View Full Version : Under the knife. Beginning my 97 conversion.
Amphiron
06-18-2011, 05:24 PM
Started the 97 conversion today getting it ready before it goes into paint.
http://i52.tinypic.com/29aziq9.jpg
It's going terrible for 2 reasons
1. The car was in an accident even tho the carfax was clean
2. The car was fixed by fucking Joe Bob the local drunk or something. Holy crap, the headlight bucket has been banged back into place... with a hammer. All of the bolts have been tightened past their stress point. They all broke pretty much instantly after turning on them just a little even after soaking in PB blaster for 2 hours.
http://i53.tinypic.com/2dtx3iq.jpg
So now I have a pile of broken bolts and I really have no clue how to fix this other then to just drill and tap them out. Or maybe I should buy a bolt extractor?
ive never really had any luck with bolt extractors, chances are those bolts are cross threaded and rusted in there anyway.\
Id skip them and go straight to drilling/tapping. Drill the holes out with a left hand drill bit, you might get lucky on some of the bolts, if not, tap away
Mattdeathdealer
06-18-2011, 05:57 PM
I broke a few a bolts.... not as many as you but i just drilled them out with a smaller diameter bit then the end of the bolt would usally just fall threw. I also soaked the remaining bolt seemed to help. Everything looks nice! except for your light buckets :P
93STLTH
06-18-2011, 10:58 PM
I was lucky, when I did my RT conversion, the only bolts that I had to use an extractor on were for the headlight covers and only 2 at that. Everything else come off like it just rolled off the assembly line last week! One of the benefits of living in So Cal for the past 12 years. :coo3l:
i broke quite a few. if i break several more...i'll probably just get new mount plates for the bumpers/etc. drill/tap is probably best.
you want to talk about PITA? we had to fry the bolts from my mudflaps with a blowtorch & beat the snot out of them in order to get them apart. good times. and that was easy. trying to get my rear OEM brake lines apart without destroying them is impossible.
ictponder
06-19-2011, 10:40 AM
Real easy fix for this. Use a torch to heat up the stud that is stuck. As it cools, spray it with PB Blaster. I had the same problem and was able to turn most of them by hand after this method. It works 100% of the time for me.
Amphiron
06-19-2011, 01:34 PM
Real easy fix for this. Use a torch to heat up the stud that is stuck. As it cools, spray it with PB Blaster. I had the same problem and was able to turn most of them by hand after this method. It works 100% of the time for me.
Thank you so much I hope this works!!
Amphiron
06-19-2011, 06:00 PM
Just gonna drill new holes in some spots and then use self tappers. I just broke a bolt extractor inside of a bolt! OMFG!! and that was after heating it and PB blasting it. That really worked for the other ones tho, thanks man!
Anyways I'm trying to put the 97 bumper on my 94 stealth now but... It wont fit it seems like these mounts for the headlights are in the way... Are those there on the 2nd gen 3000gts?
http://i54.tinypic.com/2dt0t3o.jpg
Hans@GZP
06-19-2011, 06:12 PM
They aren't on 94-98 3000GT's. Only 94-96 stealth and 99 3000GT due to the integrated turn signal to the head light. Just cut it off.
Amphiron
06-19-2011, 06:14 PM
Thanks Hans. Chop chop, wish I woulda knew that before I painted the other bucket. lol
lawdogg
06-19-2011, 06:26 PM
Cut them off and mail em to me. :) I could use em!
With the rust, I have found that a 50/50 mix of ATF and acetone works GREAT. It loosens the rust, and then dissolves the rust if you leave it on for a while. Badass stuff. As reviewed here: Rusty bolts? Make your own super rust penetrant! Grassroots Motorsports Magazine (http://grassrootsmotorsports.com/tech-tips/55/)
yeah, i could use a set of those brackets.
Amphiron
06-19-2011, 09:10 PM
they are gonna need some TLC as the drivers side one is damaged from the undocumented accident. I really don't know how it lined up correctly with how bad it was bent. I'll get some pics tomorrow and pm them to you guys. I don't really think they would be that hard to fix up TBH.
Anyways got the bumper on, just need to get the headlights in and shim it and get all the body parts aligned then its off to paint! I tried to get the headlights in there btw, but it was a real PITA so if anyone has any hints on how to get them to fix with out breaking them (they are glass) would be nice.
http://i55.tinypic.com/1q37ds.jpg
Looks so fucking sweet, makes all the anger worth it. I think it would look even better with a big ass FMIC in there tho. =D
dbest671
06-19-2011, 09:18 PM
Are you using Stealth headlights? Could I buy your turn signal clips off them, since you won't be needing them anymore?
Amphiron
06-19-2011, 09:20 PM
Yeah $10+ shipping sound fair?
dbest671
06-19-2011, 09:22 PM
I don't need the turn signals, thanks though... just the little clips that go on the side of the headlights.
Pm me your paypal address shipping would be 37185.
christ, april. didn't i already sell dave back the one i bought off him? :p let me guess, you're going to do a 99 conversion to the spyder? :suspect:
amphiron, do you have the brackets for the 94-98 bumper turns?
dbest671
06-19-2011, 09:35 PM
christ, april. didn't i already sell dave back the one i bought off him? :p
amphiron, do you have the brackets for the 94-98 bumper turns?
You mean Don :p... yeah I had to use those on a set of Stealth lights that didn't come with them:eh:... those were actually the clips that went to my 99 headlights on the Spyder:mad:
don....lol. i must be high--which is a very bad thing, considering i'm at work right now. :suspect:
so what are you planning to use the new clips for?
Amphiron
06-19-2011, 09:40 PM
Pm sent. Btw the old front bumper is for sale as well, not that anyone would want it it's in good structural shape but will need to be painted. $150.
dbest671
06-19-2011, 09:52 PM
read your supercar roach thread :p
Amphiron, I have some OEM bumper bolts if you need them, the ones that go on the underside. Just pay for shipping :p
Amphiron
06-19-2011, 09:55 PM
I'll take em! lol just send me $5 for the clips instead on paypal and ship em out.
dbest671
06-19-2011, 10:52 PM
Sorry, already paid you. You can refund me the difference, and PM your address, I can get them in the mail tomorrow.
I have 14 of them:
http://i392.photobucket.com/albums/pp4/hoopb23/bumperbolts.jpg
Amphiron
06-22-2011, 10:19 PM
Got the bumper on, woo! I lined the bumper up nice but the hoods wayyyyy off like it was before. It's worse now because the hood wants to hit the headlight, I'll fix that when its at the shop when I have another set of arms to help.
http://i56.tinypic.com/538xv8.jpg
http://i52.tinypic.com/2eqf9tu.jpg
Oh and I clipped a wire or something somewhere. Turn signals blow the fuse as soon as I turn them on, passenger side headlight doesn't turn on and non of the gauges in the dash cluster work! WTF did I do? Jeez!
Amphiron
06-26-2011, 11:03 AM
Just dropped her off at paint, hopefully it'll be done next weekend!!!
Amphiron
03-02-2012, 09:33 PM
Yeah so the painter has taken my money and I haven't heard from him. I've got my car back but looks like i'm just selling the car. Any suggestions on how to get my money back? Hes family so court isn't really an option.
n2nsanity
03-02-2012, 11:02 PM
bust some kneecaps :p
mb3000
03-02-2012, 11:04 PM
Shame you decided to sell the car, only thing you can do with family would be to pester him for the $ or to be repaid in another manner.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.