View Full Version : Anyone running a 98-99 SL (DOHC) ECU in their VR4?
Drummer
06-24-2011, 10:31 AM
Just wondering how this turned out. I have 2 in the mail, and wondering if they are working good. Thnx!
J-Groove
06-24-2011, 10:41 AM
I don't see why not, you can re-flash them as a VR-4 ECU.
You will need a boomsling adapter to plug it into your existing wire harness depending on what year you are.
-John
Drummer
06-24-2011, 11:22 AM
Im wondering if someone actually did it, and ran into any unknown problems. I have both the adapter harness and the flash cable. Just dont have the ecu's yet.
yellowstealth
06-24-2011, 09:40 PM
I swapped a 99 SL ECU into my 93 stealth, seems to work just fine as far as I can tell. Only thing I've noticed that doesn't work is the boost gauge. To be honest I haven't had a lot of time to play with it. The car's been sitting in my garage for the last several months.. I need to get around to fine tuning the injector scaling/latency and play with the fuel maps a bit one of these days.
Drummer
06-27-2011, 03:25 PM
Sounds promising.. I have one sitting in my P.O. box
Drummer
06-27-2011, 04:20 PM
I swapped a 99 SL ECU into my 93 stealth, seems to work just fine as far as I can tell. Only thing I've noticed that doesn't work is the boost gauge. To be honest I haven't had a lot of time to play with it. The car's been sitting in my garage for the last several months.. I need to get around to fine tuning the injector scaling/latency and play with the fuel maps a bit one of these days.
What did you do about the missing fuel circuit?
Greg E
06-27-2011, 07:58 PM
What did you do about the missing fuel circuit?
The car will still run, just will stay at the high setting all the time. Hot wiring your fuel pump eliminates this circuit anyway.
Drummer
06-27-2011, 08:19 PM
The car will still run, just will stay at the high setting all the time. Hot wiring your fuel pump eliminates this circuit anyway.
Nice. I dont have to touch anything then... for now!
Greg E
06-27-2011, 10:35 PM
Nice. I dont have to touch anything then... for now!
Well, you're still going to have to put the 99 ROM onto it and then you'll get a Check Engine Light from not having any emissions equipment. :p
Drummer
06-28-2011, 12:22 AM
I have those things covered :P I should have said " I dont have to touch any HARDWARE yet"
Jesters Deadd
06-28-2011, 04:04 PM
Aaron and I tested my 98 SL ECU in his Stealth turbo... it worked the best of the ones we tested at NG. I would recommend the 98/99 SL ECU with a hotwired fuel pump over any other ECU besides a true 98/99VR4 ecu.
Drummer
06-28-2011, 05:52 PM
Aaron and I tested my 98 SL ECU in his Stealth turbo... it worked the best of the ones we tested at NG. I would recommend the 98/99 SL ECU with a hotwired fuel pump over any other ECU besides a true 98/99VR4 ecu.
Good thing I went that route... unless I find a VR4 thats not 800 bucks ;)
Jesters Deadd
06-28-2011, 06:03 PM
The only thing missing from the 98/99SL is the oem boost gauge and the dual fuel pump control... oh and the active exhaust... surprising enough the 98/99 VR4 has the circuit for the active exhaust even though they weren't equipt...
yellowstealth
07-07-2011, 02:55 PM
What did you do about the missing fuel circuit?
Sorry, I've been absent for the last couple weeks. As Greg said, I didn't have to do anything for the fuel circuit with the SL ECU, I already had my fuel pump hotwired as well.
aaronatstate
07-08-2011, 03:50 PM
Actually after looking into it further, the knock sensor filter circuit (the one missing in the Montero ECUs) in the SL Board, is the same as the Diamante board. While it works to read knock, it may not be showing the correct value. I would still recommend getting the correct resistors in there.
Jesters Deadd
07-08-2011, 05:59 PM
Actually after looking into it further, the knock sensor filter circuit (the one missing in the Montero ECUs) in the SL Board, is the same as the Diamante board. While it works to read knock, it may not be showing the correct value. I would still recommend getting the correct resistors in there.
Interesting... I did test the Diamante Ecu and got the same amount of knock on the same program as my 99VR4 ecu at the same locations... it wasn't 100% scientific but it was repeatable...
Jesters Deadd
07-08-2011, 06:06 PM
Interesting... I did test the Diamante Ecu and got the same amount of knock on the same program as my 99VR4 ecu at the same locations... it wasn't 100% scientific but it was repeatable...
Which brings up the question... The engine blocks and heads are nearly identical the intakes and exhausts similar. The knock sensors are the same. Wouldn't the block natural frequencies be close and so why are they different?
If its because the the assembly is slightly different so that the filter would require it to be shifted... Then the next question is it important enough to change the resistor?... if yes, then what about all the modified blocks out there? the 3.5l the 3.1l, custom intakes, headers, etc, shouldn't they be just as worried or not worried about their knock freq?
Greg E
07-08-2011, 07:24 PM
Which brings up the question... The engine blocks and heads are nearly identical the intakes and exhausts similar. The knock sensors are the same. Wouldn't the block natural frequencies be close and so why are they different?
If its because the the assembly is slightly different so that the filter would require it to be shifted... Then the next question is it important enough to change the resistor?... if yes, then what about all the modified blocks out there? the 3.5l the 3.1l, custom intakes, headers, etc, shouldn't they be just as worried or not worried about their knock freq?
The difference is engine "noise". The noise of forced induction motors is a lot more audible than an NA. The difference in the knock circuitry in the ECU is just a stronger filter for this noise. It has nothing to do with the size of the engine. The knock sensor sits in the exact same spot as a 3.5, 3.1, 3.0...ect...
The knock sensor is nothing more than a microphone. The filtering is done by the hardware on the ECU. Without this filtering, you're going to see a lot more false knock (assuming the knock sensor is even working correctly).
Now the EVO guys are lucky where the knock filtering is done in the software as well as the hardware but I don't know if such tables exist in the 99 ROM. If they do exist, then that might explain the reason why you didn't see a change in knock (assuming your tune is any kind of aggressive)....
Drummer
07-10-2011, 07:25 PM
Well thats all interesting stuff for sure. I find it no problem to replace the resistors on the motherboard to the values of the VR4. I would rather err on the side of caution. Or not too much caution, in this case lol. I should have everything in my garage by next weekend to start this project. Thank you for the information so far!
Jesters Deadd
07-12-2011, 05:31 PM
Well thats all interesting stuff for sure. I find it no problem to replace the resistors on the motherboard to the values of the VR4. I would rather err on the side of caution. Or not too much caution, in this case lol. I should have everything in my garage by next weekend to start this project. Thank you for the information so far!
By err on the side of caution, do you mean use a lower filter? ie the SL resistor? Because if everthing Greg said is correct, you will see more knock with a lower filter and so you would be "err"ing on the side of caution.
green-lantern
07-13-2011, 01:48 PM
So does this mean all the guys that have been using an NA ECU and piggyback on TT conversions have been potentially getting false knock?
99 vr4
07-17-2011, 06:01 PM
See http://www.3sgto.org/f104/sl-ecu-major-differences-why-not-use-sl-ecu-5756.html
Jesters Deadd
07-18-2011, 01:19 AM
See http://www.3sgto.org/f104/sl-ecu-major-differences-why-not-use-sl-ecu-5756.html
Is that a joke? why are you trying to scare people with the BS about the knock sensor?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.