PDA

View Full Version : vcu fried?i



vr4gto
06-05-2011, 02:58 PM
Just trying to get an idea what I'm in for. I recently finished putting new seals and bearings in the transmission and transfer case as well as a clutch. I was driving last night on my way home and heard a clunk then the engine revved freely. Pulled over, no fluid on the ground, clutch feels normal and will go in all the gears. It just won't move. I'm assuming the vcu went?

stealthee
06-05-2011, 04:15 PM
Sounds to me like a stripped output shaft. You can still drive the car with a fried VCU.

green-lantern
06-05-2011, 04:23 PM
Sounds to me like a stripped output shaft. You can still drive the car with a fried VCU.

This......

vr4gto
06-05-2011, 04:55 PM
It will move now but not well. Makes a whining noise. Why would it strip while cruising? I haven't launched it in years and never had an issue since until now. The splines looked good too while it was apart.

green-lantern
06-05-2011, 08:21 PM
IDK, sounds weird, doesn't sound like the VCU though.

stealthee
06-05-2011, 08:34 PM
It will move now but not well. Makes a whining noise. Why would it strip while cruising? I haven't launched it in years and never had an issue since until now. The splines looked good too while it was apart.

Flat out wear will do it. People dont keep there OS's greased and rust will wear the teeth to points. They are supposed to look more like mesas. Eventually enough wear happens to strip it out if not maintained.

vr4gto
06-05-2011, 09:46 PM
I put the car up and tried getting the wheels to spin in gear with the car running. No go. Turned off the car and left it in gear and the front wheels can be spun freely. The back are more resistant. Took it out of gear and all four move freely.

IPD
06-05-2011, 09:59 PM
you shouldn't be able to turn your wheels with the transmission engaged & the engine off. if they turn freely, you've got a broken component in your drivetrain. i third the output shaft.

green-lantern
06-05-2011, 10:12 PM
I put the car up and tried getting the wheels to spin in gear with the car running. No go. Turned off the car and left it in gear and the front wheels can be spun freely. The back are more resistant. Took it out of gear and all four move freely.

How resistant are we talking here on the rear wheels? I want to say it's a TC issue but since you've been in the trans recently you might have not assembled something correctly. Drain the gear oil out of the trans and check for metal. If you replaced all the bearings it might have needed to be shimmed. Did you check the the preload?

vr4gto
06-05-2011, 10:22 PM
There's normal resistance on the back wheels. The front can be turned with a finger easily. The noise I'm hearing is coming from near the passenger front axle.

RealMcCoy
06-05-2011, 11:21 PM
The front wheels will spin freely, but I imagine they're spinning in opposite directions... The front differential is open, there is no limited slip. If you turn one axle, it will just turn the spider gears, and the opposing wheel will spin the opposite way.

So you had all four wheels off the ground, running in gear, and no wheels were turning?

aaronatstate
06-05-2011, 11:25 PM
Again for the output shaft. Now if you've driven it with the stripped output shaft there is a good chance the VCU is fried as a result.

vr4gto
06-05-2011, 11:30 PM
The front wheels will spin freely, but I imagine they're spinning in opposite directions... The front differential is open, there is no limited slip. If you turn one axle, it will just turn the spider gears, and the opposing wheel will spin the opposite way.

So you had all four wheels off the ground, running in gear, and no wheels were turning?

Nope.

RealMcCoy
06-05-2011, 11:32 PM
I'd normally be jumping on the output shaft bandwagon as well, it is a very common failure. The fact that you JUST had it apart, and stated that you thought it was in good condition, combined with the fact that you just had it apart... I'd want to make sure the front axles are fully seated before diving any deeper.

vr4gto
06-05-2011, 11:34 PM
Again for the output shaft. Now if you've driven it with the stripped output shaft there is a good chance the VCU is fried as a result.

It wasn't driven far. It was backed up into a spot in the shop and then it wouldn't move anymore. Last night when it made the clunk I pulled over right away. But I'm definitely not getting my hopes up that the output shaft or the vcu are going to be ok.

vr4gto
06-05-2011, 11:35 PM
I'd normally be jumping on the output shaft bandwagon as well, it is a very common failure. The fact that you JUST had it apart, and stated that you thought it was in good condition, combined with the fact that you just had it apart... I'd want to make sure the front axles are fully seated before diving any deeper.

That's one thing I'm gonna check into tomorrow. Only got to mess with my car in between customers today.

vr4gto
06-06-2011, 04:54 PM
Well I figured it out. Brand new clutch plate separated and jammed everything up, blew out the diff and probably everything else. And the best part is my wife cleaned my "mess" of paperwork and threw all my receipts away. It's a good thing I like her.

green-lantern
06-06-2011, 05:01 PM
Damn! That sucks :(

vr4gto
06-06-2011, 05:19 PM
Yep, it does. Just rebuilt it now I'm broke for awhile on spending money for this car.

vr4gto
06-06-2011, 07:14 PM
Wow I hate my friends right now. They offered to pull the trans for me today to check it since I don't have time. They pranked me, the clutch plate did blow, but the trans is fine. Bastards.

green-lantern
06-06-2011, 07:25 PM
Wow I hate my friends right now. They offered to pull the trans for me today to check it since I don't have time. They pranked me, the clutch plate did blow, but the trans is fine. Bastards.

:lol: What dicks! I was thinking it was awfully freaking weird for the diff to break. ha ha

vr4gto
06-06-2011, 07:42 PM
:lol: What dicks! I was thinking it was awfully freaking weird for the diff to break. ha ha
That's what I was trying figure out. I kept questioning it and finally one cracked and gave it away. I was already trying to figure out how to convert an 18 spline I have over to 25 at that point. So apparently the truth is the clutch plate did break and my buttface wife was in on it all and she has the receipt. I guess this was pay back for all the shit I've pulled on all of them.

U

green-lantern
06-06-2011, 07:54 PM
Ha ha Karma's a bitch huh? Well at least it's just a clutch.

vr4gto
06-06-2011, 08:18 PM
Ha, no kidding. I might as well upgrade the output while the trans is out again. Can't figure out why the clutch did that though. I'll see what kind of damage it did tomorrow.

green-lantern
06-06-2011, 08:38 PM
Ha, no kidding. I might as well upgrade the output while the trans is out again. Can't figure out why the clutch did that though. I'll see what kind of damage it did tomorrow.

What clutch is it? Are you sure it was adjusted properly?

aaronatstate
06-06-2011, 08:49 PM
If your VCU had been fried, I have an 18 spline I'm trying to get rid of :w00t:

vr4gto
06-06-2011, 08:49 PM
What clutch is it? Are you sure it was adjusted properly?

It was an oem one. I bet that's the problem. I didn't do anything but put it in. What should have I done? It felt fine so I didn't think anything of it.

vr4gto
06-06-2011, 09:51 PM
Doh, I didn't adjust the pedal.

green-lantern
06-06-2011, 10:41 PM
Doh, I didn't adjust the pedal.

Some times you need to. If it was engaging at the top of the pedal it might have been slipping. My brothers plate disintegrated like that. You want at least one inch of play at the top so you know the pressure plate is clamping full force.

vr4gto
06-06-2011, 11:20 PM
Well, I'm going by what my friends are telling me about the clutch plate being in pieces. And judging by the bs they're spewing today I'm not taking any of it for truth. Maybe I'll be able to adjust it and it will be fine. I'm hoping to be able to check it out myself tomorrow.

vr4gto
07-17-2011, 11:20 PM
Ok, so after a month of bullshit speculation by myself and my buddies, I finally got my ass out to the garage. I'm gonna guess this is my whole issue?
http://i56.tinypic.com/wl428j.jpg

Alex3000gt
07-18-2011, 12:24 AM
Driver's side axle came out of the intermediate shaft!?

How in the world does that happen?

vr4gto
07-18-2011, 01:16 AM
You got me. Xwire said to check the circlip. Rusted and broke maybe?

vr4gto
07-20-2011, 05:46 PM
Took the axle out and brought it into a driveline shop. They can't figure out how it came apart. I couldn't get it back together until after I undid the axle nut to take it all out. Any chance this fucked up my tranny? I haven't put the axle back in yet, and it still goes in all gears. I'm hoping this is the only reason the car won't move.