View Full Version : 5spd vs 6spd shifter cables
Emilie@GZP
07-06-2011, 06:47 PM
How do you tell the difference, if you have two sets of shifter cables sitting in front of you?
ALL 5spd shifter cables are the same, turbo or non turbo, they all pop the same part number. 6spd's have their very own cables... lucky them. and ALL 93+ shift levers are the same.
So... looking at 2 sets of shifter cables, with 93+ shift levers... how do you tell which is a 6spd, and which is a 5spd?
The 6spd shifter cables have a white band on each cable, the 5spd cables have a pink band.
http://i34.photobucket.com/albums/d111/3Scar/IMAG0292.jpg
http://i34.photobucket.com/albums/d111/3Scar/IMAG0293.jpg
AdamVR4
07-06-2011, 07:03 PM
Handy little nugget.
Emilie@GZP
07-06-2011, 07:09 PM
It's my helpful hint for the day :)
93STLTH
07-06-2011, 07:49 PM
Nice sig Em.
aaronatstate
07-06-2011, 08:00 PM
So why is there a difference?
Gearheadvr4
07-06-2011, 08:08 PM
Sixth gear and especially reverse are pretty far over compared to the five speed. The cables needed changed to accommodate the trans. They changed the base of the shifter too. The differences are so subtle that I had a very hard time figuring this out. I had 3 sets and couldn't initially pick out the six speed.
Nice tip!!
Emilie@GZP
07-06-2011, 08:09 PM
Stealth 316 - 5-spd to 6-spd AWD Conversion (http://www.stealth316.com/2-5spdto6spd.htm)
5-speed cables may not allow enough travel however some people (See Neil's post to the 3SI messsage board below for example) have been able to re-use the 5-speed cables.
I really do not know WHAT the difference is, only that there is one. The above link is about the only information I've found on the differences between the cables.
I know that's not really a very helpful answer, but it's what I've got. I will look into it a little more tomorrow if I can. I pulled the cables out for a customer who needed them, but found another 6spd set in a pile. I'll mess with them a little tomorrow and see if I can figure out what the difference is.
Emilie@GZP
07-06-2011, 08:10 PM
Sixth gear and reverse. The cables needed changed to accommodate the trans. They changed the base of the shifter too. The differences are so subtle that I had a very hard time figuring this out. I had 3 sets and couldn't initially pick out the six speed.
Nice tip!!
From what I could tell, the shifter only changed from 91/92 to 93+, as per the part numbers and digging I've done around the shop. It was not a 5spd/6spd or change, more a year change... as the shifters on the 93+ non turbos are the same as well.
so can the 6-speed shift cable be used on 5-speeds?
Emilie@GZP
07-06-2011, 11:47 PM
I have no idea why you would want to
AdamVR4
07-07-2011, 12:36 AM
From what I could tell, the shifter only changed from 91/92 to 93+, as per the part numbers and digging I've done around the shop. It was not a 5spd/6spd or change, more a year change... as the shifters on the 93+ non turbos are the same as well.
Just another reminder that '93 was the best year. $700 t-case housing and it's got everything the 6 speed has and better pistons :)
FastOldGuy
07-07-2011, 01:06 AM
93 with SS TC Housing FTW
Emilie@GZP
07-07-2011, 11:05 AM
Just another reminder that '93 was the best year. $700 t-case housing and it's got everything the 6 speed has and better pistons :)
it's more the crankshaft and 4 bolt main that was better.... not really so much the difference in pistons...
AdamVR4
07-07-2011, 11:47 AM
it's more the crankshaft and 4 bolt main that was better.... not really so much the difference in pistons...
Reread what I said, replacing 6 speed with 2G ;)
The '93 has every good thing from both generations...
Best things about 1G's: 5 spd trans, pistons with thicker upper ring lands
Best things about 2G's: shorter shifter, stronger main t-case housing, 4 bolt, forged crank
Emilie@GZP
07-07-2011, 11:56 AM
I thought all the engine internals (pistons, blah de blah) changed with the 2-bolt/4-bolt....?
AdamVR4
07-07-2011, 12:33 PM
I can't find the exact post where Matt Monett lays it all out, but he says here that 91-93 pistons are stronger...
http://www.3si.org/forum/f35/how-good-mitsu-pistons-rings-213309/index2.html
*gasp* you mean the 95-96 tt's aren't the best 3/s's? :suspect:
Emilie@GZP
07-07-2011, 12:59 PM
According to ASA, 91-92 pistons are the same, and 93+ pistons are the same (part number). Looks like the change happened with the 4 bolt.
Emilie@GZP
07-07-2011, 01:05 PM
true, but no motor can take detonation, if you get bad detonation and don’t brake pistons you will hammer the rod bearings and thy will spin. The best thing to do is to keep away detonation. Back in my Blown mustang racing days, the rool of thumb was if you got detonation you could here, it was time to pull the pan and put in new rod bearings.
here is also a little known tid bit... the 91-93 pistons have a MUCH thicker top ring land then the 94-up pistons.
so if you buy a short block for a 94-up car get the short block part # for the 93 vr-4 (there are 3 parts #'s 91-92, 93, and 94 up)
not very often do 91-93 cars brake pistons, ever wonder why?
The bolded part is true... HOWEVER, there are revised part numbers that show that 93 is the same part as 94+
AdamVR4
07-07-2011, 01:13 PM
I have no idea what ASA is, I can't take the time to decipher that chart... I guess I'll just have to bump this thread if my engine ever fails and I get a chance to measure the thickness :)
So just to be clear, in your opinion, Matt Monett was spreading misinformation for years and years?
Emilie@GZP
07-07-2011, 01:27 PM
ASA... Mitsubishi CAPS. The year rangers are the 2 left columns (production dates). part numbers are 4th column. red part numbers are the revised part numbers. the 93 model year (92.6-93.5) part numbers for the STD piston size is the same as the 93/6+ production year.
Emilie@GZP
07-07-2011, 01:32 PM
I have no idea what ASA is, I can't take the time to decipher that chart... I guess I'll just have to bump this thread if my engine ever fails and I get a chance to measure the thickness :)
So just to be clear, in your opinion, Matt Monett was spreading misinformation for years and years?
Piston Part Numbers Highlighted
AdamVR4
07-07-2011, 01:59 PM
So when were the part numbers revised? Is there a chance this is a relatively recent revision?
Emilie@GZP
07-07-2011, 02:02 PM
That, I don't know.
Emilie@GZP
07-07-2011, 02:06 PM
So when were the part numbers revised? Is there a chance this is a relatively recent revision?
Just spoke with mitsu, they just change the part numbers either due to revisions, or whatever, over the years. funny enough, the part number for the 91-92 pistons, is now revised to the 93+ (originally 94+) part number....
Chris@Rvengeperformance
07-07-2011, 03:11 PM
The later pistons had thinner ringlands due to emissions requirements.
Either piston would work for a rebuild, so mitsu probably stopped making the early pistons a long time ago and changed the part # when they ran out.
Sent from my DROIDX using Tapatalk
AdamVR4
07-07-2011, 03:13 PM
The later pistons had thinner ringlands due to emissions requirements.
?? Somebody make the connection for me, haha...
aaronatstate
07-07-2011, 07:18 PM
?? Somebody make the connection for me, haha...
I missed it too...
Chris@Rvengeperformance
07-07-2011, 09:28 PM
I missed it too...
here some general piston info from another site:
"With Hypereutectic pistons, the primary reason for having all of this free silicon is to reduce piston ring groove wear. This allows piston designers to move the top compression ring much farther up the side of the piston (where combustion temperatures are much hotter), and run much smaller, thinner piston ring lands (the metal section separating the ring grooves). The reason piston designers want to do this is that it allows a lighter piston to be produced, and also has dramatic results in changing engine emission characteristics. As emission laws become tougher, it will be commonplace to find true Hypereutectic pistons in road engines."
Forged or Cast?* Piston Basics! (http://www.hoon.tk/tech_tips/pistons.html)
Chris@Rvengeperformance
08-12-2012, 11:54 PM
FYI 6 speed shifter cables won't fit the five speed. The outer cable is too short:
4451
J_Parker
08-13-2012, 04:32 PM
My question being... Can the five speed cables be used on the six speed trans??? I'm thinking of picking up a 6 and really don't want to go through the hassle of hunting down cables, which I've found to be impossible to find.
green-lantern
08-13-2012, 05:14 PM
My question being... Can the five speed cables be used on the six speed trans??? I'm thinking of picking up a 6 and really don't want to go through the hassle of hunting down cables, which I've found to be impossible to find.
From what I understand it will trash your synchros. You know you need to change the rear diff and all that right?
Edit: BTW hans has cables
TurboSinceBirth
08-13-2012, 10:50 PM
My question being... Can the five speed cables be used on the six speed trans??? I'm thinking of picking up a 6 and really don't want to go through the hassle of hunting down cables, which I've found to be impossible to find.
Depending on how soon you need the 6-speed shifter cables I will be selling mine when I swap my 5-speed in. I have two sets of 5-speed shifter cables.
GTOJOE
08-14-2012, 08:31 AM
I heard one of the guys on the NZ forum say he fitted a complete 6 speed setup to his 5 speed. cables and shifter & base assembly.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.