View Full Version : 1st gen vs. 2nd gen AC evaporators.
vr3.9
07-31-2011, 04:07 PM
The evaporator in my 91 is leaking. 1st gen part # 54750 94 + = 54708.
1st gens don't seem to be available anywhere accept dealer. 54708's can be had pretty cheap. The online pics look exactly the same. Just wondering if any one has ever compared the 2 evaporators to see if they could be interchanged. I would think the 2nd gen would be larger to help with the less cooling of the r134a. But if it physically fits I will just get one and use it.
Roybatty
07-31-2011, 04:14 PM
Been following your other posts on ac repairs. Subscribed. How did you determine your evaporator was leaking? Ultraviolet light and dye or could you tell while trying to hold vacuum?
vr3.9
07-31-2011, 04:35 PM
It quit working so well yesterday. Today I put the gauges on it and it had lost some freon. It has had a very small leak for a long time and just occasionally add some. The real problem was that low and high were perfect and the air coming out was only about 75 should be 10 or 15 degrees colder. I have noticed that sometime it doesn't cool well and the other times suddenly ice cold. So my expansion valve has been messing up for a while and now seems stuck. I was going to change it and decided to check the evaporator with the uv light and it has small traces of green kinda all over most of it. Looks like I may have found a few 1st gen evaporators online for pretty cheap. Just looks like I'll be without AC this week. It's only forecast to be 106 everyday......... it won't be too bad. ll
MaelstromOC
07-31-2011, 04:49 PM
Yeah, I've been really needing to change my A/C out for quite awhile, but it's a different issue. For some reason, the pulley on my A/C is for a 4-spline belt it seems whereas the rest of the pulley's on the car are 5-spline. Because of this, the belt has been ripped close to in half (Diameter wise, so it still works lol) but I can't really use my A/C for the belt slipping (which I attribute to the fact the belt is nowhere near as wide as it should be and as such, let's it slip like crazy. I bought a new A/C unit well over a year ago, along with a clutch kit for it and an expansion valve and evaporator, but I haven't been to have anyone pull a vacuum on the lines so I can swap the stuff out safely :( I had thought about just swapping the pulley out, but I learned very quickly that I can't just do that (the actual inner diameter of the new A/C pulley is quite a bit larger than the old)
Do you think it would be alright to only swap out the compressor since my expansion valve has always worked fine and the evap is fine as well (no leaks or anything)?
The heat sucks!
Roybatty
08-01-2011, 12:02 AM
Sorry to OP for the hijacking, but since you are new I am sure it won't be counted against you ;)
The long and short of it is, there is the right way which works if done correctly, and there is the not so right way which is cheaper and easier, but also may work or may not. Some people have resealed their system with O-rings, pulled a vacuum and once determined there were no leaks, refilled system with R134a. On the other extreme you should replace the ac compressor, evaporator valve, dryer, and all O-rings prior to refilling with R134a and PAG or ester oil. People on here have been successful doing both.
There are a couple of different threads out there that could help you. Some are on this site, and on the other. There is a difference in ac compressor for 91/92 models and later years. Evidently it is difficult to get a new 91/92 compressor but there are remanufactured ones available. Sounds like you may have picked up the wrong one.
You should glean thru these links if you haven't already.
http://www.3sgto.org/f18/ac-help-5477.html
http://www.3sgto.org/f2/second-gen-c-compressor-1g-5589.html
Also this site has a walk thru on changing out the ac compressor Stealth 316 Home (http://www.stealth316.com/0-home.htm)
Get a copy of the manual...you shouldn't have to pay for it...you should be able to find it for free...read up on the AC/Heater section.
vr3.9
08-01-2011, 01:09 AM
Since I've only changed out/converted 30 or 40 pretty sure I've got this down. The only difference between R12 compressors and R134a is the hose and pin connections. Pull the pins and they are all the same. The rebuild shop pulls all the pins so they never have to worry about it being the right compressor for the right year. You do need to replace the oil with pag and you should always replace the dryer when changing a compressor. . I am curious to know if there is a difference in the evaporators though. I would think they would be bigger to create the same amount of cooling. I am going to assume they are similar to the 92 GTO which came r134a. I have found a couple of places on line that claim to have them. Hopefully tomorrow I can get some one live and on the phone to verify their stock. I hate paying online only to be told it will be 6 weeks. Then it takes 3 weeks to get a refund.
Roybatty
08-01-2011, 10:00 AM
I have tried to pull vacuum. That little red Harbour Freight device seems to work ok, but the system doesn't hold any vacuum; evidently a major leak. I was going to pull the glovebox and look at the evaporator lines, pull fans and radiator to check the lines to the condensor, my compressor does't look very grimey...Then try hold vacuum again.
IIRC didn't someone get the evaporator from EBAY or was it just the evaporator valve?
vr3.9
08-01-2011, 11:19 AM
They have one on ebay but it says it's for a 94. That's why I wanted to know if it would fit. GOOD NEWS! Found a place on line that has them for 64.47. I called they have 4 in stock and like all good things..... their in the Dallas/Fort Worth area.
http://www.techchoiceparts.com/ShowItem/114924-1991%20-%201993%20Dodge%20Stealth%20Mitsubishi%203000GT%20 Evaporator%20Core.aspx
UTRacerX9
08-01-2011, 01:46 PM
Thanks for posting, I'll be picking one up as well. This past weekend, I spent a couple hours insulating my garage door, just so I could start working on my car again without dying from the heat. My A/C has a major leak, need to track it down and fix it before I do anything else.
vr3.9
08-01-2011, 02:00 PM
Thanks for posting, I'll be picking one up as well. This past weekend, I spent a couple hours insulating my garage door, just so I could start working on my car again without dying from the heat. My A/C has a major leak, need to track it down and fix it before I do anything else.
I should be getting mine tomorrow, I'll let you know how it goes.
I put a swamp cooler (evaporative cooler) in my garage. I open the attic to provide exhaust and cool the attic. Not a perfect solution but so far it's prove worth it. When it's over a 100 my garage will stay about 87 -88. Throw in the breeze it creates and I won't say you won't still sweat but at least I don't drip. For the cost of running a fan I can live with it.
UTRacerX9
08-01-2011, 02:35 PM
A buddy of mine just did the same thing I did two weeks before me, he said he noticed his garage temperatures were consistently 8-10 degrees cooler than they had been, I'm hoping to see similar results.
Roybatty
08-01-2011, 04:41 PM
I spent a year in Amarillo for work. I am familiar w/ the swamp cooler. I thought it worked well, its all I used there...something about the aridity.
Been using fans and working in evenings when cooler in the furnace garage.
connected via tapatalk
aaronatstate
08-01-2011, 10:56 PM
Everything I've seen the only major difference between the evaporators are alignment pins, just like the compressors. Though I dont have one of each in hand to compare.
Roybatty
08-02-2011, 04:10 PM
Quick question...anyone know the torque spec on the piping going in the ac compressor? I am going to use 9 ft-lbs, did not see it in the service manual.
vr3.9
08-03-2011, 12:33 AM
I got the evaporator in today. Didn't come with the stud for the low side or 0- rings for the high and low side. I put in a new expanison valve. Made in china, but for the price I can't complain. I have cold air again.
Roybatty
08-03-2011, 01:45 AM
Glad you got it worked out. I replaced orings @ condensor, compressor, receiver, and appurtnenant pipes. The good news is that its holding vacuum. I will slap the rest of it back tomorrow, charge it, and hopefully be getting cool air also.
Roybatty
08-03-2011, 07:13 PM
Put a bottle of uv dye in compressor, ester oil and 2 cans of r134a. She's cold now...just hope it lasts!
connected via tapatalk
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.