PDA

View Full Version : Aftermarket Radiator fitment



andyvr4
07-26-2011, 09:20 PM
While I've got everything else apart fixing the smoking issues I'm planning on swapping out radiators as well since the last radiator got damaged while it was out of the car for around 3 years :lo5l:.

I originally purchased a koyo 2" core radiator, but I just can't seem to make it fit with the stock fans and the stock intercooler hosing so I'm looking at other alternatives with smaller cores.

The primary one that I'm considering is the PWR since it's only 1.5" core and seems to be pretty well liked around here. The only concern that I have is if it'll clear the solid part of the intercooler piping that mounts right underneath the drivers side bracket for the radiator. Does anybody on here happen to have the PWR radiator with stock fans and the stock intercooler piping?

I've also considered the mitismoto since it's so much cheaper, but I'm a little worried about both the quality and the fitment because I've been reading a lot of threads were people have had problems with them not fitting!

andyvr4
07-27-2011, 04:24 PM
I just ordered the PWR radiator so I'll let you guys know how it works!

anyonebutme
07-27-2011, 04:58 PM
You need to either mod the stock upper brackets or get ones from Maximal or 3SX to fit the 2" cores like the Koyo and Mitsimoto. Easy to do, takes like 2 minutes to cut the rubber isolator and done. As for the IC piping, I just pushed on it and done.

andyvr4
07-27-2011, 05:25 PM
You need to either mod the stock upper brackets or get ones from Maximal or 3SX to fit the 2" cores like the Koyo and Mitsimoto. Easy to do, takes like 2 minutes to cut the rubber isolator and done. As for the IC piping, I just pushed on it and done.
The problem is the part of the IC piping that was an issue was the solid metal pipe running right around the drivers side front (short of changing the mounting brackets it doesn't flex)!

green-lantern
07-27-2011, 06:06 PM
Weird, I didn't have much trouble mounting my koyo. I had to grind the stud sticking out of the AC hose flange then popped it in. It was a bitch to use the stock mounts but like anyone said you can cut the rubber some and it fits pretty good. I don't remember any issues with the stock IC pipes.

SteveVR4
07-27-2011, 06:31 PM
Get the 3SX one. It fits properly and comes with mounting brackets to properly hold it in place and also uses the stock fans.

andyvr4
07-27-2011, 07:28 PM
Get the 3SX one. It fits properly and comes with mounting brackets to properly hold it in place and also uses the stock fans.
I actually just ordered a PWR this afternoon. From what I've read I think it should fit ok (or at least close enough that I can modify things to make it fit!

andyvr4
07-29-2011, 11:55 AM
Get the 3SX one. It fits properly and comes with mounting brackets to properly hold it in place and also uses the stock fans.

I just heard back from IPS and apparently they can no longer get the PWR since it's no longer shipped to the US, so which one of your radiators were you talking about? I've already tried a 2" Koyo that had major fitment issues with the stock intercooler system, so will yours fit different in this regard?


Also what have you guys heard about the mitsimoto radiators? I've several mixed replies where some people love them and others don't like them!

Does anybody on here have one with stock fans and the stock intercooler piping?

SteveVR4
07-29-2011, 01:43 PM
3SX Custom High-Capacity Single-Pass Radiator*-*Mitsubishi 3000GT*/*Dodge Stealth Parts (http://www.3sx.com/store/comersus_viewItemBundle.asp?idProduct=27300)

andyvr4
07-29-2011, 02:29 PM
3SX Custom High-Capacity Single-Pass Radiator*-*Mitsubishi 3000GT*/*Dodge Stealth Parts (http://www.3sx.com/store/comersus_viewItemBundle.asp?idProduct=27300)

So there aren't any fitment issues between the front A/C bolts and the stock intercooler piping with this one like what I had with the koyo?

green-lantern
07-29-2011, 04:20 PM
So there aren't any fitment issues between the front A/C bolts and the stock intercooler piping with this one like what I had with the koyo?

I'm pretty sure those require you to grind down that bolt/stud also. I think I remember a thread once where he said you did anyway. Pretty much with any larger radiator I think you do. I think that is the only thing you need to do though.

andyvr4
07-29-2011, 04:35 PM
I'm pretty sure those require you to grind down that bolt/stud also. I think I remember a thread once where he said you did anyway. Pretty much with any larger radiator I think you do. I think that is the only thing you need to do though.

What about the mishimoto, have you heard if you half to grind them down with it? I know it's only a 1.65" core vs the 2" of the 3sx and koyo. Maybe that extra .35" will make a difference :).

Valhallaz
07-29-2011, 05:49 PM
I can't say a bad thing about my Mishimoto. Fitment is as good as any I've seen. I think you're hit or miss on the bolt though. If I had the larger brackets, I'd be happy to throw them on to see if it hits in my 1st gen, but I've not seen a reason I'd want to spring for them. The strapping works just fine.
Wish I could be of more help. Good luck.

green-lantern
07-29-2011, 09:14 PM
What about the mishimoto, have you heard if you half to grind them down with it? I know it's only a 1.65" core vs the 2" of the 3sx and koyo. Maybe that extra .35" will make a difference :).

I haven't but if I need to grind cut one bolt to fit a bigger radiator it's not a bad trade off.

andyvr4
07-29-2011, 10:41 PM
I can't say a bad thing about my Mishimoto. Fitment is as good as any I've seen. I think you're hit or miss on the bolt though. If I had the larger brackets, I'd be happy to throw them on to see if it hits in my 1st gen, but I've not seen a reason I'd want to spring for them. The strapping works just fine.
Wish I could be of more help. Good luck.
Thanks, I went ahead and ordered a mishimoto, for the price I just don't think I'm going to be able to beat it and since I've already had problems with the 2" core koyo I'm really concerned to go with another 2" core radiator.


I haven't but if I need to grind cut one bolt to fit a bigger radiator it's not a bad trade off.
Yeah, if I half to I'll just grind it down, I just worry a little bit about damaging them! I don't want my A/C system to leak :).

andyvr4
08-07-2011, 11:31 PM
To update this thread, I ended up going with the mishimoto and it fits (just barely). I ended up using maximal's koyo brackets, but I had to cut a notch in them to get them to clear the hump in the middle of the mishimoto radiator as well as bend them slightly to get the bolt holes to line up, but when all said and done the radiator is extremely secure and I have around an 1/8th of inch of clearance between the radiator and the front bar of the car and around 1/4 inch of clearance between the stock fans and the intercooler piping!

green-lantern
08-08-2011, 07:24 AM
Good to know, thanks for the update.