos/EngineBuild/100_78561Gzg_49d8.JPG

trying to find my other recent pics, lost them somehow

vr4tune
12-22-2011, 04:39 AM
I see a new knock sensor! :) I put a new one in my car last year.

Chris@Rvengeperformance
12-22-2011, 10:53 AM
I see a new knock sensor! :) I put a new one in my car last year.

yep, didn't want to take any chances on that. expensive little guy

AdamVR4
12-22-2011, 11:46 AM
Well worth it though! I haven't had ANY issues with phantom knock since I put in a new knock sensor in 2004. Shits getting old now! haha

Is that just paint on the getrag cover and tail section? Awesome under the tree :D

Chris@Rvengeperformance
12-22-2011, 11:47 AM
Well worth it though! I haven't had ANY issues with phantom knock since I put in a new knock sensor in 2004. Shits getting old now! haha

Is that just paint on the getrag cover and tail section? Awesome under the tree :D

Yeah they paint them black.

FeaRpb
12-22-2011, 01:31 PM
Looks nice with the black paint. My housings are still in the box David mailed me them in :(

One day I will mail it off for Ray to assemble.

green-lantern
12-22-2011, 08:03 PM
merry christmas from steve and ray:

http://www.chrisbehnken.com/Images/photos/EngineBuild/100_7947w67v_TbDr.JPG

Hell yeah! So purty

How much was the knock sensor? I've been thinking of replacing mine. I know my engine is new but it sure seems like I can run a lot of boost without knock.

Chris@Rvengeperformance
12-22-2011, 08:43 PM
it may be a few posts back, it was like $120 IIRC

green-lantern
12-22-2011, 08:57 PM
it may be a few posts back, it was like $120 IIRC

Not too bad for an import I guess. Did you get it from cherry hill?

vr4tune
12-22-2011, 08:58 PM
I got mine for under $100. Shop cost.

HLxDrummer
12-22-2011, 09:06 PM
I am super jealous... Would love to tear my car down and rebuild. Some day :)

Anyhow, how was putting in the 300M? I have a new Getrag sitting here but I'm real scared to crack it open to put in something I don't *have* to put in. (Worried it will leak/etc.)

Chris@Rvengeperformance
12-22-2011, 10:19 PM
I am super jealous... Would love to tear my car down and rebuild. Some day :)

Anyhow, how was putting in the 300M? I have a new Getrag sitting here but I'm real scared to crack it open to put in something I don't *have* to put in. (Worried it will leak/etc.)

That's easy I could walk you through it. They don't leak if you don't pry them apart. Tap the dowels when splitting the case.

Chris@Rvengeperformance
12-22-2011, 10:20 PM
Not too bad for an import I guess. Did you get it from cherry hill?

Yes, I get all oem parts from them.

Chris@Rvengeperformance
12-22-2011, 10:21 PM
Looks nice with the black paint. My housings are still in the box David mailed me them in :(

One day I will mail it off for Ray to assemble.

Should do now. Special price of $225 until jan 1

Going up to 375 or something like that after the 1st

HLxDrummer
12-22-2011, 11:15 PM
That's easy I could walk you through it. They don't leak if you don't pry them apart. Tap the dowels when splitting the case.

Sweet, I'll probably take you up on that offer down the road. Now I just need to decide if I should put it in right away or not in case I need to use the 1 year warranty lol

Wish you the best of luck with your project and I am looking forward to seeing some pictures/videos/timeslips!

Ninja Performance
12-24-2011, 12:02 AM
.002 to .0035 IIRC

Mine came out to .003.

Too little and you have binding, too much and you are going to lose some oil pressure.

The tighter you go also raises oil temps.

20 is good on rods. 25-30 on the crank works well.

-Chris

Chris@Rvengeperformance
01-07-2012, 12:49 AM
The tighter you go also raises oil temps.

20 is good on rods. 25-30 on the crank works well.

-Chris

hey Chris, those measurements were the camshaft journals.

Here are a couple of pics since I lost the others:

http://www.chrisbehnken.com/Images/photos/2012/100_795409QH_2889.jpg

http://www.chrisbehnken.com/Images/photos/2012/100_7957vi41_34dH.jpg

http://www.chrisbehnken.com/Images/photos/2012/100_7971N0YF_ad6i.jpg

http://www.chrisbehnken.com/Images/photos/2012/100_7968U6T1_959u.jpg

Ordered a stoptech 332 kit today from SuperCar. Phil was great as ever.

keo92stealth
01-07-2012, 11:18 PM
where is the pick of those 750's? lol

Chris@Rvengeperformance
01-07-2012, 11:26 PM
haha still in the box. Hope to get them mounted this weekend or early next week. just gotta finish the timing belt and get the manifolds on.

keo92stealth
01-08-2012, 10:04 PM
haha still in the box. Hope to get them mounted this weekend or early next week. just gotta finish the timing belt and get the manifolds on.

cool. in for some pics when u get them manifolds and bad ass turbos mounted!

Chris@Rvengeperformance
01-11-2012, 11:12 PM
mounted my ets fmic core today. Had to chop up the stock crashbar brackets really good since I don't have the stock crashbar anymore:

http://www.chrisbehnken.com/Images/photos/2012/100_79866l38_9dnK.JPG

the core is a beast

CoopKill
01-11-2012, 11:45 PM
Doesn't look like it will fit when you get it. lol

I had my questions about it until it was in place.

Chris@Rvengeperformance
01-11-2012, 11:47 PM
yeah it is about the biggest core you could go with without really hacking some stuff up.

mb3000
01-11-2012, 11:49 PM
That's 3.5" thick right?

CoopKill
01-11-2012, 11:50 PM
That's 3.5" thick right?

Yes it is

keo92stealth
01-11-2012, 11:56 PM
endtanks look sick bro. good quality product for sure from ets.

mb3000
01-12-2012, 12:00 AM
Being that it is a quality core I'm sure you won't have any overheating issues from the extra half inch. Probably couldn't say the same about an ebay core of the same dimensions.

vr4tune
01-12-2012, 12:16 PM
Being that it is a quality core I'm sure you won't have any overheating issues from the extra half inch. Probably couldn't say the same about an ebay core of the same dimensions.

This is very true!

FeaRpb
01-12-2012, 12:37 PM
Damn you Gump, stop copying me! :P

Looks awesome!

Chris@Rvengeperformance
01-12-2012, 12:58 PM
haha, just trying to get the good stuff

FeaRpb
01-12-2012, 01:02 PM
Seems like we both are ;)

We know quality.

green-lantern
01-12-2012, 04:03 PM
This car is going to be so fun to drive. :bigthumb:

Chris@Rvengeperformance
01-12-2012, 04:18 PM
Being that it is a quality core I'm sure you won't have any overheating issues from the extra half inch. Probably couldn't say the same about an ebay core of the same dimensions.

I had zero overheating with the cxracing core that was 3" thick. The 3sx single pass radiator works great.

I have to get the bumper on and see what ducting is going to be necessary. The ducting I made for teh cxracing core won't even begin to fit since the core is so much bigger. I may only end up needing some foam around the left and right side sto seal the bumper to the end tanks.

I hope that it is fun to drive. If I get 80% of the potential from my parts I have I'm sure it will be great.

I know it looks like I'm throwing a bunch of money at a mountain of parts, but that doesn't equal a great car. You can spend as much as you want on parts, but what matters is how it is all put together and how you work out the bugs and get a great tune. I *think* I have enough experience with prior setups to get this combo of parts working well and not have a car that looks great on paper, but can't make it down the track or drive cross country.

I almost have the engine dressed and ready to drop in. The biggest thing I have left is to get the new underhood wiring harness installed, I think that is going to be a royal pain in the ass.

green-lantern
01-12-2012, 08:43 PM
Seems like the right parts too me so yeah, as long as you get a good tune on it then it should be very fun to drive. I'm jealous as hell over the DR750's.

keo92stealth
01-12-2012, 08:52 PM
what are you tuning with? sorry if this has already been asked. 750's are bad ass!

Chris@Rvengeperformance
01-12-2012, 09:37 PM
emanage ultimate

green-lantern
01-12-2012, 11:43 PM
emanage ultimate

http://www.3sgto.org/f2/so-who-wants-their-ecus-chromed-7175.htm

Think about it

Chris@Rvengeperformance
01-12-2012, 11:59 PM
yeah I have. Once all the features are there I'll probably switch to that. As far as I know there is no 2 step support yet and I'd still have to use the emanage for speed density.

J. Fast
01-13-2012, 01:57 AM
Wow, that's a big ass core! Looks like you're getting close. Might want to put a heatsink on the power steering line before you sandwich it between your core and that radiator. The res will start to cavitiate when the AWS is active when you block off the front real bad like that.

How long till you drop it in? One last question, are you going to give your newborn baby a name?

Chris@Rvengeperformance
01-13-2012, 10:55 AM
Wow, that's a big ass core! Looks like you're getting close. Might want to put a heatsink on the power steering line before you sandwich it between your core and that radiator. The res will start to cavitiate when the AWS is active when you block off the front real bad like that.

How long till you drop it in? One last question, are you going to give your newborn baby a name?

There is no AWS on this car.

I'm not really sure when I'll get to drop it in, I'm hoping to have it running in February. It takes me a long time because I do not have very much time at all to work on it and I can be somewhat of a perfectionist. For instance my valve cover bolts look like shit, so I have another order from mitsu for those I'm waiting on. My flywheel shield is also really rusty and they are only $20 from the dealer, so I just ordered a new one, rather than try to refurbish this old piece of shit.

Then my thermostat housing is dirty looking, so I'm going to spend an hour or 2 cleaning that up. Plus it seems like every damn aluminum thread on these cylinder heads is bad. I had to helicoil the engine lift bracket on the front head. Then you may have saw all the problems I had with the cam caps. Little stuff like that really prolongs things.

I'm still debating putting the engine and trans in together as one piece or not. It is really easy with the engine hoist to get the trans mounted up and if I mount the engine first it will make lining up the motor mounts a lot easier and I can get this damn engine and stand out of my way.

I haven't really thought of a name, but if it was going to have vanity plates they'd read "Bad Day". We drove straight to Columbus Ohio and back in one day to pick it up about 5 years ago. I drove the whole way because my wife wasn't feeling well. It also had quite a few issues on the way back, so it was really altogether not a good day.

green-lantern
01-13-2012, 07:46 PM
I definitely like to drop the trans a engine at the same time. I find dealing with the motor mounts easier than aligning the trans after the engine is in. It's f-ing tight though. I'll use a hydraulic jack under the trans to level the engine when putting the bolts in the mounts.

CoopKill
01-14-2012, 02:28 PM
how high do you have to jack stand the body to get both out the bottom?

Sorry for the hijack...

JasonY
01-14-2012, 02:59 PM
As high as possible to get the trans out the bottom, do all the top work before raising the car to final height. Cherry picker makes dropping the trans one very easy job if you strap it right or hang it from a bolt on the shift levers.

Jason

Chris@Rvengeperformance
01-14-2012, 03:22 PM
yeah I don't think you are going to get the engine out the bottom without a lift or forklift.

Chris@Rvengeperformance
01-17-2012, 09:01 PM
stoptech came in today, thanks Phil:

http://www.chrisbehnken.com/Images/photos/StopTech/100_7990a4gi_17vi.jpg

http://www.chrisbehnken.com/Images/photos/StopTech/100_7992ORVZ_839O.jpg

http://www.chrisbehnken.com/Images/photos/StopTech/100_799376cd_03F7.jpg

http://www.chrisbehnken.com/Images/photos/StopTech/100_79959q3H_fjlw.jpg

http://www.chrisbehnken.com/Images/photos/StopTech/100_7996128n_4xac.jpg

http://www.chrisbehnken.com/Images/photos/StopTech/100_7998Smwk_0fz9.jpg

looks like the stoptechs come with their own brand pad now instead of axxis ultimates. We'll see how they do, may switch to carbotech.

Ninja Performance
01-18-2012, 12:34 PM
nice brakes, coulda saved you money on them ;)

StopTech - Ninja Performance - Affordable Performance Auto Parts (http://www.ninjaperformance.com/index.php?cPath=337_49400048)

Just sayin

-Chris

Chris@Rvengeperformance
01-18-2012, 12:46 PM
nice brakes, coulda saved you money on them ;)

StopTech - Ninja Performance - Affordable Performance Auto Parts (http://www.ninjaperformance.com/index.php?cPath=337_49400048)

Just sayin

-Chris

hey Chris would've loved to get them from you, but I worked out a deal with Phil before you started selling them. I got them for an absolutely smokin deal.

Ninja Performance
01-19-2012, 10:20 AM
Awesome, and Phil is a great guy! so no worries.

-Chris

Chris@Rvengeperformance
01-22-2012, 08:26 PM
Made some progress.

fully timed, manifolds are on, turbos are in, turbo oil lines are installed, valve covers are installed again. Water housing is installed, but I'm going to have to pull it back off because it is a little too high for the coil bracket to mount up right.

We also have the old main wiring harness pulled out from the driver side and under the radiator. The new harness is installed behind the fuse box inside the driver side footwell and ran half way up the driver
fender. That was a big, big pain to do.

All of the hoses on the water housing are being replaced.

Please keep in mind this isn't a show engine and by the time this is installed the overspray and what not shouldn't be visible:

http://www.chrisbehnken.com/Images/photos/2012/100_8000t16k_41MR.JPG

http://www.chrisbehnken.com/Images/photos/2012/100_8002T3ZQ_B01f.JPG

keo92stealth
01-22-2012, 08:31 PM
nice. making good progress!! is going to be very fun real soon for ya!

Chris@Rvengeperformance
02-11-2012, 07:20 PM
I've got a ton done since I lasted posted, I'll post some more details later.

The main thing on my mind is the clutch. I really am not sure about the act street clutch I have. It is rated at 540 ft/lbs. I can run it and see what happens, but dropping the trans isn't the funniest thing in the world. I can give up some driveability and get a 6 puck disc for this clutch that is rated for 690 ft/lbs really cheaply or I'm thinking of the stage 3 or stage 4 fe clutches from southbend.

What do you guys think? I don't put a lot of miles on the car, so even the 6 puck would last a long time, but I don't it to drive like crap around town. I don't have any experience in this area, I've always run full face clutches.

I really should've picked up an ofe clutch on ips's black friday sale :(

keo92stealth
02-11-2012, 07:26 PM
I've got a ton done since I lasted posted, I'll post some more details later.

The main thing on my mind is the clutch. I really am not sure about the act street clutch I have. It is rated at 540 ft/lbs. I can run it and see what happens, but dropping the trans isn't the funniest thing in the world. I can give up some driveability and get a 6 puck disc for this clutch that is rated for 690 ft/lbs really cheaply or I'm thinking of the stage 3 or stage 4 fe clutches from southbend.

What do you guys think? I don't put a lot of miles on the car, so even the 6 puck would last a long time, but I don't it to drive like crap around town. I don't have any experience in this area, I've always run full face clutches.

I really should've picked up an ofe clutch on ips's black friday sale :(

looks like ur gonna have to upgrade there gump lol. we all now 750s make 600 ft lbs.

Ninja Performance
02-11-2012, 07:45 PM
Haven't heard anything bad from any of the high HP cars I have sold Southbend clutches to. So I would give a SB clutch a whirl!

-Chris

JasonY
02-11-2012, 08:11 PM
Abused the hell out of the SB 4FE in Todds car, drives like stock and holds 30+psi from DR750's...

Jason

Chris@Rvengeperformance
02-11-2012, 08:36 PM
Haven't heard anything bad from any of the high HP cars I have sold Southbend clutches to. So I would give a SB clutch a whirl!

-Chris

can you get just the disk from the stage 4 ofe? My pressure plate is like new.

TurboSinceBirth
02-12-2012, 02:03 AM
I had a Southbend Stage 4 FE clutch also. Pedal pressure was like stock. I never should have sold it because I bought it on IPS's black friday sale but I had to fund a 3S purchase. I currently have a Spec 3+ in the Stealth I plan to install DR-750s on. I'd go back to the Southbend Stage 4 FE in a heartbeat though.

Chris@Rvengeperformance
02-13-2012, 02:22 AM
I'm a little concered about the reports of the stage 4 fe fusing to the flywheel. Anyone have some input? I intend to slip it a bit when launching, I'm not going to dump it.

Sin'sVr4
02-13-2012, 02:29 AM
Just dump it. Ur all set on your tc right? I do 5600 dumps on my rps stage 4 and is still Amazing

TurboSinceBirth
02-13-2012, 02:35 AM
I'm a little concered about the reports of the stage 4 fe fusing to the flywheel. Anyone have some input? I intend to slip it a bit when launching, I'm not going to dump it.

Just don't hot lap it at the track and you'll be fine. Of the ones I've seen it lock up on they did back to back passes at the track with no breaks. Because of the material it's made out of it needs to cool down between heavy use. Slipping is going to heat up the clutch faster but I'm sure you know to preload the drivetrain then let the clutch out. :)

Chris@Rvengeperformance
02-13-2012, 02:43 AM
Just dump it. Ur all set on your tc right? I do 5600 dumps on my rps stage 4 and is still Amazing

I'd still prefer to slip the clutch a little bit to take the slack out of the drivetrain and not wear everything out for no reason. It should also prevent some wheelspin.

Chris@Rvengeperformance
02-13-2012, 02:44 AM
Just don't hot lap it at the track and you'll be fine. Of the ones I've seen it lock up on they did back to back passes at the track with no breaks. Because of the material it's made out of it needs to cool down between heavy use. Slipping is going to heat up the clutch faster but I'm sure you know to preload the drivetrain then let the clutch out. :)

pretty much any clutch I'd give 15-20 minutes break between passes anyway. Is this what we are talking about or do they need more time to cool then that?

Chris@Rvengeperformance
02-13-2012, 02:47 AM
I'm still on the fence about just getting a 6 puck disk. They are only like $150.00. I wouldn't have to worry about selling my pressure plate. It just sucks that I've never driven one to see how streetable it is.

kywhitelightning
02-13-2012, 05:54 AM
Build looks good so far man keep it up. I'm doing very similar things to mine but it seems every time I come to a point where I have to ask myself whether I should stay on the cheap or go all out I seem to already know the answer should be go all out. Your build is definitely going way faster than mine though as I'm at a financial halt due to moving.

That IC looks badass.

Jeff

Chris@Rvengeperformance
02-13-2012, 11:15 AM
Build looks good so far man keep it up. I'm doing very similar things to mine but it seems every time I come to a point where I have to ask myself whether I should stay on the cheap or go all out I seem to already know the answer should be go all out. Your build is definitely going way faster than mine though as I'm at a financial halt due to moving.

That IC looks badass.

Jeff

Thanks Jeff, in many respects that is how this build went. I hadn't planned on upgrading the turbos or FMIC at the beginning, but I have an online store that really took off last fall and I had good cash flow. Things have of course slowed down after Christmas, so I'm trying to reign in the budget. The clutch is the last big thing I need to decide on. The 750 ft/lbs rating on the fe clutch sure looks nice, but the price isn't super friendly and I'm still worried about the thing fusing. I don't abuse my clutch, but I got my best launches when I used it a bit to get the car rolling out of the hole hard.

The ETS kit makes the cxracing one look pretty pale in comparison. The piping on the csracing kit is really pretty good though, I'd upgrade just the core if you'd like to save a bunch of cash.

AdamVR4
02-13-2012, 11:40 AM
Just dump it. Ur all set on your tc right? I do 5600 dumps on my rps stage 4 and is still Amazing

You gotta slip the clutch for at least a fraction of a second. There's no reason to intentionally shock load your drivetrain. I'm not saying ride it; just hesitate with your foot on the way up.

TurboSinceBirth
02-13-2012, 12:12 PM
Do you have any idea how your ACT pressure plate compares to the RPS Maxx pressure plate? I don't know what the lb rating on the RPS pressure plate is but if it's similar I would just throw it back in with your old disc or buy a new OEM one. The RPS Maxx street clutch has already been proven to hold a great deal of torque. It was holding everything Matt could throw at it with his DR-750s.

Chris@Rvengeperformance
02-13-2012, 12:14 PM
Do you have any idea how your ACT pressure plate compares to the RPS Maxx pressure plate? I don't know what the lb rating on the RPS pressure plate is but if it's similar I would just throw it back in with your old disc or buy a new OEM one. The RPS Maxx street clutch has already been proven to hold a great deal of torque. It was holding everything Matt could throw at it with his DR-750s.

both are rated at about 30% more clamp load than stock. The RPS is rated at slightly more torque (580 vs 540). Since they both use the same disk the plates should be similar if not the same. The ratings may be different because the RPS plate is a couple percent heavier or one or the other may rate things differently.

I think Matt m is running the 6 puck rps disc right now.

The 6 puck act disc is rated at 690 or 150 ft/lbs more than the street disk.

lawdogg
02-13-2012, 06:11 PM
Adam, do you slip on street tires and slicks? I've always dumped on street tires because I know I'll spin, so that avoids shock loading the drivetrain. It's been good to me on good tracks, consistent 1.6x 60's all day, but consistent smoke shows on a shit track or if I don't hit up the burnout box first. But I've never ran slicks and I've seen trannies pop when the tires grab.

FeaRpb
02-13-2012, 06:57 PM
I will be using a Clutchmasters 700+ series on my build.

AdamVR4
02-13-2012, 07:32 PM
Adam, do you slip on street tires and slicks? I've always dumped on street tires because I know I'll spin, so that avoids shock loading the drivetrain.

You still shock loaded the drivetrain in order to break traction, didn't you? It's still all wheel drive and making all 4 tires break loose requires a pretty significant amount of torque.

Others have described the way I launch as a slip-dump. I don't use a 2-step or anything... I just go WOT and come out on the clutch in the ~5K range. As the clutch engages, I slow down my foot a bit, and once the car begins to roll I come all the way out. It all happens in a fraction of a second. I've only been to the track once with the slicks and tried to baby it out of the hole and broke a stock rear axle.

lawdogg
02-13-2012, 08:49 PM
You still shock loaded the drivetrain in order to break traction, didn't you? It's still all wheel drive and making all 4 tires break loose requires a pretty significant amount of torque.

Others have described the way I launch as a slip-dump. I don't use a 2-step or anything... I just go WOT and come out on the clutch in the ~5K range. As the clutch engages, I slow down my foot a bit, and once the car begins to roll I come all the way out. It all happens in a fraction of a second. I've only been to the track once with the slicks and tried to baby it out of the hole and broke a stock rear axle.

Definitely, but far less than putting that much torque into something with 4 tires worth of full traction! Who knows what the coeff of friction of a spinning tire is ... I'm sure there's data out there. But like anything there are a thousand ways to skin this cat, I just wonder what the pros and cons are of the slip-dump method. Your method probably takes more skill. The couple times I've tried it, I've just roasted the clutch. :(

Chris@Rvengeperformance
02-14-2012, 03:03 PM
well like a lot of things it looks like I'm going to be running a mutt clutch. ACT HD pressure plate with the southbend FE clutch disk. Assuming that they like almost all of our clutch people build their pressure plates off the same blanks and basic size it should work just fine.

Should be good for 700 ft/lbs or so and the price was less than half that of the whole southbend kit. MTC was able to get one for me.

I'm going to take some measurements of the stock disk and the fe disk to verify their thickness is in the same ball park. Not a definitive test since the feramic disk may need more air space when released to not drag, but it'll make me feel better.

If it doesn't drive right I'll pursue other options. Should be a beast. The act plate is really good, balanced and SFI approved.

Would anyone suggest methods for prepping the pressure plate? I was thinking of hitting it lightly with a medium scotchbright type disk on my die grinder just to knock off the old clutch material, but I'm not sure if that is more harmful than just letting the new more aggressive disk do that itself.

It is probably a waste of time, I'm sure the first couple starts will have the old material abraded away.

The flywheel is getting resurfaced today at auto tire and parts. Their machine shop has been good. We have one of the biggest auto tire and parts stores here in cape and I believe it is the founding store. Very fast turnaround, same day and I didn't ask for any type of rush.

Chris@Rvengeperformance
02-14-2012, 03:16 PM
here is some info for your guys. ACT would not tell me what the pressure plate load in lbs is, but they said that the MB019 pressure plate is a 30% increase over stock.

Stock pressure plate clamp load in lbs is 2072 lbs. Adding the .30 increase from act puts the act plate at 2693.6. I believe RPS rates their plate at 2900. I do not know what southbend rates theirs at now, but I read in the past that it was 2750 lbs.

Should be a good match. FYI that puts the act plate at about 8% less clamp load than the RPS. Even if the 750 ft/lbs rating of the southbend clutch is with a 2900 lb press plate that should still put my mutt clutch's torque capacty at about 690, which will certainly be plenty for all but the absolutely max effort DR750 setup.

AdamVR4
02-14-2012, 05:23 PM
well like a lot of things it looks like I'm going to be running a mutt clutch. ACT HD pressure plate with the southbend FE clutch disk. Assuming that they like almost all of our clutch people build their pressure plates off the same blanks and basic size it should work just fine.

Should be good for 700 ft/lbs or so and the price was less than half that of the whole southbend kit. MTC was able to get one for me.

I'm going to take some measurements of the stock disk and the fe disk to verify their thickness is in the same ball park. Not a definitive test since the feramic disk may need more air space when released to not drag, but it'll make me feel better.

If it doesn't drive right I'll pursue other options. Should be a beast. The act plate is really good, balanced and SFI approved.

Would anyone suggest methods for prepping the pressure plate? I was thinking of hitting it lightly with a medium scotchbright type disk on my die grinder just to knock off the old clutch material, but I'm not sure if that is more harmful than just letting the new more aggressive disk do that itself.

It is probably a waste of time, I'm sure the first couple starts will have the old material abraded away.

The flywheel is getting resurfaced today at auto tire and parts. Their machine shop has been good. We have one of the biggest auto tire and parts stores here in cape and I believe it is the founding store. Very fast turnaround, same day and I didn't ask for any type of rush.


If you've got brand new surfaces, simply use brake cleaner to ensure there's no grease or oil on the flywheel or pressure plate surfaces and let 'er rip...

That's how I've always installed clutches on my car and locals' cars. If reusing a pressure plate, yeah, hit it with sand paper or potentially a scotchbright pad. I've only had one cluth fail -- I tried to reuse an RPS pressure plate by having it resurfaced for a 6 puck. I destroyed that clutch the first time I took it to the track, heh... There were sparks flying out from beneath the bottom of my car. Resurfacing the pressure plate reduces the clamp force. I don't recall how much the machine shop removed, but I immediately called RPS and they said that should be OK. Guess not.

Chris@Rvengeperformance
02-14-2012, 05:39 PM
If you've got brand new surfaces, simply use brake cleaner to ensure there's no grease or oil on the flywheel or pressure plate surfaces and let 'er rip...

That's how I've always installed clutches on my car and locals' cars. If reusing a pressure plate, yeah, hit it with sand paper or potentially a scotchbright pad. I've only had one cluth fail -- I tried to reuse an RPS pressure plate by having it resurfaced for a 6 puck. I destroyed that clutch the first time I took it to the track, heh... There were sparks flying out from beneath the bottom of my car. Resurfacing the pressure plate reduces the clamp force. I don't recall how much the machine shop removed, but I immediately called RPS and they said that should be OK. Guess not.

The pressure plate has a couple thousand on it, but it looks practically new. No warps, scores, or hotspots. I'll probably go over it really lightly just to get some of the old clutch material off.

Like you I'm reluctant to have any machining done to the plate, but it should not be needed.

Machine shop called and they were concerned that there is apparently no spec for how thick the flywheel needs to be from the clutch surface to the bolt hole surface, but I had them cut it anyway. They knew exactly what the step height should be. When I get it back I'm going to make sure that there is a little bit of a step where the friction surface meets the casting. RRE says that as long as you have a step there it is ok to resurface.

They shouldn't have had to take off much, you could still see the maching marks from the last time this flywheel was cut.

Chris@Rvengeperformance
02-14-2012, 06:31 PM
just got the flywheel back. It looks perfect. The price was a little steep ($78), but they got it done a couple hours after I dropped it off and they got the step height right. .826" They only had to take .0045 off of it, so I'm happy about that.

http://www.chrisbehnken.com/Images/photos/ACTCLUTCH/100_8039N9Q8_G9ne.JPG

Ninja Performance
02-15-2012, 05:32 PM
Nice, Just ALWAYS check with a mic when you get it back. I have found a few off in my years of having them turned. And yeah, $78 is a bit much. Normally a place like NAPA will do it for $35-$45

-Chris

Chris@Rvengeperformance
02-15-2012, 05:37 PM
yeah that is a great tip, going to double check it before installing. I'm happy that the RA seems pretty low. The machining marks are smoother this time than before.

Chris@Rvengeperformance
02-20-2012, 03:25 PM
well I got the south bend stage 4 fe clutch disc today and it looks really beefy. It is a modified stock plate of course. The hub and spring/marcel assembly is exedy/daikin like stock, but there is nothing wrong with that.

The friction surface is a little hard to measure since you can easily compress the disc by accident when measuring, but after carefully measuring it quite a few times I have these values

Stock disc with a couple thousand miles and 2 or 3 launches = .354 inches.
Southbend Stage 4 FE disk new = .358 inches

Looks like the fe disc, like others is built to stock dimensions, but that is pretty much where it ends. The material is obviously a lot closer to iron than the organic stock disc. I can see how this could take a beating. It looks like it should last a long time as well, there is a lot of material.

I cleaned up the pressure plate with an abrasive scotchbrite disc and it looks great with no scratches.

I had a few places on the firewall to cleanup and add brake line brackets to support the new stock lines. Everything is ready to go. My buddy is coming back over saturday to drop the engine and trans in.

Chris@Rvengeperformance
02-20-2012, 04:10 PM
MTC got back to me with info on the southbend pressure plates. They are rated at 2690 ft/lbs, which is exactly the same as my act plate. Should be good for the full 750ft/lbs.

Chris@Rvengeperformance
02-25-2012, 08:11 PM
engine and trans are in :)

lawdogs trick of sitting on a chair while trying to push the trans on the engine worked perfect.

vroom4
02-25-2012, 11:16 PM
tricking your dad into helping with beer works better :)

n2nsanity
02-26-2012, 03:45 AM
Nice, Just ALWAYS check with a mic when you get it back. I have found a few off in my years of having them turned. And yeah, $78 is a bit much. Normally a place like NAPA will do it for $35-$45

-Chris

I was thinking the same thing. Looks good though.
I bought a new one for $35 lol

Chris@Rvengeperformance
02-26-2012, 01:31 PM
I was thinking the same thing. Looks good though.
I bought a new one for $35 lol

you bought a new AWD flywheel for $35?

n2nsanity
02-27-2012, 01:33 AM
Mine is FWD and after looking, apparently very few stores carry the AWD for some reason, so sorry can't help there.
I forgot they had some differences. It looks the same tho.

I called Oreillys to see if they would turn mine. Was $20 or $30 I think.
Then I figured out that I could buy a new one for $35 so I just did that instead. Made by perfection and carried at Adv Auto.
I get almost all my stuff from them at about 40% off :)
Glad to help anyone here do the same if they're interested.
I'd imagine an AWD flywheel would probably be $400 from the stealership.

Anyway my point is I'm surprised they charged that much for resurfacing it. I called a few places and was quoted in the $20 - $40 range.

Yours looks great tho :)

IPD
02-27-2012, 02:55 AM
problems sourcing awd parts? who knew!

Ninja Performance
02-27-2012, 09:23 AM
Mine is FWD and after looking, apparently very few stores carry the AWD for some reason, so sorry can't help there.
I forgot they had some differences. It looks the same tho.

I called Oreillys to see if they would turn mine. Was $20 or $30 I think.
Then I figured out that I could buy a new one for $35 so I just did that instead. Made by perfection and carried at Adv Auto.
I get almost all my stuff from them at about 40% off :)
Glad to help anyone here do the same if they're interested.
I'd imagine an AWD flywheel would probably be $400 from the stealership.

Anyway my point is I'm surprised they charged that much for resurfacing it. I called a few places and was quoted in the $20 - $40 range.

Yours looks great tho :)

A lot of times, the 3S FWD parts are easy to find cause they cross reference to Eclipse.
The AWD parts however cross to nothing. There were only 15,000 VR4s made, so parts stores don't stock parts for them. unless they cross to something else.

-Chris

Chris@Rvengeperformance
02-27-2012, 10:49 AM
problems sourcing awd parts? who knew!

WOW THANKS! That made my day and really added valuable insight to my build!

Ninja Performance
02-27-2012, 11:37 AM
WOW THANKS! That made my day and really added valuable insight to my build!

my thoughts :lol:

IPD
02-27-2012, 12:42 PM
:p

just one more excuse to use DSM parts everywhere you can. ...including transmissions.

Chris@Rvengeperformance
02-27-2012, 12:49 PM
:p

just one more excuse to use DSM parts everywhere you can. ...including transmissions.

You can get an AWD flywheel resurfaced with no problem. I literally drove 1 mile to the machine shop and picked it up 4 hours later.

Posts like yours are what make threads a pain in the ass to read a couple years later when they come up in search results.

IPD
02-27-2012, 12:59 PM
You can get an AWD flywheel resurfaced with no problem. I literally drove 1 mile to the machine shop and picked it up 4 hours later.

Posts like yours are what make threads a pain in the ass to read a couple years later when they come up in search results.

if there were only serious posts everywhere, this would be a journal, not an internet forum. lighten the fuck up. your experience simply underscores the difficulties to be had with sourcing MTX parts at times. call an orange an orange.

Chris@Rvengeperformance
02-27-2012, 01:07 PM
if there were only serious posts everywhere, this would be a journal, not an internet forum. lighten the fuck up. your experience simply underscores the difficulties to be had with sourcing MTX parts at times. call an orange an orange.

I had zero difficulties securing any and all parts I need for my Getrag, thank you. Not sure what your problem is, please go post another ATX is the roxors thread somewhere else.

green-lantern
02-27-2012, 01:11 PM
tricking your dad into helping with beer works better :)

I hope my son tricks me into car work for beer someday :)

JasonY
02-27-2012, 11:57 PM
Chris, if you are gonna run meth, stay under 600cc, both of todds broken engines point straight to the meth altering the burn enough for the stock knock sensor to not hear knock.

Jason

Chris@Rvengeperformance
02-28-2012, 02:01 AM
Chris, if you are gonna run meth, stay under 600cc, both of todds broken engines point straight to the meth altering the burn enough for the stock knock sensor to not hear knock.

Jason

I'm definently going to keep that in mind and I don't plan on runnning a ton of boost anytime soon unless I have some race gas. Going to need more injector for that, but I want to get everything broken in first.

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8046Ztp3_8E0f.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8047dsm3_ACx1.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8048Dw8o_asPU.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8049X4Zu_a8Ou.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_80507Z3d_s3UZ.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8051z9Q3_4A2k.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8053rPV5_B423.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_8055K23Y_Tz4n.JPG

http://www.chrisbehnken.com/Images/photos/EngineIN/100_80599E9T_J0i5.JPG

Chris@Rvengeperformance
02-28-2012, 02:02 AM
any of you guys who've done this before know what I'm doing leaning over the driver fender :)

Sin'sVr4
02-28-2012, 02:05 AM
lol ive done that many of times. Looks great bro!

Chris@Rvengeperformance
03-05-2012, 11:56 PM
thanks guys I've installed so much crap I can't remember, but I'll try

1. Billet transfercase, damn the new spool splines are a tight fit on the output shaft! Should last a long time Fit great and thanks to Ninja Performance I had all 5 bolts :) I lost one of the original ones when I was running a brace. I ordered some MSD plug wires from ninja and he threw in the bolt I needed for free.

2. Engine wiring, replaced the front 3 injector plugs and pigtails. Fixed the rear o2 plugs. After cutting away the insulation I found that there was 2 bare wires in the bundle. I'm sure that explains my erratic fuel trims and o2 behavior.

3. Battery tray, battery, misc wiring.

3. Front axles, my bracket bolt repair seems fine. I found that allen bolts give greater access.

4. crank pulley torque.

5. oil pressure sending installed.

6. Brakes and clutch bled. Replaced the previous ghetto clutch slave line. Apparently at some point the stock flex line was replaced with a hard line. There was no flex at all, lol. Worked that way for 5 years believe it or not! I replaced it with a stainless clutch line.
blah blah

the important part is I cranked it over to prime it. It built up great pressure cranking. I got 20-25 PSI after 10 seconds of cranking. Plugs are out and battery is strong. Very happy. A couple burts of this and oil was coming out of the turbo returns just fine. Engine sounds good and even just turning over and it popped a plug out I just had sitting in the plug well so it makes compression haha. No horrible valve train noises which was a relief.

Should be running any day now, I just have to install the intercooler piping, radiator, intake pipes, and some other misc bullcrap. Well and the bumper and hood, but that can come after starting.

Ninja Performance
03-06-2012, 11:12 AM
Coming along great. :biggrin:

-Chris

vroom4
03-06-2012, 01:34 PM
Almost there! It is a great feeling to see that 25 psi at idle :)

Chris@Rvengeperformance
03-06-2012, 02:13 PM
it wasn't idleing. It made that much just on the starter. I haven't fired it up yet.

vroom4
03-06-2012, 02:53 PM
Yea, Im saying when you finally do it get started.

Chris@Rvengeperformance
03-06-2012, 04:28 PM
yeah hopefully. It made 20 before the teardown.

n2nsanity
03-06-2012, 09:03 PM
I like the custom crashbar much better than cutting out a section of the original.
Will it collapse at all or is it just solid?

wraith
03-06-2012, 10:32 PM
You will love the 750s. I went out for a spin and on a very rich tune, spun the rear tires at around a 40mph roll in gear by just pushing the throttle down halfway. I need to get my diffs in :) I have a stock 4 bolt with about 20k miles on it and Stage III DR heads. I hit 1.5 bar under 40000rpms in 2nd gear

Chris@Rvengeperformance
03-06-2012, 11:34 PM
I like the custom crashbar much better than cutting out a section of the original.
Will it collapse at all or is it just solid?

it bolts to the stock bumper shocks.

Chris@Rvengeperformance
03-06-2012, 11:35 PM
You will love the 750s. I went out for a spin and on a very rich tune, spun the rear tires at around a 40mph roll in gear by just pushing the throttle down halfway. I need to get my diffs in :) I have a stock 4 bolt with about 20k miles on it and Stage III DR heads. I hit 1.5 bar under 40000rpms in 2nd gear

nice.

are you able to run 1.5 bar on 93 octane?

Chris@Rvengeperformance
03-07-2012, 03:19 PM
I got a good question in a pm that I'd like to post, It has to do with why I'm only running 550cc injectors and what my power goals are:

"I didn't want to swap injector until the engine is at least broken in. If and only if I max these out to 100% will I go bigger. I am running 7 PSI over base fuel pressure and injecting alcohol, so the 550s should go pretty far.

I wasn't really planning on running much more than 500AWHP. I don't mean oh my dyno read 550AWHP one day, I mean backed up with track results, and the car actually makes it every day and doesn't blow up for years. If I do not trap north of 120 (hopefully 125) on pump gas I'll be disappointed.

I went with ported heads and the bigger turbos just to make it easier. I'm sure I could've got by fine with DR650s, but fast turbo response is one of my top priorities. Even the 19Ts were a bit laggy for my taste. I don't like having to downshift and wring the car out just to drive on the street and have fun on backroads and even just changing lanes. Maybe my old engine was just worn out enough to make them feel non responsive or the tune was wack, I don't know, but in the end they felt like a big turbo car without the big turbo power.

I actually miss my car when I first got it. It had a 9b and a DSM 13G. Holy shit that could spool up fast. It was like driving a big block v8. Just changing lanes on the interstate in 5th you could easily hit 15 PSI in a second. I'm hoping to recapture some of that magic and keep the car reliable. This isn't really a balls out build, just a good combination of parts that I'm only going to run at 80% most of the time."

IPD
03-07-2012, 03:28 PM
sound plan. is 1chp per cc of injector sufficient though?

Chris@Rvengeperformance
03-07-2012, 04:04 PM
sound plan. is 1chp per cc of injector sufficient though?

with the fuel pressure turned up and the alcohol injection it should be close to 550AWHP of capability, even at 11.5:1 AFR or so.

I think that is going to be enough for me. Hell I was probably doing good to make 400AWHP before. This will feel like ludicrous speed by comparison. If I end up needing more power than 550 it is going to put a lot of stress on my bottom end. I'm not going to chase power to the end unless someone like Ray has his hands on it.

That last 10% of power isn't worth 100% more stress on parts to me. I don't need to make 600AWHP to be happy.

FeaRpb
03-07-2012, 04:33 PM
Hey Forest, PM me the specs on your IC Core if you don't mind.

Chris@Rvengeperformance
03-07-2012, 05:36 PM
it is just the standard 3.5" thick one that comes with the ETS kit.

FeaRpb
03-07-2012, 06:00 PM
Ah okay.

keo92stealth
03-08-2012, 12:15 AM
with the fuel pressure turned up and the alcohol injection it should be close to 550AWHP of capability, even at 11.5:1 AFR or so.

I think that is going to be enough for me. Hell I was probably doing good to make 400AWHP before. This will feel like ludicrous speed by comparison. If I end up needing more power than 550 it is going to put a lot of stress on my bottom end. I'm not going to chase power to the end unless someone like Ray has his hands on it.

That last 10% of power isn't worth 100% more stress on parts to me. I don't need to make 600AWHP to be happy.

i see what you mean, but is the bottom built?