View Full Version : properly tuned 9b car with cats
Ray Pampena
06-09-2011, 04:55 PM
i see this stuff every day and forget to share. so im sharing... here it is.
take a totally stock 175K 1st gen.. ALL STOCK. add injectors, afc, hot wire, manual boost control... done. makes great power!
http://i27.photobucket.com/albums/c178/raysinsomnia/861217171_photobucket_24667_.jpg
BigTyla
06-09-2011, 05:22 PM
hax!
Actually I'm not totally surprised at the HP numbers. The torque numbers are really good though; did not expect that at all. What boost is this at and what size injectors?
2fnloud
06-09-2011, 05:34 PM
hax!
Actually I'm not totally surprised at the HP numbers. The torque numbers are really good though; did not expect that at all. What boost is this at and what size injectors?
This, I have an AEM series 2 that I am waiting to install with DR700 or DR750, but if there is some substantial gain to be had with just 9b's, I may have to just install it tune it with the 9b's then tune again later when and if I get gibber snails
Ray Pampena
06-09-2011, 06:29 PM
About 17psi then falls to 11. I wouldn't leave 9bs on that build!
This, I have an AEM series 2 that I am waiting to install with DR700 or DR750, but if there is some substantial gain to be had with just 9b's, I may have to just install it tune it with the 9b's then tune again later when and if I get gibber snails
"Gibber" snails, huh?
I thought yours had 13Gs - part of your stage 4 pkg?
2fnloud
06-09-2011, 06:38 PM
I said I don't know what snails I had IF it was 13g then stage 5 ;)
2fnloud
06-09-2011, 06:47 PM
About 17psi then falls to 11. I wouldn't leave 9bs on that build!
Would have no intentions of leaving 9bs, had not intentions of even installing my goodies with 9bs until I read your post.
I said I don't know what snails I had IF it was 13g then stage 5 ;)
Oh - mis-remembered, then, or mis-read the Hennesey stuff you sent me.
Austin@STM
06-09-2011, 09:11 PM
Great numbers, is this on pump?
- 2fnloud - there are very big gains to be had from the AEM alone if you, or someone you know can properly tune it. It is a very great tool to have. You can also shed a few pounds from all the crap you dont need once its installed.
that's an easy 50whp gain over stock. still, you can see that the 9b's are hold the car back.
2fnloud
06-09-2011, 09:25 PM
Great numbers, is this on pump?
- 2fnloud - there are very big gains to be had from the AEM alone if you, or someone you know can properly tune it. It is a very great tool to have. You can also shed a few pounds from all the crap you dont need once its installed.
That is the biggest reason I haven't tried to install this yet. I know of no one in MI that is a reputable tuner. I suppose if push came to shove (ECU fries) I would study hard and ask lots of questions.
I have the series 2 and the Twin fire 4 channel. Plan on adding AEM: Meth, UEGO wideband, One serial gauge, True Boost, Oil pressure, Water temp, and upgreade the OEM sensors to AEM sensors as well while I am at it.
2fnloud
06-09-2011, 09:26 PM
that's an easy 50whp gain over stock. still, you can see that the 9b's are hold the car back.
True, but if I can indeed unlock 50HP give or take why sit on all this stuff for 5 years.
well it's 4.5 hours to IPS from your locale. that's pretty fair. i was 8 hours from 3sx when i had my tt swap done at 3sx.
i don't know that i'd stop at just 9b's if i went to the trouble of AEM. the cost/value doesn't quite match up for me. sure, you can get a LOT more from 9b's with AEM...but the cost is SUBSTANTIAL. an MBC and an SAFC with upgraded turbos will likely be quicker/easier to get more power--for the same cost. 13g/t's & the old-style dr 650's aren't that expensive--especially used.
2fnloud
06-09-2011, 10:33 PM
I have no intention of stopping ay 9b's thinking Billet DR700 (shooting for 500AWHP)
Oh and I own the EMS series 2 already along with the twin fire 4 channel.
sublime_whatigo
06-09-2011, 10:45 PM
Does EMS allow for global injector sizing or something of that sort? If thats the case it would be easier to play with and learn while on stock injectors, and the ability to plug your stock right back in if you need to drive the car is nice.
Oh and nice numbers Ray. Its nice to see a car with any turbo's tuned to its potential.
Does EMS allow for global injector sizing or something of that sort? If thats the case it would be easier to play with and learn while on stock injectors, and the ability to plug your stock right back in if you need to drive the car is nice.
Oh and nice numbers Ray. Its nice to see a car with any turbo's tuned to its potential.
yeah, i think in all the time i've been around the forum, i've only seen 3-4 td04 cars really tuned to max out the turbos. austins with 9b's, dale's with 19t's, and vr3.9's with 13t's are all that come to mind. possibly matt m's dr750's on the 3.5--which showed how they were gassing at that displacement.
GTOJOE
06-10-2011, 04:02 AM
At what point do the 9bs stop effectively pushing air? I know they say the stock fuel system will only handle about 14psi but with a computer, fuel system upgrades and injectors how far could I push the 9bs? I plan to eventually go to DR700/DR750 but for now I am stuck with the 9bs?
2fnloud
06-10-2011, 04:02 AM
well it's 4.5 hours to IPS from your locale. that's pretty fair. i was 8 hours from 3sx when i had my tt swap done at 3sx.
i don't know that i'd stop at just 9b's if i went to the trouble of AEM. the cost/value doesn't quite match up for me. sure, you can get a LOT more from 9b's with AEM...but the cost is SUBSTANTIAL. an MBC and an SAFC with upgraded turbos will likely be quicker/easier to get more power--for the same cost. 13g/t's & the old-style dr 650's aren't that expensive--especially used.
UPDATE:
I was able to rotate the intake clamp around on my front turbo and found the following numbers:
49177-00320....All the numbers but the "2" was raised the "2" was stamped into the housing.
I have 13Gs!!!! :bigthumb::awesome:
UPDATE:
I was able to rotate the intake clamp around on my front turbo and found the following numbers:
49177-00320....All the numbers but the "2" was raised the "2" was stamped into the housing.
I have 13Gs!!!! :bigthumb::awesome:
nice. btw, XPA is in michigan. you might try seeing if they can help you getting your car tuned/built. *edit* according to google maps, it's 106 miles and 1:47 from your town to theirs. that's not bad at all.
http://www.xpauto.net/
At what point do the 9bs stop effectively pushing air? I know they say the stock fuel system will only handle about 14psi but with a computer, fuel system upgrades and injectors how far could I push the 9bs? I plan to eventually go to DR700/DR750 but for now I am stuck with the 9bs?
afaik, austin @ STM has the 9b record. i think that permanent grin or someone else in the UK has tried to make a claim to the full-weight 9b 1/4 record; but austin has the world-record on 9b's; both in the 1/4 and on the dyno (iirc).
2fnloud
06-10-2011, 04:08 AM
Than I knew about XPA, I just don't think that they tune AEM EMS.
Than I knew about XPA, I just don't think that they tune AEM EMS.
perhaps not, but you can always see if you can get a group of MI 3/s'ers together and fly someone like ray to XPA for a tuning day. :)
GTOJOE
06-10-2011, 04:15 AM
afaik, austin @ STM has the 9b record. i think that permanent grin or someone else in the UK has tried to make a claim to the full-weight 9b 1/4 record; but austin has the world-record on 9b's; both in the 1/4 and on the dyno (iirc).
Yeah I gotta read through his thread again. But I was more refering to what max psi can be run with them. I figure at some point they will be so hot that they are going nothing but push hot air which doesn't help anything.
Or I could be on crack.......
Yeah I gotta read through his thread again. But I was more refering to what max psi can be run with them. I figure at some point they will be so hot that they are going nothing but push hot air which doesn't help anything.
Or I could be on crack.......
i'm 99% certain that heat isn't the limitation; it's CFM. 9b's just cannot push enough air to get you to sufficient power beyond a certain point. if heat IS an issue, you need a better intercooler. a glowing turbo doesn't necessarily mean something's wrong.
2fnloud
06-10-2011, 04:29 AM
perhaps not, but you can always see if you can get a group of MI 3/s'ers together and fly someone like ray to XPA for a tuning day. :)
True.
Gearheadvr4
06-10-2011, 04:40 AM
Amazing what these cars do after all those years and nearly pushing 200k.
Still, I tinker too much to leave a little 9b in a car. Turbo upgrades and power are so easy these days on td04.
green-lantern
06-10-2011, 04:59 AM
that's an easy 50whp gain over stock. still, you can see that the 9b's are hold the car back.
Wait, Did I just read this correctly? Did you say rays dyno sheet is 50hp over stock?
Wait, Did I just read this correctly? Did you say rays dyno sheet is 50hp over stock?
well it's not ray's car, but yes...that dyno sheet is just over 50whp improvement above stock (~235-255awhp). when the torque numbers dwarf the hp numbers, the car is choking because the turbos are gassed. we saw the same thing on matt m's dr750's with the 3.5L.
Ray Pampena
06-10-2011, 10:03 AM
this car only made 199whp stock hahaa. this is good for a cheap way to get some quick power for you guys with 9Bs. i still think its silly to leave 9Bs and do other large mods like AEM, frontmount engine work etc.
Austin did great with his 9Bs BUT imagine if he had 15Gs! his car was on E85, aem, custom manifold, front mount etc etc he could have had well over 500awhp and went deep into low 10s with how light the car was. the 9Bs are way too small.. but you can get this power here with minimal mods... after that, put some turbos in there.
my red car makes 530awhp with 650s, fuel, afc, boost control, GM maf.. imagine that car under 3000LBS!
HilbillyHomeboy
06-10-2011, 10:34 AM
199whp stock? Wow, that's awful, lol. Man, I bet the owner has a permagrin now! :)
Good reminder of how much you can get out of an emission compliant 3/S with a solid tune and the right parts. Thanks Ray, you the man, brotha!
Jeremy
green-lantern
06-10-2011, 01:26 PM
well it's not ray's car, but yes...that dyno sheet is just over 50whp improvement above stock (~235-255awhp). when the torque numbers dwarf the hp numbers, the car is choking because the turbos are gassed. we saw the same thing on matt m's dr750's with the 3.5L.
Yeah most stock 3sTT's I've seen put down barely over 200 (Especially the higher mile ones). It's a hell of a gain off of those mods anyway.
Chris@Rvengeperformance
06-10-2011, 04:02 PM
Yeah I gotta read through his thread again. But I was more refering to what max psi can be run with them. I figure at some point they will be so hot that they are going nothing but push hot air which doesn't help anything.
Or I could be on crack.......
15PSI 17PSI 20PSI, doesn't make a whole lot of difference, the 9bs are still maxed out in the upper revs, so if you want to run more boost in the bottom of the rev range it isn't going to hurt anything if you are logging and have no knock. No matter what you run they are still going to drop off to 11 or 12 PSI like everyone else's and be no worse off.
CoreyB
06-10-2011, 04:17 PM
Nice work
x2xtreme360
06-10-2011, 04:55 PM
This gives me a lot of hope.
I'm currently running 23psi on a stock fuel system, besides a hotwire and AFPR. Of course, I do have the MAFT that I'm trying to work out some bugs with. I was thinking about lowering the boost just a tad, but if you calculate the drivetrain loss of the VR4, those numbers would mean that at the crank it's around 400-420HP, which with minimal upgrades that's a really good 100 horsepower added.
2fnloud
06-10-2011, 06:03 PM
This gives me a lot of hope.
I'm currently running 23psi on a stock fuel system, besides a hotwire and AFPR. Of course, I do have the MAFT that I'm trying to work out some bugs with. I was thinking about lowering the boost just a tad, but if you calculate the drivetrain loss of the VR4, those numbers would mean that at the crank it's around 400-420HP, which with minimal upgrades that's a really good 100 horsepower added.
So you are saying that our drive train eats about 50% of the HP?
So you are saying that our drive train eats about 50% of the HP?
no, but 25-30% is fair. if you multiply 309 by 1.25 you get 400-420CHP, so he's right.
HellBringer
06-10-2011, 09:19 PM
This gives me a lot of hope.
I'm currently running 23psi on a stock fuel system, besides a hotwire and AFPR.
:brilliant:
I hope that's your tire pressure.... :runaway:
Goood lawwwdd!
x2xtreme360
06-11-2011, 11:38 AM
So you are saying that our drive train eats about 50% of the HP?
No, lol. 25% of 420 is roughly 315. 50% would be 210.
:brilliant:
I hope that's your tire pressure.... :runaway:
Goood lawwwdd!
I monitor my car, trust me I wouldn't do it blindly.
I'm basically seeing what I can do with the car with minimal upgrades. Zero knock here. Just trying to tune it out.
Kilo_SME
06-12-2011, 12:22 AM
What would it take to make this kind of power on 10:1 compression without harming the engine? 361fwhp would be plenty for me.
What would it take to make this kind of power on 10:1 compression without harming the engine? 361fwhp would be plenty for me.
meth. very, very few people are running > 300whp on a 10:1 on pure pump gas.
What would it take to make this kind of power on 10:1 compression without harming the engine? 361fwhp would be plenty for me.
More than plenty. The challenge with a powerful FWD is getting it to hook up, given that the physics of weight transfer (especially in the lower gears) are working against you.
Not to mention that if you have an open diff, the problem is further compounded by wheelspin acting as a "power fuse".
There's a reason why powerful FWDs (Integra Type R, SRT-4) came standard with LSDs.
DG
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.