rlataille
07-21-2011, 04:29 PM
got the calipers for $288 and rotors for $200 im currently working on fabbing up some plates. Trying to do a BBK on the cheap. If i get enough interest I can get a batch made so just pm me if you are interested I probably need 10-15 people to get this to happen if there is enough interest Ill get some pricing togeather and find someone to make them.
when I picked a brake setup initial and consumables costs where a large factor. a complete set of 14" gt500 brakes can be had for 900 new go used and you can get for <500 :-D. also replacement rotors are availible for <$300. The pad selection is vast and affordable because the gt500 shares pads with a few other sports cars.
The brakes and hubs are at the fabricators now and I anticipate having prototype of the adapters by next week.
http://i1191.photobucket.com/albums/z473/VR441/IMG024.jpg?t=1310695568
http://i1191.photobucket.com/albums/z473/VR441/IMG025.jpg?t=1310695651
http://i1191.photobucket.com/albums/z473/VR441/IMG026.jpg?t=1310695790
http://i1191.photobucket.com/albums/z473/VR441/IMG028.jpg?t=1310695936
USED A=P*R'2 to get 2% I do not anticipate but have considered that a porporioning valve could be nessacary, anouther option is a spyder porportioning valve (more rear bias) or an australian (split point may be too low) . other options if bias is not good would be to run less agressive pads in the front. do you know the piston area of your stoptechs??
STEALTH 316""
"The 3000GT VR4 and Stealth TT utilize a 4-wheel, 2-channel ABS braking system, as shown in the illustration below. The master cylinder contains two pistons which effectively divide the brake lines into two separate hydraulic systems. One system is the left-front and right-rear brakes, and the other is the right-front, left-rear brakes. This is done for safety in case a leak develops in one of these systems. These two hydraulic lines go from the master cylinder to the ABS hydraulic unit (HU). The HU controls the four output brake lines as two channels. One channel for each side of the car. However, because of the use of select-low valves between the two rear wheels and between two wheels on one channel (same side of car), a total of 3 wheels are controlled hydraulically at the same time. In order to prevent lock-up of the rear brakes during heavy braking, a proportioning valve is used on the two brake lines going from the HU to the rear brakes. For the hatchback AWD models, the output pressure will be the same as the input pressure until there is 533 to 604 psi pressure in the rear brake lines (called the split point). At pressures greater than this, the output pressure to the rear brakes will drop 34 to 42 percent. For the convertible AWD models, the split point is higher at 704 to 775 psi and the pressure drop is lower, 25 to 34 percent. The preceding is for North American and European models. The proportioning valve for vehicles bound for Australia was yet a third model. It had a split point in the range of 391 to 462 psi and a pressure drop of about 25 percent. "
http://i1191.photobucket.com/albums/z473/VR441/photo.jpg?t=1311034929
http://i1191.photobucket.com/albums/z473/VR441/ds.jpg?t=1311035071
http://i1191.photobucket.com/albums/z473/VR441/dc.jpg?t=1311035309
http://i1191.photobucket.com/albums/z473/VR441/cv.jpg?t=1311035356
http://i1191.photobucket.com/albums/z473/VR441/th_jpg.jpg
when I picked a brake setup initial and consumables costs where a large factor. a complete set of 14" gt500 brakes can be had for 900 new go used and you can get for <500 :-D. also replacement rotors are availible for <$300. The pad selection is vast and affordable because the gt500 shares pads with a few other sports cars.
The brakes and hubs are at the fabricators now and I anticipate having prototype of the adapters by next week.
http://i1191.photobucket.com/albums/z473/VR441/IMG024.jpg?t=1310695568
http://i1191.photobucket.com/albums/z473/VR441/IMG025.jpg?t=1310695651
http://i1191.photobucket.com/albums/z473/VR441/IMG026.jpg?t=1310695790
http://i1191.photobucket.com/albums/z473/VR441/IMG028.jpg?t=1310695936
USED A=P*R'2 to get 2% I do not anticipate but have considered that a porporioning valve could be nessacary, anouther option is a spyder porportioning valve (more rear bias) or an australian (split point may be too low) . other options if bias is not good would be to run less agressive pads in the front. do you know the piston area of your stoptechs??
STEALTH 316""
"The 3000GT VR4 and Stealth TT utilize a 4-wheel, 2-channel ABS braking system, as shown in the illustration below. The master cylinder contains two pistons which effectively divide the brake lines into two separate hydraulic systems. One system is the left-front and right-rear brakes, and the other is the right-front, left-rear brakes. This is done for safety in case a leak develops in one of these systems. These two hydraulic lines go from the master cylinder to the ABS hydraulic unit (HU). The HU controls the four output brake lines as two channels. One channel for each side of the car. However, because of the use of select-low valves between the two rear wheels and between two wheels on one channel (same side of car), a total of 3 wheels are controlled hydraulically at the same time. In order to prevent lock-up of the rear brakes during heavy braking, a proportioning valve is used on the two brake lines going from the HU to the rear brakes. For the hatchback AWD models, the output pressure will be the same as the input pressure until there is 533 to 604 psi pressure in the rear brake lines (called the split point). At pressures greater than this, the output pressure to the rear brakes will drop 34 to 42 percent. For the convertible AWD models, the split point is higher at 704 to 775 psi and the pressure drop is lower, 25 to 34 percent. The preceding is for North American and European models. The proportioning valve for vehicles bound for Australia was yet a third model. It had a split point in the range of 391 to 462 psi and a pressure drop of about 25 percent. "
http://i1191.photobucket.com/albums/z473/VR441/photo.jpg?t=1311034929
http://i1191.photobucket.com/albums/z473/VR441/ds.jpg?t=1311035071
http://i1191.photobucket.com/albums/z473/VR441/dc.jpg?t=1311035309
http://i1191.photobucket.com/albums/z473/VR441/cv.jpg?t=1311035356
http://i1191.photobucket.com/albums/z473/VR441/th_jpg.jpg