View Full Version : Installing catch can with krank vents with blow-thru fmic.
KPZVR4
07-30-2011, 12:29 AM
Ok, I got the last of what I needed today and I have treid to find the answers, but i'm just not sure.
Does anybody have info on what the best way to hook all this up together.
Thanks in advance.
I am doing this tomorrow night, so any help asap would be great.
TurboSinceBirth
07-30-2011, 03:46 PM
Why do you need a catch can? Install the big krank in the rear, the small one on the front, and instead of having the front one go to to the intake have it go to the catch can. Leave the exit line on the catch can off or put a filter on the catch can if you want. Any of the oil will stay in there. Otherwise, just route the front hose off the front krank vent to the ground. That's how I have mine setup.
KPZVR4
07-30-2011, 04:26 PM
I want to make sure she isn't smoking, or putting oil in the IC system. It seemed like a good idea, so I got the STM deluxe catch can with a filter and Krank vents. So, I am trying to get it all in today.
Any pics would be great if anybody has installed these together before.
Thanks for the reply.
KP
Roybatty
07-30-2011, 05:45 PM
There are a lot of threads, even on this relatively new forum, where both systems are explored. IIRC, big concern about boost and stock pcv valve.
connected via tapatalk
KPZVR4
07-31-2011, 09:25 PM
So, do I not need the can and the vents are good by themselves? If so, how would you do it?
Why do you need a catch can? Install the big krank in the rear, the small one on the front, and instead of having the front one go to to the intake have it go to the catch can. Leave the exit line on the catch can off or put a filter on the catch can if you want. Any of the oil will stay in there. Otherwise, just route the front hose off the front krank vent to the ground. That's how I have mine setup.
green-lantern
07-31-2011, 10:10 PM
You only need the can if you are pushing oil into the intake. The front Krank vent is for making sure your PCV valve can't leak and pressurize the crankcase. The rear one helps keep vacuum on the crankcase when off the throttle.
You do have one big one and one small right? (Krank vents)
KPZVR4
07-31-2011, 10:42 PM
Yes, I do have one big and one small. So, the can isn't needed? With blow thru, does it still go to the intake?
green-lantern
07-31-2011, 11:02 PM
Well a lot of times I think guys with blow through just vent to atmosphere on the rear one. I'd probably just run a hose under the car. With the rear Krank vent you wont have to worry about sucking in dirty air.
KPZVR4
07-31-2011, 11:19 PM
Are you saying open on both? Sorry your post is a little confusing.
green-lantern
07-31-2011, 11:28 PM
Sorry man, no, just the rear one. Instead of normally going to the bubble just run it to that catch can you got (put the valve in before the can) then run the other hose off that can under the car.
MADMarc
07-31-2011, 11:43 PM
Not to thread jack but aren't some people running the krank vents w/o a pcv valve or am I mistaken? I read a lot of pros and cons w/the krank vents on here and elsewhere, but does running them with the pcv valve mitigate the problems following install?
KPZVR4
08-01-2011, 12:21 AM
Krank vents are PCV valves. Just bigger and badder. From what i understand, if you remove the one on the front it whistles. I am probably gonna leave it on and run the krank after it.
green-lantern
08-01-2011, 01:42 PM
From what i understand, if you remove the one on the front it whistles.
I’ve heard that too
Also the PCV valve is designed to restrict flow at high vacuum. If it doesn’t I believe it causes idle/running problems. It’s basically unmetered air.
http://www.stealth316.com/images/pcv-operation.gif
More info here
Stealth 316 - ET Performance Karnk Vent Turbo Kit (http://www.stealth316.com/2-krankvents.htm)
MADMarc
08-01-2011, 02:26 PM
Well I'm in to hear about how this all goes for the OP.
TurboSinceBirth
08-01-2011, 02:38 PM
The rear krank vent I have venting to the atmosphere. I just ran a longer hose so it'll drain onto the ground. I wouldn't want that oil in my intake.
KPZVR4
08-01-2011, 07:11 PM
I am considering just leaving the catch can out. It's kinda big and I am not sure where I would put it. I stripped bunch of crap out of there to clean it up, so I am having second thoughts about putting it in. I thought originally that I would need it, but the more I read, it would seem like I don't really need it at all.
I am just not sure what I want to do. :)
Input welcomed.
green-lantern
08-01-2011, 07:20 PM
Just leave it out then. You probably don't need it.
NickS VR4
08-01-2011, 07:55 PM
I have heard of people still connecting a vacuum line pre-turbo. Why change the design of the system if you don't have to?
green-lantern
08-01-2011, 08:00 PM
I have heard of people still connecting a vacuum line pre-turbo. Why change the design of the system if you don't have to?
Because it has to do with emissions not performance mainly.
KPZVR4
08-01-2011, 09:46 PM
I totally laughed out loud when I read this. I don't think there is a single system left in my car that has not been changed. One more won' make much of a difference if it is an improvement. My car couldn't pass inspection if the mechanic was passed out. I still have a sticker tho. :)
Anyway. I just don't think I have a home in the engine bay for the can that I want to fill. If I don't need to put it in and address/eliminate the blowby without putting it in, I won't. I will run some hose off the rear to drain down low, but where should the front go if not to a catch can?
Thanks again for the input.
KP
I have heard of people still connecting a vacuum line pre-turbo. Why change the design of the system if you don't have to?
TurboSinceBirth
08-02-2011, 01:13 AM
The front just runs between the lower intake and the front valve cover. The rear is the only one that vents.
KPZVR4
08-03-2011, 08:15 PM
Is there an aftermarket hose type/style I can use, if so, what is it?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.