View Full Version : Im a glutton for punishment...
JasonY
06-29-2011, 09:47 PM
Well, listing my entire pile of performance mods up for sale that are currently on the car...
WTF am i doing that for?
IPS Single setup, air/water IC sitting in the location where the battery is, a/w IC i have picked out is rated for 1200hp, should be good. Heat exchanger will go where the stock a/c core is with a pair of pusher fans to cool it which of course will sit in front of the pushers for the radiator, got fans?:lo5l:
The plan is absolute simplicity, see the two pics below:
Trevors install:
http://members.cox.net/trevorlj2/65.jpg
Now just turn his turbo outlet 180* roughly and have it feet directly into an air/water like this:
http://www.siliconeintakes.com//images/product/intercooler_type15_picture.jpg
That setup will feed directly into DR's intake manifold and Q45 or equivalent throttle body. Should have 3 couplers max and around a foot to 18" of IC piping:)
Battery should be able to lay flat under the A/W IC, another will see how it goes while in progress.
Turbo is up in the air ATM im looking at a Comp Turbo oil-less Billit 6765, should light quick, about the same compressor as the garret 4094 but with a 65mm turbine vs the 77mm in the 4094. Should breathe well on a 3L engine.
Going with a divided T4 turbine unsure of the a/r as of now, with that small of a turbine wheel i may go 1.XX to let it breathe up top. Using a 4" V-band exhaust outlet so the frame work(downpipe) is already setup for a bigger turbo is this one proves too small, but all input is welcome on what turbo to use!
Going to breathe into the 4" titanium exhaust that i had IPS make for me forever ago, so 4" from the turbo right the fuck out the back of the car:DevilSmile:
Should be really fun to build and be quite unique and make some rrreally fun noises:)
Anyway thats whats going on with my junk. Damn the NG and Von with the bad thoughts they left in my head...:lo5l:
Jason
Broomfield Racing
06-29-2011, 10:02 PM
:jawdrop:
Greg E
06-29-2011, 10:06 PM
Give me your turbos!!! I'm dead serious. I need them this weekend.
green-lantern
06-29-2011, 10:14 PM
WTF am i doing that for?
The plan is absolute simplicity
Jason
I must disagree lol, I really don't see much simplicity with that setup. I do see awesomeness though.......
Nationalmilkman
06-29-2011, 10:19 PM
Should replace those front struts on the '99 first! Lol. Sick build though. Von just showed all of use that the weak link is the driveshaft!!
lawdogg
06-29-2011, 10:32 PM
So you were serious about it. SWEET! Can't wait until it's in.
JasonY
06-29-2011, 10:36 PM
LOL, yeah the suspension will be address accordingly when the car comes apart.]
Im probably gonna keep the stock DS for a bit since well, it doesnt break and it costs exactly 1200 less than a CF one does..lol
The only thing complicated about this setup is adding the water pump and making the 92mm ARC2 mas fit down in the bumper where the intake is on the setup. Might have to extend the harness or figure out where to run it through on the passenger side on the firewall.
Otherwise its way more than half as complicated as any current twin setup, no oil lines ftw. Just two coolant lines and cap everything else!
I enjoy building these things more than using them. The 99 is just sitting under a cover right now and i have little intention of using it anytime soon...
Jason
Greg E
06-29-2011, 10:40 PM
The only thing complicated about this setup is adding the water pump and making the 92mm ARC2 mas fit down in the bumper where the intake is on the setup. Might have to extend the harness or figure out where to run it through on the passenger side on the firewall.
Been a while but I remember the ARC comes with it's own MAF harness that you splice into the ECU. Should be more than enough wire to route it all the way down there. Have it follow the wiring for the ABS pump behind the fenders. Poke a hole in the rubber cover to route it into the cab.
JasonY
06-29-2011, 10:41 PM
OH! the Evo MAF is round isnt it? How to add 3ft to the stock harness???
edit: but its only 3" dia. the inlet on the turbo is 4"...lol Not sure that would be good to have the smaller Evo MAF.
Jason
Greg E
06-29-2011, 10:54 PM
OH! the Evo MAF is round isnt it? How to add 3ft to the stock harness???
edit: but its only 3" dia. the inlet on the turbo is 4"...lol Not sure that would be good to have the smaller Evo MAF.
Jason
Extending the stock MAF connector harness is easy. You just need some shrink tubing, solder and wires.
Mellon made 700AWHP with the stock EVO MAF in his 05 EVO. Just sayin...
Although, if I remember correctly, he had to keep regluing the thing back together because the turbo kept trying to eat it.
AdamVR4
06-29-2011, 11:02 PM
Nice, I love the Von-spot for the liquid-air. Have you decided on the core? Is the vendor supplying you any actually useful data? The engineer in me insists on modeling the system before I buy anything.
That's an absolute pipe dream set-up by the way :D
JasonY
06-29-2011, 11:04 PM
Yeah, i know it can move the air, im just wondering it necking the intake down that small would be a problem. but its not like a 67mm is a *big* turbo anyway...could probably go bigger w/o hurting anything...
Right now Adam, everything is in the research/planning stage. Im game for any/all info anyone wants to share! This is way more fun to me then even using the car...im such a dork..lol
I need a weekend to tear into the car and start actually figuring what and where things could actually fit in regards to the IC setup.
But yes, this is very similar to Vons car, only so many ways to fit something under the hoods of these cars!
Jason
AdamVR4
06-29-2011, 11:24 PM
Totally agreed with you about using the stock DS. It seems like you see 10 CFDS failures per every stock DS failure... And the stockers don't vibrate, heh.
Yeah, i know it can move the air, im just wondering it necking the intake down that small would be a problem.
Necking the intake where? Through the IC core?
Ideally the core manufacturer can give you pressure drop vs flow rate for both the air passages and water passages... Heat dissipated vs flow rate would make life a lot easier too :p
If they don't you can still model it but you'd need all the internal core dimensions and a lot more time :)
JasonY
06-29-2011, 11:38 PM
Id have the MAF in draw through, the 92mm arc2 one just happens to be close to the same size the same size(3.6"I.D.) as the 4" intake setup instead of flaring down to 3" then back to 4" with the Evo MAF.
Jason
futurevr4man
06-30-2011, 09:16 AM
its funny, i went to NG11 too and got crazy ideas in my head as well.
looks like fun, keep us updated.
HilbillyHomeboy
06-30-2011, 09:52 AM
Sounds like a helluva plan Jason! :cool:
Jeremy
TT Eric
06-30-2011, 10:21 AM
I'm more suprised by you getting rid of the A/C! :O
Eric
mb7050
06-30-2011, 10:53 AM
Sweet plan !!! Anxious to see how this comes together
AdamVR4
06-30-2011, 11:27 AM
I'm more suprised by you getting rid of the A/C! :O
Eric
I thought IPS found a way to make the downpipe so that the AC compressor could stay? No?
oohnoo
06-30-2011, 11:46 AM
That's gonna be badass.
I've been wanting to do a W/A setup for quite some time now. They can't be beat as most of them have a .1 pressure drop, yes that's a POINT ONE! One thing to remember though is even though it's being cooled with it's own radiator it's still in the engine bay and will heat soak, something you may want to read up on and look into.
For that reason I was going to put mine outside the engine bay. But for me it would be easy as I'm running two turbo's with complex piping vers your single, simple pipe routing.
Best of luck in the new build as I'm sure it'll be killer
I did see some pics of the NG and one motor had a W/M like your describing sitting where the battery is. Any more info on it?
i3igpete
06-30-2011, 11:49 AM
wait... oil less turbo!
futurevr4man
06-30-2011, 01:31 PM
That's gonna be badass.
I've been wanting to do a W/A setup for quite some time now. They can't be beat as most of them have a .1 pressure drop, yes that's a POINT ONE! One thing to remember though is even though it's being cooled with it's own radiator it's still in the engine bay and will heat soak, something you may want to read up on and look into.
For that reason I was going to put mine outside the engine bay. But for me it would be easy as I'm running two turbo's with complex piping vers your single, simple pipe routing.
Best of luck in the new build as I'm sure it'll be killer
I did see some pics of the NG and one motor had a W/M like your describing sitting where the battery is. Any more info on it?
bob-o, thats von's car (xwire). he has a huge single on it and water/air cooler. very well done, very clean car. im sure jason talked to him heavily as thats who he is mimicking
TT Eric
06-30-2011, 04:40 PM
I thought IPS found a way to make the downpipe so that the AC compressor could stay? No?
I said that because Jason said he would put the heat exchanger where the stock A/C core is, so I guess he's deleting it!
Eric
oohnoo
06-30-2011, 04:51 PM
You can easily just put it in front of the ac core like a front mount as it won't be as restrictive cause they're only an 1" thick, some are 2". But unless like you said the downpipe gets in the way of the compressor then that's another story.
Broomfield Racing
06-30-2011, 05:20 PM
wait... oil less turbo!
My thoughts exactly!
mb7050
06-30-2011, 05:39 PM
I had this core laying around and mayby tomorrow I´m going to take few things out and test if it really fits in there
http://img51.imageshack.us/img51/2852/imag0280j.jpg
http://img848.imageshack.us/img848/1864/imag0281h.jpg
http://img832.imageshack.us/img832/1338/imag0282i.jpg
http://img692.imageshack.us/img692/7496/imag0283nw.jpg
http://img30.imageshack.us/img30/5772/imag0284t.jpg
http://img24.imageshack.us/img24/565/imag0285w.jpg
http://img849.imageshack.us/img849/5088/imag0286k.jpg
the core is 12"x10"x4.75" and 3.5" in/out
19.5"x13"x4.75" overall
Its a huge core but I took a better look at it and looks like it should fit in there, inlet need to be rotated for sure etc etc..
roughly something like this
http://img39.imageshack.us/img39/1239/imag0286f.jpg
single makes sense with this setup but it doesnt have to be right ?
http://img692.imageshack.us/img692/5817/imag0288y.jpg
http://img9.imageshack.us/img9/761/imag0289y.jpg
JasonY
06-30-2011, 08:23 PM
Yeah about the A/C i was thinking about just how many times ive actually used it....never...:shrug: I guess i made a bigger deal out of keeping it then really necessary.
For primary cooling of the engine i am unsure on what fans yet, i dont know if i can keep the stock a/c fan on the drivers side or not. Like i was saying before, many of the smaller details will be fitted as it goes since i can only plan it so far ahead.
As for turbo choices, the 6765 lights quick as shit on the Supra's just seems to be pegged out on regular gas in the lower 700's so i may go to a 71mm turbo or just get the biggest a/r on the 67 to help it breathe up top. The whole idea of going bigger is to make about 600awhp at lower boost than needed by the 750's(25psi) so there is less heat produced and more overhead on pump fuel power wise instead of being RIGHT on the edge of knock with 93/1kcc's meth.
Hopefully i can get my hands on the big parts soon so i can start figuring out the little shit. The big investment is the manifolds and turbo thats gonna be around 5k for the pair, but fortunately everything from there on out is one smaller piece at a time which is much easier to live with financially.
And about the oil-less turbos, the company is called comp turbos and they use a greased ceramic bearing setup that only needs servicing every 50k miles of use which from what ive read is also only about 150 bucks to have done. They require coolant lines only and are based off PTE turbos, so if PTE offers it, Comp offers it with their bearing package.
Jason
familyMAN
06-30-2011, 08:43 PM
I may have missed it, buy who is fabbing the single setup for you?
JasonY
06-30-2011, 08:47 PM
I am buying an IPS kit since i dont have the time to fab a whole setup...
Also just got off the phone with CT and all their smaller frame turbos are available oil-less, anything up to an 80mm wheel.
Jason
JasonY
06-30-2011, 09:39 PM
heres the webpage explaining the turbos.
Turbochargers Comp Turbo - Oil-Less (http://www.compturbo.com/spotlights/oilless)
Jason
DocWalt
07-01-2011, 10:28 AM
This build is going to be sick!
Good to know they "incented" the oil-less turbos :p
AdamVR4
07-01-2011, 11:44 AM
I would try to keep the AC in a '99. You sure about this?
JasonY
07-01-2011, 01:02 PM
I've thought a lot about the a/c and really decided I don't need it. I never use it and if the car goes any real distance it does so on a trailer...so yeah as nice as it would be to keep I can't see the sense is paying for a entire redesign of the front manifold to keep something I don't use...
Jason
anyonebutme
07-01-2011, 06:21 PM
It better be done before next year's NG. If I have to bring the Banzai Bimmer next year I want someone to play around with, lol.
JasonY
07-02-2011, 11:46 AM
It will be done before NG next year, should be running again this year, trying to avoid prolonged downtime anymore with the car.
Denso does make an electric a/c compressor...:suspect:
Jason
JasonY
07-06-2011, 07:49 PM
Manifolds are getting dropped off at the coaters tomorrow:DevilSmile:
:runaway:
Jason
TT Eric
07-07-2011, 10:01 PM
Hehe! :bigthumb:
Eric
GTO Assassin
07-07-2011, 10:13 PM
You're not going stand alone?
Scotty
JasonY
07-07-2011, 10:16 PM
I am, it came stock on my car:) gonna use an ARC2 as the MAF upgrade until we figure out how to run MAP with the stock ECU.
Jason
J-Groove
07-08-2011, 12:21 AM
WOW!!
-John
JasonY
07-08-2011, 05:00 PM
Disassembly begins tomorrow! Excited and sad all at the same time.
:runaway:
Jason
AdamVR4
07-08-2011, 05:04 PM
sad
What? If you're feeling that emotion at all, abort now.
JasonY
07-08-2011, 05:09 PM
Not in that way, the car bores me to tears even with the fuel system in the car(500awhp is slow) but normally i take the car apart in the winter, but every time i do it stays apart forever since i NEVER hvae time to work on it then. So losing the car for the end of summer is what im bummed about.
But if i dont get most of the work done now while work is slow(comparatively) it'll never be finished since i wont have time to even look at the car from xmas to memorial day.
Jason
i3igpete
07-08-2011, 05:32 PM
just leave it with the 19Ts and go have fun with it on the track!
JasonY
07-08-2011, 05:37 PM
I'd have been fine with 19T's until i drove a DR750 car then my car felt like an inadequate turd.
I was planning on doing the 750's but at the same time ive always been endlessly frustrated with how cobbled together everything gets while still running twins. So im trying to cut down on the mess while doing something ive always wanted to do with the car mainly because its different and will be fun to build. I also dont want to do DR750's since ive already built a car with them and know exactly what they can do and always have access to that car, for me it would be like having two identical cars. *yawn*
Jason
green-lantern
07-08-2011, 06:49 PM
heres the webpage explaining the turbos.
Turbochargers Comp Turbo - Oil-Less (http://www.compturbo.com/spotlights/oilless)
Jason
Somebody posted these up a while back. I can't remember if it was on this site or the other but I remember being pissed because I just bought turbos. :lo5l:
I'm very interested how this turbo works out. As far as I know you are the 1st to run them.
JasonY
07-09-2011, 12:55 PM
I probably will be on this platform. They do make all their small frame turbos with the same setup which would make twin installs much more drama free. and leak free!
Anyway, tear down has commenced, Tanabe is off the car and im gonna turn it around in the garage before putting it up on stands for the day.
Jason
i would strongly urge you to stay as far away from comp turbos as possible.
look around on supraforums, multiple people have had pretty shitty results with their turbos, they spool a LOT later than garret/borg warner/precision counterparts and dont make as much power.
and i personally havent had good luck with them either.
on top of that their customer service blows.
good luck with the build!
JasonY
07-10-2011, 01:26 PM
Interesting, i have read more good than bad about Comp turbo. I've always noticed if you look hard enough there is enough bad info about every company to scare most people away. Im contemplating a plain ol' journal bearing 4294 right now, should spool like 16gs but make more power and be very suited to the 3.5L thats going in the car this time next year while not sucking on the 3L. Wouldnt be any different than running DR1k's at the worst...then the setup is fitted around a large frame turbo.
Still undecided, Jeff can hook me up on Garrett turbos so its a very appealing option. The only other 40 frame would be the 4088 which is kinda of pointless to do this much work for since its pretty small...
The Borg Warners seem like the top dog right now, so they will always remain an option. I really wanted to try the comp's since im intrigued by not having to deal with oil lines but if they really arent as good as the plain ol' PTE turbos, then maybe i'll deal with two oil lines...
Anyway, heres some pics of the tear down, as it sits now, this afternoon after lunch i'll finally be free of distraction and knock out this tear down in no time.
http://i8.photobucket.com/albums/a48/JasonVR4/Single%20Turbo%20build/2011-07-10_10-39-52_894.jpg
http://i8.photobucket.com/albums/a48/JasonVR4/Single%20Turbo%20build/2011-07-10_11-41-44_324.jpg
http://i8.photobucket.com/albums/a48/JasonVR4/Single%20Turbo%20build/2011-07-10_12-07-48_421.jpg
http://i8.photobucket.com/albums/a48/JasonVR4/Single%20Turbo%20build/2011-07-10_12-08-00_218.jpg
Jason
HellBringer
07-10-2011, 03:20 PM
i would strongly urge you to stay as far away from comp turbos as possible.
Yeah... I'd take that with a grain of salt. I can only recall 3 people that have recently had less than stellar results with Comp - one was a 62 and the other 2 were 80's - and forum post with only a few details and a dyno sheet shouldn't be what one formulates a strong opinion on. It seems most Comp detractors are the vendors that are pushing BW/BEP/PTE. In fact, I can't even recall a single SF vendor that sells Comp... :scratchchin: As already mentioned, you can find negative feedback on every turbo mfg; hell, if you look around lately it seems PTE is really getting a bad rap for all of the recent failures... Does that mean they are all shit and should be avoided as well? I dunno... :dontknow2: I guess my point is I wouldn't take short-term feedback, or the feedback of a few (especially with conflicting interest) as gospel.
My limited experience with Comp has been good (ordered a new turbine housing) and I'm considering either their billet 71 or billet 74 for next year's setup. I have an acquaintance that just made 920WHP at 32psi on pump and meth with a billet 74. :eek4: So much for spooling late and not making power...
JasonY
07-10-2011, 04:43 PM
Holy balls thats impressive power from a 74 :eek: Must...stick...with...a...67mm..lol
Jason
Yeah... I'd take that with a grain of salt. I can only recall 3 people that have recently had less than stellar results with Comp - one was a 62 and the other 2 were 80's - and forum post with only a few details and a dyno sheet shouldn't be what one formulates a strong opinion on. It seems most Comp detractors are the vendors that are pushing BW/BEP/PTE. In fact, I can't even recall a single SF vendor that sells Comp... :scratchchin: As already mentioned, you can find negative feedback on every turbo mfg; hell, if you look around lately it seems PTE is really getting a bad rap for all of the recent failures... Does that mean they are all shit and should be avoided as well? I dunno... :dontknow2: I guess my point is I wouldn't take short-term feedback, or the feedback of a few (especially with conflicting interest) as gospel.
My limited experience with Comp has been good (ordered a new turbine housing) and I'm considering either their billet 71 or billet 74 for next year's setup. I have an acquaintance that just made 920WHP at 32psi on pump and meth with a billet 74. :eek4: So much for spooling late and not making power...
theres a reason that noone on sf sells comp turbos ;)
im a PTE dealer and i'd rather jason buy a garret or borg warner from someone else than comp, im not here trying to make a sale, just sharing my experience and advice.
and on that token, PTE 7175's have made mid 9xx whp also.
92pearltt
08-17-2011, 12:19 AM
get those mani's in yet?
DuTTch
08-17-2011, 12:44 AM
lol dead
JasonY
08-17-2011, 10:38 AM
I was waiting to have Jeff ship the manifolds until i decided on a turbo and spool valve. Since Shiver's valve works on divided manifolds they are ready to go as soon as i get the check off to IPS this week.
http://i8.photobucket.com/albums/a48/JasonVR4/S475.jpg
Borg Warner S475, basically a 4202 with a bigger turbine wheel that somehow outspools the 4202, the spool valve helps tremendously and paired with the 3.5 next year will make for a real fun car with good mid range which even with the valve will be a little lacking on the 3L
Im getting the 4" titanium exhaust from Justin Hutson off Joe's(bybyesti) old car which was another hold up since getting ahold of the Supra's carbon/ti isnt easy to get ahold of and has gone up a lot in price so i was waiting to sort out my options on that and finally have that sorted out.
Just need a NA t-stat housing since the BW doesnt need water lines and im saving my pennies for the Carbonetics triple disc clutch unless anyone has any experience with the Southbend stage 5 which is a single disc rated at 950 torque, i can only imagine that thing sucks to drive in traffic with that kind of torque rating on one disc...?
Jason
BigTyla
08-17-2011, 12:17 PM
Looking forward to seeing your air/water intercooler setup in the car. Been contemplating a setup like that on the Talon to avoid using a front mount but I'm not sure the added complexity is worth it in my case.
Greg E
08-17-2011, 02:46 PM
Just need a NA t-stat housing since the BW doesnt need water lines
Give me a shout. :)
TurboSinceBirth
08-17-2011, 08:51 PM
I love the sound of Borg Warner turbos. Roy's ride comes to mind and it just so happens to be the same turbo. :)
http://www.youtube.com/watch?v=nL7AOxWKuCo
JasonY
08-17-2011, 10:01 PM
Roy had the T6 back end but yeah same turbo. His logs showed 10psi by 4500rpms iirc. Adding the spool valve should liven this thing right up even on the little 3L
Jason
Boostaddict
08-19-2011, 01:59 PM
What is your goal with the car? IMO you might be disappointed with the s475 unless you are making a track-dedicated car, even with a spool valve (especially with the 3.0). Then again BW turbos are cheap so you can always downsize.
AdamVR4
08-19-2011, 02:09 PM
Do yourself a favor and listen to this man ^^^
TT Eric
08-19-2011, 07:06 PM
Jason says he will take the 3.5L route next year He's thinking in advance.
Eric
JasonY
08-19-2011, 07:48 PM
I already know the car is gonna have a fairly poor powerband on the 3L. The 3.5 is going in sometime next year which has always been the plan for the car from the get go.
Chris in 3rd gear had 15psi with the 4202 at 4400 rpms and the boost was only set to 15psi, makes whatever the boost was set to under 5k which on a 3L is pretty good on a turbo that can support as much power, especially since the whole setup isnt really even being built around the 3L.
The difference in 2nd gear was staggering, from basically no power until over 5k to being very much usable by 4k.
Jason
Boostaddict
08-20-2011, 02:41 PM
It will be interesting to see how your powerband compares to mine with the s400 frame turbos, with the 3.0 and 3.5 and with/without a spool valve.
The S400 frame turbine housings aren't very desirable for a spool valve in their stock form without significant internal modification. You might want to contact Chris and see if he's willing to do another one.
JasonY
08-20-2011, 03:29 PM
Chris seems fine with it, i told him which turbo i had and he didnt balk at getting it done. Just need it fitted into the car to ensure clearance for the actuator before getting it done.
I do agree the 400-75 is a lot bigger than i originally planned but i got a really good deal on the turbo and if doesnt work i'll just change it...But i wanted to use the large frame since i dont want to have to change the downpipe, intake, and intercooler piping to swap turbos in the future.
Jason
JasonY
09-11-2011, 02:19 PM
Boostaddict, the 71mm version of my current turbo shares the same back half if im not mistaken, based on everything ive read, its the same turbo on the back end.
I could get the billet 67 which also shares the same back end, but it only comes with the race cover and im not sure if i can find a 5.5" 90* silicone elbow to come off that turbo, not much room to squeeze any bigger of an intake under the fuse box anyway!
BUT, what i am asking, since ive gotten too comfortable with a lot of cash in the bank, im considering just saying F-it and grab the 71mm version of my turbo and still use Chris's spool valve. Would that be worth the downsize, since the turbo is in the exact same frame, it would be zero work to change back to the 75 if i wanted with the 3.5 whenever i feel like spending the money.
Jason
Boostaddict
09-12-2011, 08:56 AM
The smallest off the shelf s400-frame turbo is the 71mm compressor wheel. I'm not aware of a 67mm BW-made s400. The 66mm s300 and EFR turbos are different. Yes you can swap 71mm to 74mm with no problems and might be an option for you. The 71mm is a bit of a dog with the 3.0 but the spool valve will help a little.
HilbillyHomeboy
09-12-2011, 09:55 AM
Boostaddict, the 71mm version of my current turbo shares the same back half if im not mistaken, based on everything ive read, its the same turbo on the back end.
I could get the billet 67 which also shares the same back end, but it only comes with the race cover and im not sure if i can find a 5.5" 90* silicone elbow to come off that turbo, not much room to squeeze any bigger of an intake under the fuse box anyway!
BUT, what i am asking, since ive gotten too comfortable with a lot of cash in the bank, im considering just saying F-it and grab the 71mm version of my turbo and still use Chris's spool valve. Would that be worth the downsize, since the turbo is in the exact same frame, it would be zero work to change back to the 75 if i wanted with the 3.5 whenever i feel like spending the money.
Jason
Look to diesel semi truck parts. That's where I got my 5" rubber/silicone intake for my single.
Jeremy
Boostaddict
09-12-2011, 10:29 AM
Yeah I have a spare one the same as what Jeremy used on his car (5" 90-degree) if you want it. It would probably stretch to 5.5" no problem. Otherwise just fabricate something like this:
http://northbendtech.com/wayne_k/vr4/intake/intake-installed.jpg
JasonY
09-18-2011, 11:41 PM
Found a 5.5-5" elbow.
So anyway, thanks BA for setting me straight and going back to my original plan of the 67mm turbo.
Billet S400SX-67mm is the turbo that will be purchased. Which a/r would you reccomend? Was thinking .90 and saving the money and not getting the spool valve, and i can see how i like the setup and buy a 1.1 or 1.25 and get chris's valve installed in a different T4 backend?
Pics just cuz..haha
http://gallery.theboostlab.com/albums/userpics/IMG_2407.jpg
http://gallery.theboostlab.com/albums/userpics/IMG_2408.jpg
http://gallery.theboostlab.com/albums/userpics/IMG_2411.jpg
http://gallery.theboostlab.com/albums/userpics/IMG_2414.jpg
Jason
mb3000
09-19-2011, 12:54 AM
:bigthumb:
green-lantern
09-19-2011, 12:58 AM
Man those billet wheels are just works of art. I need to see a video of these things being made.
edit: found one, it's amazing what they can do these days.
http://www.youtube.com/watch?v=nTHLs0oFFQo
Sorry to be a bit off topic Jason
TurboSinceBirth
09-19-2011, 02:54 AM
Mmmmmm... that S400 turbos is going to sound so good. Drool...
Boostaddict
09-19-2011, 08:57 AM
The 67mm is a neat option in the s400 frame. As for turbine housings, the 1.25 is too big for the spool device to work properly. The 0.95 is good for the street but is pretty small for a 3.5l. I'd go with the 1 or 1.1 if you don't want to buy more turbine housings later.
JasonY
09-19-2011, 09:06 AM
This is going on the 3L.
Jason
Boostaddict
09-19-2011, 09:08 AM
This is going on the 3L.
Jason
Then the .95 will give you the best possible spool with that huge turbine wheel.
JasonY
09-19-2011, 09:22 AM
okay, thanks! Will be interesting when this thing decides to get going due to that 83mm wheel...
Jason
HellBringer
09-19-2011, 10:20 AM
Couple things:
First, I take back what I said about Comp earlier in this thread. The only person I know making any respectable power with any of their turbos is the billet 74 I already mentioned. ALL of the other results I've seen ranging from 67-80mm turbos have been shit. Customer service and reliability are not an issue, but power and spool are...
RE: BW/BEP turbos -- Can't say I've ever been real impressed with anything I've seen out of their 66-72mm. They don't make any more power (and in most instances less) than the comparable PTE and they're much lazier. Price and reliability is good, but for their mid-sized lineup... well... I wouldn't buy one if I were in the market.
So... Based on all I've been observing over the last few months, PTE billet aka "CEA" really seems like the way to go at this point. They've basically blown everyone else out of the water in terms of power and spool; though I do still question the reliability of their DBB units, and the fact that they aren't serviceable is a concern.
I would consider one of the following options depending on your goals:
6265 -- Easy low 600WHP with incredible spool. Will do 700WHP with supporting mods. Probably the best pure street turbo on the market.
6765 -- Proven easy mid 700WHP with great spool characteristics. Arguably the best street/strip turbo available. Most of the Supra guys are doing low 700's on the stock longblock and upper 700's w/ cams.
7175 -- Proven low 900's at 35psi; mid/low 800's at 30psi with basic supporting mods (cams, etc..). Tolerable spool for the street, but will not be a TQ monster -- will likely hit around 5k. The 7168 might be worth considering as well; should spool much quicker than the 75 but will not have the same top-end. Will probably be tapped out in the mid 800WHP range.
7275 -- Honorable mention because one just put a bone stock original longblock Supra into the 9's @ 150MPH. If that's not impressive, I don't know what is... Big $$$, though.
RE: Carbonetics clutch -- I recently posted some info on this (based on Supra users) in Trevor's thread on 3si. The long and the short is the Carbonetics will NOT stand up to any more than the very occasional drag launch. They are notorious for warping floaters, flywheels, etc... when subjecting to dragging. The old version with the steel floaters would warp if you didn't properly heat them up before doing a dyno pull. The new all-carbon version is better, but still not for drag racing. They are a GREAT street/road course clutch, however. Now consider the 3/s with several hundred lbs more weight and taller gearing... Not a likely bet for success, IMO.
familyMAN
10-04-2011, 09:38 PM
Any updates?
JasonY
10-05-2011, 09:06 AM
Havnt had any time to F with the car. Will probably be doing the full build in about 5-6 weeks. Just piling up parts right now and trying to make some final decisions on which parts to use.
Engine is prepped to pull, might pull it this weekend, but thats only if i am sending the heads to ray for the HL fix if not i'll place the VSS myself and leave them bolted up and save the money. I think with the big back end on the turbo, headlift wont be an issue since my engine will be breathing so much better at a given power level vs Todd's DR750's at ~600awhp. So might be pointless on a stock bottom end since i'll bend a rod before lifting the heads....soooo..MEH
Need to pick a clutch and see if i can get Dave to step my flywheel for me since i know he'll do it right or send my FW to pampena with my bellhousing to get the brace installed and have them step it, i dont trust any shops around here to do it correctly.
When the engine is out, im doing a full ABS delete, complete AWS delete and combining the clutch/brake booster lines to rid myself of the clutter and the tank.
Need to get fan controllers to contol the new fans fortunately i can keep the stock a/c fan in the stock side since stock fans are so much better than aftermarket, i think 3 fans on the rad should be good, 2 pushers and one stock puller. Then the 3 smaller fans on the top heat exchanger also on a temp control after i find out where the system rides temp wise.
Got all the intake stuff, had to go with diesel parts due to the 5.5" intake on the BW turbo. have all the peices to reduce the 5.5 down to 4" for a MAF down in the pass side intercooler location(the stock one no longer there)
Jason
TT Eric
10-05-2011, 04:26 PM
If you are busy like that, means you work a lot, so more $$ to toys! :)
Eric
green-lantern
10-05-2011, 07:34 PM
Not sure how much you want to spend on a clutch but Wayne (boostaddict) is selling his I believe. If you're in that 400-500 buck range then Spec stage 4+ seems to be a good clutch. I run it and like it a lot. Also Dave Broomfield runs it and likes it.
I use a derale fan controller but you need to check the amp's on the fans to make sure you don't burn it up. I just run one fan, I'd need another controller to run two stock fans.
Broomfield Racing
10-05-2011, 08:26 PM
Not sure how much you want to spend on a clutch but Wayne (boostaddict) is selling his I believe. If you're in that 400-500 buck range then Spec stage 4+ seems to be a good clutch. I run it and like it a lot. Also Dave Broomfield runs it and likes it.
I use a derale fan controller but you need to check the amp's on the fans to make sure you don't burn it up. I just run one fan, I'd need another controller to run two stock fans.
My Spec 4+ has hundreds of launches, TONS of 1.7 60 ft's and a whole bunch of mid 1.4 and 1.5 60ft's with the slicks. Im waiting for this thing to blow up but it just won't. You will know when it does though, or starts slipping. 136 mph in a 3500lb car no slipping yet. Not sure if it will hold the power Jason is wanting to make.
It drives awesome too.
JasonY
10-05-2011, 10:56 PM
Seems like i work just to pay taxes. That 5k check i wrote last month has really put a hitch in my plans...sept. quarterly snuck right up on me! Hence the couple weeks late on building this POS.
Jason
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.