PDA

View Full Version : How in the sh!t could this happen to my driveline?



MADMarc
06-23-2011, 12:01 AM
I have 20k miles on the "new" transmission and transfer case. I have ALWAYS kept up on fluid levels due to persistent leaks until recently when it became so bad that I parked the car. I have been doing several different things on the car over the past couple days and took the transfer case off today. WHERE THE HELL DID ALL THE TEETH GO?!

These are some shots from the output shaft of the transmission that I already have a replacement for, as well as pictures of the transfer case input teeth.

Transmission:
http://i6.photobucket.com/albums/y214/MADMarc/IMAG0127.jpg

http://i6.photobucket.com/albums/y214/MADMarc/IMAG0131.jpg

http://i6.photobucket.com/albums/y214/MADMarc/IMAG0129.jpg

Transfer case:
http://i6.photobucket.com/albums/y214/MADMarc/IMAG0122.jpg


Oh wait, what's all that crud in the bottom of the tcase?

http://i6.photobucket.com/albums/y214/MADMarc/IMAG0124.jpg

MY SPLINES! How the ef did this happen? The transmission (initially) only leaked from what appeared to be the output shaft seal from the transmission. Reason I say that it was the trans is because the fluid trickled down the area where the tcase and trans meet up but the tcase was never low on fluid. Now, again, I always made sure there was fluid in the transmission yet the shafts look dry as hell, not to mention the powder that the splines were all eroded away in...the powder is the same color as the Redline gear oil I put in there.

Now I'm boned out of more money than I was prepared for...I thought 20k would be find on the magnificent Kormex trans but apparently not. Does anybody have any input? Better yet, does anybody have a good 25 spline tcase they are willing to wave goodbye to?

Austin@STM
06-23-2011, 12:07 AM
the splines are supposed to be dry. No fluid runs in there, the red is just rusty metal shavings from the shaft wearing out. It is a fairly common problem with OEM, and OEM replacement shafts. The way the car is driven has a lot to do with it to. Do you beat on the car much?

MADMarc
06-23-2011, 01:14 AM
Good to hear it is supposed to be dry. I have never had the chance to enjoy my car to the fullest because the clutch would slip whenever I would even try to launch it...that's what I get for reusing a clutch I suppose. To be completely honest I baby the hell out of my car because I was always afraid of something like this happening. Is there anything I need to do before putting a new tcase in there w/the new trans to prevent this from happening again? I would totally understand this happening were it after a significant amount of miles but why so soon? AAAAUGH I NEED MORE BEER TO HELP ME THROUGH THIS!

Chris@Rvengeperformance
06-23-2011, 01:30 AM
You need to grease the splines when installing the transfercase.

Sent from my DROIDX using Tapatalk

UTRacerX9
06-23-2011, 11:28 AM
^^^ What they've said. The stock output shaft eventually rusts and grinds down the spool as well. I've seen worse splines than yours actually. Your transmission leaks are a separate issue.

DocWalt
06-23-2011, 12:05 PM
Amazingly, my transmission leak saved my splines. I've seen way worse splines, but I'd still replace those pieces.

MADMarc
06-23-2011, 01:24 PM
In such a quick amount of time? Yaaaargh, the upgraded output shaft sounds extremely nice these days. My service manual doesn't say what type of grease to use for that connection. What type do I throw in there and just how liberally? :)

Keyan
06-23-2011, 01:30 PM
I plan on stuffing as much wheel bearing grease into my splines as I can, when I install my new tcase in a few months

[Droid X via Tapatalk]

UTRacerX9
06-23-2011, 01:37 PM
In such a quick amount of time? Yaaaargh, the upgraded output shaft sounds extremely nice these days. My service manual doesn't say what type of grease to use for that connection. What type do I throw in there and just how liberally? :)

Some people will advocate a thick assembly lube type of grease, but I don't think that's the best thing. I use motorcycle chain lube. It's designed to be waterproof, not fling off at high chain speeds, and you spray it on. From my experience, it really extends the life of the output shaft.

MADMarc
06-23-2011, 01:58 PM
Thanks for the info. Hell, I might even have some around and not need to go out and buy some. Like Keyan, I WANT to get a buttload of that stuff in there considering what happened but how much is the correct amount?

UTRacerX9
06-23-2011, 02:19 PM
Just spray it liberally on the output shaft (wipe up the excess) and spray some down onto the spool. Any extra will get squeezed out. Ideally, you're supposed to apply chain lube/wax to a hot chain. So you might want to drive around the block or something with the downpipe disconnected, then come back and remove the TC to spray the stuff. I've never gone to that length though. I forget the exact name of the stuff I use, I switched to Chain Wax for my motorcycle as it's a lot cleaner, I think I used to use PJ1.

MADMarc
06-23-2011, 02:30 PM
Thank you for the info. I wonder if it has a high enough viscosity to stay on. How long have you used it and had good splines up until? That's the money maker right there :)

Psychotron
06-23-2011, 02:37 PM
I love threads like this, they make me feel good about owning an NA 3000gt. Sorry about your luck, hopefully a new shaft with lube works out.

UTRacerX9
06-23-2011, 02:38 PM
Well, the PJ1 stuff, once it sets up, is very sticky. It has to be, otherwise a revolving chain would sling it off. For the output shaft, it is directly contacting the spool spines at all times, so it shouldn't be able to fling off at all. I've used chain lube since... 2003? Last I looked at mine I had little to no rust. When I first bought the car, it did have rust on it, but not that bad, because I live in TX and we get dry heat, and don't worry about snow. I don't drive my car that much either, it's a 91 with 92k miles, I've probably put about 35-40k on it using chain lube.

So, for me, it's done it's job of halting excessive rust. I also have a 300M OS to put in the car someday, I will use chain lube on that too.

DocWalt
06-23-2011, 02:43 PM
I used anti-seize the second time my tcase was off, the first time I used regular grease and it was pretty much all squished out of the splines. The motorcycle chain lube sounds great too!

MADMarc
06-23-2011, 02:46 PM
Thanks a bunch for the info UT. I will check that stuff out and if it feels good enough to me I will more than likely end up going with it. You make a good point about it being in constant contact w/the input spool...my bad, should have thought about that.

Psycho...ps, I hate you and your few problems :P

MADMarc
06-23-2011, 02:47 PM
I used anti-seize the second time my tcase was off, the first time I used regular grease and it was pretty much all squished out of the splines. The motorcycle chain lube sounds great too!

That's what I was thinking initially is the anti-seize. Have you pulled it since you put that on there? I'm beginning to think the chain lube is a great idea because it is thinner than both the anti-seize and other grease you used so there's less chance of it smushing out...smushing is a technical term if you're wondering :P

UTRacerX9
06-23-2011, 02:47 PM
No problem :)

DocWalt
06-23-2011, 02:59 PM
That's what I was thinking initially is the anti-seize. Have you pulled it since you put that on there? I'm beginning to think the chain lube is a great idea because it is thinner than both the anti-seize and other grease you used so there's less chance of it smushing out...smushing is a technical term if you're wondering :P

I hadn't taken it off after that before I traded it in, so I don't know, sorry. There was definitely lots of smushing with the anti-seize though, haha.

MADMarc
06-23-2011, 03:03 PM
smushing, squishing...it's all about the technical terms :) Thanks for the info.

apickle
06-23-2011, 05:14 PM
I've always used Valvoline wheel bearing/axle grease in the cardboard tub. It's thick, but it clings like you wouldn't believe. I just coat the shaft and splines a bit past where the seal is, and also rub some inside the spool. I've done that annually for the last 4-5 years, and my output shaft and spool still look like new.

AdamVR4
06-23-2011, 07:35 PM
I use synthetic wheel bearing/axle grease. It might be valvoline. I've had the same tiny tub of it for YEARS now and I use it on the output shaft, input shaft, TOB and clutch fork fulcrum. Obviously I use a very thin film everywhere except the output shaft -- where I'm extremely libruhl ;)

MADMarc
06-23-2011, 08:00 PM
I have some of the Valvoline stuff, I know exactly what you're talking about. Pickle, how many miles did you put on it before checking?