View Full Version : Lean on cylinder 4? Logs/plug pics etc.
So after I fixed my fpr problem things were running great. Then on my last trip I was showing off and man... the car started breaking up pretty bad after 4-5k. Put the logger on it and sure enough, shit ton of knock and the rear seems to be running lean again. However, this time, the fuel pressure stays rock solid.
http://primaryboost.com/store/rt/leannum4/num4plug.png
I pulled the plugs and checked compression. 150,148,155,155,150,152 (1-6). I noticed plug #4 was much whiter and was flaky. I would assume this is the culprit cylinder.
(#3,4,5)
http://primaryboost.com/store/rt/leannum4/num4plug.jpg
Clogged injector? Something else? Curious if anyone has an idea of how one cylinder going lean would affect the afr after all three mix. Thoughts?
Thanks,
Antoni
KeithMac
08-11-2011, 05:56 PM
Missfires will show up as lean on the Wideband due to unburnt oxygen being passed straight through the engine.
One cylinder running lean will scew the whole bank reading..
The plug insulators look far too white for my liking, should be a brown/ tan colour unless youre running alky.
Well, injectors came back clean. None were having any problems. I swapped the plugs front/rear and gapped them lower. No change. Once it cools down I'm going to swap my windebands front/rear and see if there is any difference.
Missfires will show up as lean on the Wideband due to unburnt oxygen being passed straight through the engine.
One cylinder running lean will scew the whole bank reading..
The plug insulators look far too white for my liking, should be a brown/ tan colour unless youre running alky.
What type of problems would create the white insulators?
DocWalt
08-24-2011, 12:15 PM
Have you swapped injectors around?
Have you swapped injectors around?
I did, I swapped them for good measure even though they all flow tested fine.
DocWalt
08-24-2011, 12:31 PM
Have you checked the resistor pack? Made sure the connections to the injectors (electrical) were clean and secure? Have you swapped the front/rear widebands yet?
Have you checked the resistor pack? Made sure the connections to the injectors (electrical) were clean and secure? Have you swapped the front/rear widebands yet?
Well I swapped front/rear widebands today and the readings are correct. It is not a bad sensor. The rear bank is still running lean. I tried low boost and it still does the same thing. Will look into the resistor pack next.
vr4tune
10-05-2011, 07:04 AM
Have you done a compression test or cylinder leak down?
Have you done a compression test or cylinder leak down?
See initial post...
So after I fixed my fpr problem things were running great. Then on my last trip I was showing off and man... the car started breaking up pretty bad after 4-5k. Put the logger on it and sure enough, shit ton of knock and the rear seems to be running lean again. However, this time, the fuel pressure stays rock solid.
I pulled the plugs and checked compression. 150,148,155,155,150,152 (1-6). I noticed plug #4 was much whiter and was flaky. I would assume this is the culprit cylinder.
(#3,4,5)
Clogged injector? Something else? Curious if anyone has an idea of how one cylinder going lean would affect the afr after all three mix. Thoughts?
Thanks,
Antoni
DocWalt
10-05-2011, 10:18 AM
Good to see it's not the widebands. Sort of not good at the same time lol
Good to see it's not the widebands. Sort of not good at the same time lol
My thoughts as well. I put in new plugs and gapped them down a little. I'm curious to see if #4 still shows like it's burning leaner than the others or it was just due to misfires. Maybe something got damaged in the rear when my fpr was leaking fuel back to the tank. The car seems to run well aside from the rear being lean under load.
The resistor pack came back good, also checked the harness to rear injectors. No issues there; everything was in spec.
Any other thoughts on what can cause front/rear burn differences if fuel pressure is good?
So I did a couple more tests. I went back to a stock FPR instead of my AEM AFPR. Figured my fuel pressure would not drop after shutdown. For some reason it wasn't. So I swapped in my old walbro instead of the aeromotive stealth. Now I hold all fuel after shutdown. So I thinking maybe the aeromotive was the problem dropping pressure at higher rpm and since my sensor is at the front it wasn't showing the slight pressure drop of the rear. Did some WOT runs. Same problem. I noticed one other thing, right after an idle shutdown. I noticed my front lc1 was showing jerky results while the rear was solid. I can't remember if my swap test if I swapped sensors or lc1s so I wonder if one is bad showing incorrect results.
I ended up trying to tune it out and if I tuned by the rear wb then knock went away so that was definitively the culprit but now I don't know if the front is super rich. Here are the corrections I had to make
rpm dyno 111311a
400 0 0
800 0 0
1200 -3 -3
1600 10 10
2200 4.5 4.5
2800 5 5
3400 3 3
4000 0 1
4600 -8 -2.5
5200 -9 -2.5
5800 -9 -5
6400 -10 -8
7000 -12 -10
7600 -14 -12
Should be pulling the car out sometime soon. I got excited at first but then remembered I never solved this issue last year. Anyone have any other ideas as to what might be going on?
DocWalt
02-23-2012, 03:25 PM
Have you checked for any cracks in your headers?
Have you checked for any cracks in your headers?
I have replaced it last year but haven't checked it recently. Would that effect how a bank actually operates or just how the o2 sensors are reporting it? I say that because I am seeing knock without changing the tune and have to richen it up quite a bit just to fix some of it.
It's just really weird that I am having this problem twice within such a short span. The first being a worn ball seat orifice in the aem fpr. Then it was good for a couple weeks then the issue came back with no change in fuel pressure issues as when the fpr was bad.
DocWalt
02-24-2012, 06:01 PM
Oh, ok. It would cause one bank to lean out according to the O2 readings. If I think of anything else I'll post up.
Thanks, I think at this point I probably just need to stop screwing around and tear it apart.
Roybatty
02-24-2012, 07:20 PM
I was gleaning over the spark plug interpretation chart and it said the white flaky can be attributed to worn valve guides.
Well I noticed something interesting today. I was logging when starting up and noticed that it started off with the front and rear different. Then when the o2s starting cycling they came together. Is is possible that something is up when in open loop? Can I force open loop in other ways than cold startup and WOT?
http://primaryboost.com/store/rt/logs/031512_startup.png
So I tried swapping ECUs same issue still. I did manage to get some more logs together to see maybe what is going on here.
Here is a 3rd gear wot log
http://www.primaryboost.com/store/rt/logs/031512_wot_3rd.png
Here is a cruise, the guide lines represent the smoothed average. So yea, the rear (pink) is leaner.
http://www.primaryboost.com/store/rt/logs/031712_cruise_01a.png
Here is a wot with boost and fuel pressure in focus. The scales aren't quite the same but there is something interesting. Boost goes up .81 PSI but fuel pressure actually went down .7psi, so fuel pressure is off by 1.5psi. Not sure if that is anything significant. I would imagine this isn't exactly a big deal as both the front and rear would experience this?
http://www.primaryboost.com/store/rt/logs/031712_wot_01.png
This is a log of after I fixed my aem afpr last summer. I had a similar issue where the rear was running real lean and as it turned out the afpr was leaking because of a worn ball seat and dropping fuel pressure to the rear. You can see how nice this log is (except for the tune of course)
http://www.primaryboost.com/store/rt/logs/072011_wot_fixed_fpr.png
Did a leakdown test as well. I noticed a trend that the front have more leakage than the rear.
1:89
2:96
3:91
4:95
5:93
6:96
Could this difference be causing my issues?
Well, I think it's fixed! I only did one run because it's getting late and I don't like to do testing at night in case something breaks. After doing the leakdown I had everything apart so I decided to try and swap the front and rear injectors. Well I also tried to bend the injector pins to make a "sure" connection to the connectors. Well I did a run and booyah, front and rear now match up. Going to try a few runs tomorrow as well. I REALLY hope this is not a fluke I will be so pissed lol.
http://www.primaryboost.com/store/rt/logs/031812_fixed.png
DocWalt
03-18-2012, 10:43 PM
I wonder why the connectors would wear out like that... I hope it's fixed :p
I wonder why the connectors would wear out like that... I hope it's fixed :p
Assuming this really was the problem...
It's weird because they are brand new (<5k miles) injectors and I replaced the connectors with the MSDs about 15k miles ago. Maybe the injector pins are a hair thinner and the connectors are a hair looser?
Well I did a bunch of pulls on the way to work this morning. Looks like everything except the rich tune (to compensate) is good! AFRs match right up! So much fun to drive!
DocWalt
03-19-2012, 02:28 PM
Sweet. What an odd problem... Now you just gotta tweak the tune back a bit :p
Sweet. What an odd problem... Now you just gotta tweak the tune back a bit :p
Yup! Also, looks like I have to adjust my ebc, it seems to be rising a bit.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.