PDA

View Full Version : My lcdboostcontroller fun



RealMcCoy
09-05-2011, 11:23 PM
I bought a couple of these when they first came out for my own car and a customers build... I didn't have a chance to get mine working until after the 2nd gen was released, so I upgraded before It was ever installed. I thought I'd share what I did:

First my choice of mounting point. I simply velcro'd it to the shifter cable bracket...

http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/boostCntrl_3.jpg

My location for the switch is right under the center of the column. Since it's so well hidden, I wasn't worried much about a knob, A 1/4" vacuum cap worked great. (this is the original rotary switch, I'm not sure there's room to do this with the new one mounted to a circuit board)

http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/BoostCntrl_5.jpg


Now here's where it gets good.... I immediately saw an opportunity to pull a MacGyver and make a very low cost, extremely cool add on for this thing. Before I even contacted Antero about doing it, I went out to the parts shed, and scrounged the parts I needed to build my end. This is what I ended up with.

http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_11.jpg
http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_12.jpg

Now in case you didn't pick up on what I did from the pics, I used a GM ignition module to fashion a pump driver module for my water meth pump.... Now all I needed was 5V pulse width modulated controller to run it.

Gee, I wonder where I could get one of those...?

After a few PM's, Antero(Blackstealth) said he could do it... So when my upgrade board arrived, it had an extra cable hanging off it.

http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/boostCntrl_1.jpg

It took us a couple tries to get the code right, but amazingly, he had this whole thing whipped out in no time... I was starting to get a little worried about a pump surge problem I was having around 75% duty cycle. We came to the conclusion that it was primarily due to the low frequency of 31hz. since the output used had to be matched in frequency to the boost solenoid output, Antero didn't want to speed it up for fear of problems with the boost solenoid. I was a bit stumped, and in the meantime added a flyback diode to the motor that we had talked about. To my complete surprise, that entirely eliminated the surge. Yay... back on track :D

So here's some shot's of the current ramp on a scope, and the pressure output shown on graphing muti-meter. First at 30% duty cycle, and then at 100%.


http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_2.jpg
http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_1.jpg
http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_6.jpg
http://i90.photobucket.com/albums/k252/lnmccoy/ForumPics/alky_5.jpg


I just wanted to share my experience. Primarily just how awesome it has been to deal with Antero on this whole deal.... He was all about making this happen for no reason other than making something cool, and the possibility of expanding the capabilities of his design. He didn't charge me a dime extra to build the code, only for the materials used.(And I did offer, and fully expected to have to pay for his time..)

So this is a public THANK YOU to Antero for making my MacGuyver moment a reality

http://s90.photobucket.com/albums/k252/lnmccoy/ForumPics/?action=view&current=lcdBcntrl.mp4

CoopKill
09-06-2011, 12:05 AM
Nice!

Now I might need to send mine back... lol

J-Groove
09-06-2011, 12:23 AM
That is awesome.

I can't wait to install mine.
Just need to make room in the garage.

-John

Jimvr4
09-06-2011, 12:34 AM
Larry, really cool stuff. I'm impressed with your ingenuity :)

TurboSinceBirth
09-06-2011, 12:42 AM
Wow that is really cool. :) I may have to try that with meth injection even though I wanted to run ethanol. I've got mine and need to update it when I install it on the Stealth I'm buying. I'd really like to pick up a boost solenoid and get rid of my EBC altogether because this will pull boost when I hit knock which is what my Blitz SBC-iD already does but it's the next best thing to an AEM EMS, and I don't need to have a $400 boost controller sitting in the car.

BlackStealth
09-07-2011, 08:32 PM
In case anyone wants to copy RealMcCoy's alchy/water injection setup, it's just one wire that's soldered to the Generation 2's circuit board (to obtain the 5volt pulse-width-modulation). I did take a photograph of the circuit board+wire in case someone wanted to know where exactly. To access the alchy menus, it has to be unlocked by software. I can provide the flash software to unlock it.

HilbillyHomeboy
09-07-2011, 09:12 PM
This product is one of the most innovative ever for the 3/S. Massive thanks for the dedication, Antero.

Impressive out of the box thinking, Larry.

Both of you guys rock! :)

Jeremy

What_Turbo_Lag?
09-10-2011, 01:06 PM
this is incredible do you have instructions for mating up the GM ignition module and pump... so I can MacGyver one up too :)

RealMcCoy
09-10-2011, 01:24 PM
this is incredible do you have instructions for mating up the GM ignition module and pump... so I can MacGyver one up too :)

I had intended to post up a diagram. Just been busy. I'll get it done in the next day or so...

Jesters Deadd
09-13-2011, 06:09 PM
Thats pretty neat.

green-lantern
09-21-2011, 06:26 PM
how awesome it has been to deal with Antero on this whole deal.... He was all about making this happen for no reason other than making something cool, and the possibility of expanding the capabilities of his design. He didn't charge me a dime extra to build the code, only for the materials used.(And I did offer, and fully expected to have to pay for his time..)



Just saw this, pretty damn cool! and yeah Antero is great. He did some wiring for me (no charge)

Unlogic
12-25-2016, 02:59 AM
RealMcCoy, are you still running this setup?

RealMcCoy
12-25-2016, 03:47 AM
Yes I am... hasn't seen much use lately as my car is out of commission currently, patiently waiting for me to install it's new turbos... but hopefully soon we'll get put it to a real test... working on a three nozzle setup for the water/meth that I'm pretty confident won't have any distribution issues.

Unlogic
12-25-2016, 08:56 AM
Thats very interesting, would you mind sharing some details of you electrical setup?

I'm looking into building a similar setup but the 31hz limitation means that very few off the shelf PWM fuel pump controllers seem to be compatible.

BlackStealth
12-25-2016, 09:33 AM
Thats very interesting, would you mind sharing some details of you electrical setup?

I'm looking into building a similar setup but the 31hz limitation means that very few off the shelf PWM fuel pump controllers seem to be compatible.
Unlogic, since you're not using a boost solenoid, I can change the 31hz to whatever number you need. 31Hz came from the fact boost solenoid like to operate at this frequency. FYI, the alchy PWM and boost solenoid PWM both share the same timer, that is why they're linked together.

Unlogic
12-25-2016, 05:00 PM
That sounds great Antero, it makes things much simpler.

If you can change the frequency to be inside the 60 - 330Hz range it means we should be able to use a Ford/VDO pump driver module. It has Ford Part number 3W 83-9D372-AB, VDO number A2C53005489 and comes off a Range Rover.

It has a 6 pin connector which pinsout as follows:


1) 12v output to fuel pump
2) 0v return (low side PWM) from pump
3) pump drive signal from eng ecu, 60 to 330Hz, drive with open collector low side drive, 0 to 50% duty is 0 to 100% pump duty
4) not used
5) 12V power feed, ignition switched
6) 0v chassis ground

Found that information in this thread: http://www.pistonheads.com/gassing/topic.asp?h=0&f=66&t=916550&i=240

The only piece of information missing is the input voltage required for the pump drive signal.

Unlogic
12-25-2016, 06:18 PM
Using this Ford fuel pump driver module from a F150 truck seems like it could work too.

https://www.amazon.com/Dorman-590-001-Fuel-Driver-Module/dp/B005JJ0D22

http://www.dormanproducts.com/itemdetail.aspx?ProductID=48472&SEName=590-001

There is a good thread about it here:

http://www.msextra.com/forums/viewtopic.php?t=59992

The only downside is that it requires a 12v PWM signal.

BlackStealth
12-26-2016, 09:47 AM
I have a better suggestion, build your own MOSFET controller for $2.

Digikey parts list:
1 x IRLB8743PBF-ND (MOSFET, rated for 78 Amps)
1 x 1MWCT-ND (1 Mega ohm resistor)
1 x 1N4004DICT-ND (Diode)

Because it is so cheap, you might want to build another as a backup.

I'll draw the schematic diagram later tonight. This MOSFET has proven to be reliable for my 3D printer, running hours at a time.

Unlogic
12-26-2016, 10:32 AM
That sounds great!

I've been doing some research on water/meth injection controllers and the LCDBC has the potential to match some of the more expensive ones on the market.

Aquamist seems to be the brand to beat and their HFS-3/4 controller has the ability to start injection at a given pressure and base the amount of water injected on the injector duty cycle.

Given that the LCDBC already has the option to monitor the IDC I'm sure you'd have no problem matching that functionality.

BlackStealth
12-26-2016, 10:26 PM
Instead of Injector Duty Cycle, Injector pulse width would be better I would think. IDC requires two pieces of information from the ECU (Injector pulse & RPM) and IDC is known to be slightly incorrect at times (for technical reasons I'll leave out). I can do this programming, but I won't have time to do it immediately, maybe in a few days I can do it.

Here's the diagram for the 3 parts. I drew the pin out info for the MOSFET, also keep in mind you need to take static electricity precautions so you don't ruin the MOSFET during assembly.

The diode is on backwards on purpose. When the MOSFET disconnects ground from the pump, the motor's coils will generate a back EMF voltage, and this diode will safely dissipate this excess energy extending the life of electronics and a more stable output from the motor.

The 1 Megaohm resistor is on there to prevent an accidental turn-on.

I believe the MOSFET should stay "cool enough" ie. below 50C, if not add a heat sink to it.


http://i782.photobucket.com/albums/yy107/blackstealth_2009/LCDBC-alchy_1.jpg (http://s782.photobucket.com/user/blackstealth_2009/media/LCDBC-alchy_1.jpg.html)

Unlogic
12-27-2016, 03:34 AM
Thanks Antero, I've ordered parts for two amplifiers.

Unlogic
12-27-2016, 04:41 PM
I ordered this Snow performance kit today, it should be here within a day or two:

https://www.snowperformance.eu/media/image/product/2513/lg/en-water-injection-boost-cooler-stage-1.jpg

https://www.snowperformance.eu/en/water-injection/boost-cooler-stage-1#&gid=1&pid=1

My little borther is going to help me with the MOSFET controller in the mean time. He had an alternative approach he wanted to try based on a FQP50N06 TO-220 and a TC4427AEPA. Thats just numbers to me but we'll see how it turns out.

BlackStealth
12-27-2016, 08:18 PM
The FQP50N06 requires 10volts to turn on, it won't power on from the LCDBC 5v signal.
The TC4427AEPA current rating is too low.

Of course, I don't know what he had in mind, maybe he was going to run them in stages or something.

Unlogic
12-29-2016, 07:10 PM
I got all the parts for the water methanol injection now and the driver module seems to be working. I posted a short video of the setup in my build thread here:

http://www.3sgto.org/threads/10823-Slightly-tweaked-3000GT-TT?p=336832#post336832

Found out by testing that a PWM frequency of 100 hz seemed to work best with the Aquatec 5800 pump that came with the kit. Anything higher or lower gave suboptimal atomization a low duty cycles.

Is there a way to enable the current Alchy functionality in the 3.57 firmware or does it require a reflash with a special firmware?