View Full Version : ECU/TB rebuilds
BaadVR4
06-30-2011, 08:15 PM
I am in need of a reliable source for both ECU and Throttle Body rebuilds. I have one 92 TT ECU and probably 3 TT TBs I need rebuilt. Anybody here do either?
Thanks,
Milt
dbest671
06-30-2011, 08:36 PM
The throttle body rebuild really isn't that difficult. All you need is an impact driver, new(ish) #2 screwdriver, and some locktite. You can get the seals from Mach V motorsports, and the rest is gravy. Just make sure to mark the position of the TPS sensor before you pull it off.
I have done two so far, the first one was a PITA because I stripped the throttle plate screw and had to drill it out. Hence why I said a newish #2 screwdriver.
BaadVR4
06-30-2011, 08:59 PM
Easy for you to say. One of the TBs has had the throttle plate return screw moved. How do I reset it? What about the BISS? About the only thing I can do for sure is set the TPS. It's extremely easy if you have an AEM. Just plug the TPS in, connect your laptop, then set the TPS with the throttle held wide open, moving the TPS until the the AEM read out changes from red to clear (usually about 98%), then check the closed position (with the .065" feeler gauge inserted per the manual) reads zero. Works great, no need to try to keep multi-meter leads on terminals/etc/etc. Maybe you would do my TBs? For the low low? If you do the basics, I'll do the TPS. LMK. Thanks,
Milt
The throttle body rebuild really isn't that difficult. All you need is an impact driver, new(ish) #2 screwdriver, and some locktite. You can get the seals from Mach V motorsports, and the rest is gravy. Just make sure to mark the position of the TPS sensor before you pull it off.
I have done two so far, the first one was a PITA because I stripped the throttle plate screw and had to drill it out. Hence why I said a newish #2 screwdriver.
dbest671
06-30-2011, 09:18 PM
^Oh I didn't realize it was that bad... I thought you just wanted the seals replaced. On all my throttle bodies, I was very careful to mark everything if it had to be removed. I know there is something on how to adjust the throttle plate return screw, I'll search through the manual to see if I can find the procedure.
BaadVR4
06-30-2011, 09:39 PM
That would be greatly appreciated. If I had that and the shaft/BISS seals, I might attempt to rebuild them on my own. Thanks,
Milt
^Oh I didn't realize it was that bad... I thought you just wanted the seals replaced. On all my throttle bodies, I was very careful to mark everything if it had to be removed. I know there is something on how to adjust the throttle plate return screw, I'll search through the manual to see if I can find the procedure.
dbest671
06-30-2011, 09:55 PM
Found a link without sending you over to the other site Throttle Body Rebuild (http://jns.jimnshar.com/id40.htm)
Throttle body seals can be bought here Throttle Body Seals (http://www.machv.com/throtbodseal.html)
I ordered the biss screw, o-ring, and plug from Cherry Hill. If you remove the FIAV, you will probably want to replace that gasket as well.
Jimvr4
07-01-2011, 01:23 AM
That's the best writeup on TB rebuilds I've seen ;) What is the part number for the BISS screw and O-Ring? I'd like to add them to my write-up.
Jim :)
BaadVR4
07-01-2011, 08:20 PM
Thank you very much!!!!!!!!!!!!!!!!!!!
Found a link without sending you over to the other site Throttle Body Rebuild (http://jns.jimnshar.com/id40.htm)
Throttle body seals can be bought here Throttle Body Seals (http://www.machv.com/throtbodseal.html)
I ordered the biss screw, o-ring, and plug from Cherry Hill. If you remove the FIAV, you will probably want to replace that gasket as well.
dbest671
07-01-2011, 08:33 PM
That's the best writeup on TB rebuilds I've seen ;) What is the part number for the BISS screw and O-Ring? I'd like to add them to my write-up.
Jim :)
Here are all the gaskets that will be needed if you completely disassemble the TB... But you really don't need to remove the ISC, FIAV, or Biss screw to replace the shaft seals.
MD608806 - Biss o-ring
MD614948 - Biss screw
MD614532 - Biss cap- most people are actually missing this little plug/cap
MD614417 - ISC/IAC o-ring
MD614406 - FIAV gasket
Jimvr4
07-02-2011, 02:42 AM
How DO you find these part numbers? I looked all over CAPS and never found them
green-lantern
07-02-2011, 03:03 AM
Great links April, Thanks a bunch
BTW, I plan to have a get together pretty soon so LMK if you and Don want to come.
dbest671
07-02-2011, 01:18 PM
How DO you find these part numbers? I looked all over CAPS and never found them
CAPS is for children, you need to upgrade to ASA :p... all seriousness, ASA is better than CAPS. But I can pull the part numbers in CAPS also. If I have a general idea on what to look for, I can pretty much find it if it's in the program.
http://i392.photobucket.com/albums/pp4/hoopb23/Throttlebodyinner.jpg
Great links April, Thanks a bunch
BTW, I plan to have a get together pretty soon so LMK if you and Don want to come.
Yeah just let us know the time/date, how many people are left? I seems there are more people in Nashville too, I can spread the word.
green-lantern
07-02-2011, 03:37 PM
Yeah just let us know the time/date, how many people are left? I seems there are more people in Nashville too, I can spread the word.
Still plenty of people around. Just not all in one place on the internets. I might wait a bit longer so Sean and Linda can get around better.
green-lantern
11-01-2011, 10:32 PM
Well I have my TB apart but the old seals just pretty much fell out. The new ones have metal but it doesn't appear the old ones did. Did the old ones not have metal but new seals do? My TB is probably an NA TB BTW, not a turbo model. Not sure if the seals were different in the NA ones or not.
dbest671
11-01-2011, 11:39 PM
^Seals should be the same *I think*. Actually I believe they are because I took apart a N/A. Maybe somebody already replaced the seals with regular o-rings. All the ones I have taken apart have had the metal in the seal.
RealMcCoy
11-02-2011, 12:01 AM
I'll add a couple tips that will greatly help the chances of a successful repair:
The screws are staked on the back side... In addition to having a screwdriver that is in good condition and a proper fit, grind the staked area back to the shaft with a die grinder or dremel.
The original seals had no rubber outer surface, it was a plain metal seal with the rubber inner lip. The new seals have an outer rubber surface that is easily torn up on install. You can prevent this by taking a large drill bit (I usually just grab the 1/2" bit, it's the largest in my set) and turning it by hand lightly to create a chamfer at the entry point for the seal.
green-lantern
11-02-2011, 08:44 AM
^Seals should be the same *I think*. Actually I believe they are because I took apart a N/A. Maybe somebody already replaced the seals with regular o-rings. All the ones I have taken apart have had the metal in the seal.
That's odd, I've looked and looked and there isn't any metal. Somebody must have put some crappy seals in it at one time. They aren't regular O rings, they sort of look like the new ones but no metal outer rings. Also it already has the plastic bis screw in it so I'm not sure what year they went plastic (This should be 95-96 TB) but it might have been replaced also.
Roybatty
11-02-2011, 10:01 AM
That's odd, I've looked and looked and there isn't any metal. Somebody must have put some crappy seals in it at one time. They aren't regular O rings, they sort of look like the new ones but no metal outer rings. Also it already has the plastic bis screw in it so I'm not sure what year they went plastic (This should be 95-96 TB) but it might have been replaced also.
I used one of the write ups on this a while ago. I remember using some fatter O-rings from Home Depot (as opposed to OEM/Viton, metal backed)for a snug fit; seems fine after a number of years. The other important issue was using loctite on the screws on the throttle plate.
green-lantern
11-02-2011, 07:09 PM
http://www.streettunedmotorsports.com/parts/a/milspec_evo_throttle_body_shaft_seals.jpg
My seals are like this. Since the ones that came out don't have the metal can you tell me what end goes in 1st? Metal side or rubber goes in 1st?
dbest671
11-02-2011, 07:40 PM
Where did you get yours? I got mine from machV motorsports, and they didn't exactly look like that.
green-lantern
11-02-2011, 08:16 PM
STM, somebody recommended them to me.
I sent him a PM so maybe he will chime in.
green-lantern
11-02-2011, 08:23 PM
STM: MIL.SPEC THROTTLE BODY SHAFT SEALS | EVO VIII-IX | 91-99 DSM | 91-99 3000GT (http://www.streettunedmotorsports.com/parts/milspec_evo_throttle_body_shaft_seals.htm)
Austin@STM
11-02-2011, 08:39 PM
the rounded side goes to the outside of the throttle body. The other side faces in so that when there is positive pressure it pushes the "flap" against the shaft to form a better and better seal as you add pressure. If you put them on backwards it will just blow air through them at a certain point.
I usually just use the back side of a socket and a hammer to put them in place, just make sure you take your time and hit it in evenly until it is just inside of the throttle body. Then make sure you thoroughly clean the shaft and use a little assembly lube or motor oil on it where it will contact the shaft.
Final step that i cant stress enough is make sure you loctite the 2 screws that hold in the butterfly, i've read to many threads where those bolts back out on people and their motors get destroyed.
dbest671
11-02-2011, 09:05 PM
Shit, I wish I got those now... but I didn't know about STM when I rebuilt my throttle bodies. I used loctite red when I reassembled my throttle body, and make sure you don't put the throttle plate in backwards.
green-lantern
11-02-2011, 09:07 PM
the rounded side goes to the outside of the throttle body. The other side faces in so that when there is positive pressure it pushes the "flap" against the shaft to form a better and better seal as you add pressure. If you put them on backwards it will just blow air through them at a certain point.
I usually just use the back side of a socket and a hammer to put them in place, just make sure you take your time and hit it in evenly until it is just inside of the throttle body. Then make sure you thoroughly clean the shaft and use a little assembly lube or motor oil on it where it will contact the shaft.
Final step that i cant stress enough is make sure you loctite the 2 screws that hold in the butterfly, i've read to many threads where those bolts back out on people and their motors get destroyed.
Thanks a bunch my friend, don't worry, no way in hell those screws go in without locktight. I might just center punch them too (nobody try that without resting the screw heads against something solid BTW).
RealMcCoy
11-03-2011, 12:22 AM
Easy for you to say. One of the TBs has had the throttle plate return screw moved. How do I reset it?
That is the fixed SAS adjustment covered on page 13A-59 of the manual.
BaadVR4
11-03-2011, 07:30 AM
Thank you. I "knew" it had to be somewhere, I just didn't know where to look. Thanks to you, I now have. I might even have enough info now to take a stab at rebuilding one on my own. I'm certain if I could just watch someone do one right I could do it, too. It's just that uncertainty of never having seen it done before. Again, Thanks,
Milt
That is the fixed SAS adjustment covered on page 13A-59 of the manual.
milt, did you ever find an ECU rebuilder?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.