PDA

View Full Version : AWD Trans Rattle/Noise



DrGonzo
07-13-2011, 11:59 PM
So I have been prone to the notorious trans rattle. My first though was the throw out bearing. Picked up a brand new one swapped it out and the rattle is still there. At a local meet I spoke with Chris "Ninja Performance" and he said it sounded like the input shaft bearing. Made sense so I picked one up from GZP, dropped the trans again to swap out the bearing. Needless to say both the old throw out bearing and the old input shaft bearing looked fine when removed.

Guess what! the damn noise is still there...WTFH!!!!

So I am getting annoyed that I have dropped the trans twice and replaced to perfectly good parts and the damn noise is still there.

I have checked specs on all bolts, Flywheel was resurfaced and clutch is new OEM. It usually goes away when I push in the clutch which lead me to believe the throw out bearing.

So my question to everyone that has had this issue, how did you get it fixed??

Any other ideas what could cause the rattling noise?

HellBringer
07-14-2011, 09:10 AM
Fact of life - they all do it - accept it and move on. Some are louder than others, but every 5sp car I've owned has done it. I contribute it in part due to the lack of a pilot bearing on the input shaft. In some cases the noise is exacerbated by the clutch hub springs rattling around like a tambourine.

TwIzTeD_3kGt
07-14-2011, 09:14 AM
I think it was Ray or Matt who found the center hub of the stock clutch rattles.

What clutch you running?

DocWalt
07-14-2011, 10:11 AM
I think nearly every Getrag rattles. Mine was really loud at times, and other times it was nearly silent. Tried a lot of different fluids, but I ended up back with the MTL/MT90 mix (MT85 replaces the mix)

Ray Pampena
07-14-2011, 10:14 AM
yea most of the noise is from the clutch disk hub. it rattles inside the disk. there used to be a tsb on it when i worked for mitsu. ive noticed some clutches do it way more than others

Chris@Rvengeperformance
07-14-2011, 12:47 PM
it is odd, but of all the issues I have with my trans it doesn't rattle at all. I'm a little worried to rebuild it.

DrGonzo
07-14-2011, 01:34 PM
I'm running just an Exedy OEM replacement clutch right now. Never had issue with them in any of the other cars I installed them in.

So far is sounds like the consensus is that it has something to do with the clutch disk so I'll go with that "especially knowing Ray and Matt looked into it" I was just worried it is something internally with the trans. I'm in no place to do a trans rebuild at this time...LOL

Thanks everyone!! :)

TwIzTeD_3kGt
07-15-2011, 12:16 AM
I had a rattle up until last week, it stopped when I went to the track.

http://i39.photobucket.com/albums/e200/twizted_3kgt/2011-07-07_21-09-54_108.jpg

After I noticed I couldn't drive anymore, I noticed "Hey! No more rattle!" :)

Hans@GZP
07-15-2011, 02:02 PM
Must be SPEC.

TwIzTeD_3kGt
07-15-2011, 07:31 PM
Must be SPEC.

You got it. 4+. Had the disc rebuilt, original rivets for the pads were too small, and the center hub wasn't centered. Quality.

enigma
07-17-2011, 12:17 PM
I spoke to Frank at Koemex quite a few years ago about the Getrag rattle and its main cause is the size of the gears especially in the 5 sp boxes they are quite large and tend to knock meshing together when hot, mine has done this from day 1 but it can be stopped on some boxes by increasing/decreasing idle speed.