View Full Version : Shifter
mb3000
06-08-2011, 05:19 PM
I figured you guys would like a good puzzle. The album link is of pictures of my 1g shifter. Starting in N-1-2-3-4-5-R
As you can see, the arm always stays biased to the right. Got any ideas?
Shifter pictures by mb3000gt_photos - Photobucket (http://s928.photobucket.com/albums/ad128/mb3000gt_photos/Shifter/)
mb3000
06-09-2011, 12:02 AM
I forgot to add that the trans is fully functional & operational.
Rocket
06-09-2011, 12:19 AM
Somebody stick a shift for a RH car in there? Only reason I could think it would lean that way :P
OhioSpyderman
06-09-2011, 08:02 AM
It's obvious that someone cut and welded the arm on your shifter (to make it shorter), and when they did, they turned it 90°......
Bob.
2fnloud
06-09-2011, 09:57 AM
:stupid:
I agree.
mb3000
06-09-2011, 03:31 PM
You ruined all the fun Bob :p
OhioSpyderman
06-09-2011, 06:59 PM
Sorry :)
I co-designed and produced a short shifter for our cars a few years back, so I'm pretty familiar with them....
Bob. :)
mb3000
06-09-2011, 07:12 PM
Wish you could still produce them, but i guess that's just how the cookie crumbled :(
OhioSpyderman
06-09-2011, 07:18 PM
I have not tried to contact my old partner.
I have ZERO fundage to offer him for prints or welding jigs...
Even if I could obtain the above, I have no means to produce them (he built them in his home shop)....
There have been at least two people that offered to reverse engineer them, and I told them I would allow it based on some testing, but that path fizzled....
Wish I could offer more...
Bob.
GTOJOE
06-09-2011, 08:16 PM
Bob send me yours and I'll get it remade.....seriously.
OhioSpyderman
06-09-2011, 08:35 PM
Joe, the arm design is the same for the 91-99 model years, but the base design changes in 94.
I would have to send you both of my shifters, which would leave me without a car to drive :) (I only have ONE each of my own design...)
Bob. :)
GTOJOE
06-09-2011, 08:41 PM
:sad:
DocWalt
06-09-2011, 09:13 PM
Do one at a time? lol
mb3000
06-13-2011, 07:04 PM
Bob, is it possible to swap in a 2nd gen shifter & assembly base from a n/a (5 speed) into my '92?
OhioSpyderman
06-13-2011, 07:35 PM
I haven't tried it, but I would say YES, I think it would...
Bob. :)
mb3000
06-13-2011, 07:50 PM
I haven't tried it, but I would say YES, I think it would...
Bob. :)
Thanks, I think I'm going to try this.
I will report back.
mb3000
06-26-2011, 04:51 PM
Bob, do you know if its possible to remove the base without taking out the center console?
DocWalt
06-26-2011, 05:14 PM
You need to remove the center console, it won't fit out the hole.
mb3000
06-26-2011, 05:33 PM
Damn. I'll be doing this in a couple of weeks then, I need to finish up some other projects before I start this one.
Thanks Doc!
CoopKill
06-26-2011, 10:07 PM
Since Bob's was impossible to get when I got mine, I ended up getting the Seattle SS. I love it, and it has been solid with no issues. 3sx had em...
Chris@Rvengeperformance
06-27-2011, 10:17 AM
Since Bob's was impossible to get when I got mine, I ended up getting the Seattle SS. I love it, and it has been solid with no issues. 3sx had em...
Yeah, seattles shifter is awesome, "great" welds. (Sarcasm)
Sent from my DROIDX using Tapatalk
whitedragon
06-27-2011, 10:23 AM
Yeah, seattles shifter is awesome, "great" welds. (Sarcasm)
Sent from my DROIDX using Tapatalk
You should sell your own custom "Forest Gump Super Vice Grip Race Pro Shifter". Makes a 12.1 pass a cinch!
2fnloud
06-27-2011, 10:48 AM
Wait, Forrest, your shifter welds broke?
You never mentioned that at NG
Chris@Rvengeperformance
06-27-2011, 11:06 AM
Wait, Forrest, your shifter welds broke?
You never mentioned that at NG
yeah first pass down the strip I reached for 3rd and nothing, the shifter was in my hand, snapped off at the point where the rod welds to the assembly on top. Basically no weld, 99% powdercoat. I'll post some pics later. Ran one complete pass with a vice grip shifter for the night @ 12.1 @111. I checked my map again and I was pulling 4 degrees of timing and only 14 PSI. Was going to inch it up over the night, but didn't want to keep trying to shift fast on the vice grips and hurt the trans. At least I know the 2 step rev limit is AWESOME. Only had it set at 4500 and -10 degrees of timing, ran a 1.75 60FT 2nd pass barely trying. If I had a chance to up the revs it would've gone 1.6x easily if nothing broke.
going back to stock and re-welding the seattle to sell probably.
BigTyla
06-27-2011, 11:42 AM
yeah first pass down the strip I reached for 3rd and nothing, the shifter was in my hand, snapped off at the point where the rod welds to the assembly on top.
I can't imagine the plethora of thoughts that were going on in your head at this moment in your life. :D
2fnloud
06-27-2011, 12:04 PM
After you weld it, it shouldn't be an issue....should it?
Chris@Rvengeperformance
06-27-2011, 01:34 PM
After you weld it, it shouldn't be an issue....should it?
no, I'll weld it stronger than its ever been. I've just been debating going back to stock anyway, so I'm going to run around on stock for a week and see how I like it.
Chris@Rvengeperformance
06-27-2011, 01:35 PM
I can't imagine the plethora of thoughts that were going on in your head at this moment in your life. :D
lol, main thing was just keeping enough momentum to make the turn off the track and get out of everyone's way.
mb3000
07-11-2011, 01:01 AM
I'm going to post this up for anyone who is interested in the fitment of the 93+ shifter on the earlier 1st gen years. I finally got around to swapping everything out today, & managed to snap a few pictures along the way.
93+ assembly installed without the slightest issue into my '92 vr4.
Comparison between the two shift arms:
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0835.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0836.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0837.jpg
The 93+ arm simply won't work with the 91-92 base. To make the comparison easier, the 93+ base has the solid bushings installed.
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0838.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0839.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0840.jpg
Here's the 93+ for comparison:
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0843.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0841.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0842.jpg
mb3000
07-11-2011, 01:04 AM
Difference in height between the bases:
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0846.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0847.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0849.jpg
And the different part #'s
Early years:
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0844.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0852.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0854.jpg
mb3000
07-11-2011, 01:07 AM
Later Years:
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0845.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0850.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0851.jpg
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0853.jpg
Another note: Not even the centering springs were the same. (93+ on the bottom)
http://i928.photobucket.com/albums/ad128/mb3000gt_photos/2%20Gen%20Shifter/IMG_0855.jpg
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.