View Full Version : Electronics question
peterkottemann
05-28-2011, 10:13 PM
Does anyone know if I can use a second gen ECU inside a first gen car?
Just found out my caps leaked and blew the ISC through the back of the motherboard... I can fix a lot, but when you can see daylight though the circuit board, just write that one off...
BaadVR4
05-28-2011, 10:46 PM
Short answer: no. They use different signals to determine crankshaft/camshaft position.
mb3000
05-29-2011, 01:41 AM
If it's a 93 than it will use the separate cam & crank sensors like the 2nd gen.
lawdogg
05-29-2011, 04:44 PM
Yes, you can use it, and it's super easy. You don't even need to do anything special. I am running my 94's ECU in my 92 after modifying only one wire. The 3 plugs just plug right in.
Ok so thanks to CoreyB to pointing this out ... you all might know this but I'm a little obtuse.
To make an adapter harness between a 1g and a hybrid ECU, the only thing you have to worry about is the little 12-pin plug. The other three plugs are for all intensive purposes directly complimentary.
See http://www.plxdevices.com/ECUDatabase/Mitsubishi/Mitsu_Dodge_3000GTVR4_StealthTT_91_97.pdf.
Only 1 pin *needs* to go into the hyrid's 12-pin plug:
A quick run-through of the terminals off Stealth316 shows these pins are all in the 12-pin plug on the 94-95, and here's where they get their signal from on the 91-93:
Pin 59: A/C Switch 2
Pin 60: Rear heated o2 sensor, emissions (cali) - not present in 91-93
Pin 58: Engine Ignition Signal
Pin 52: Ignition Timing Adjustment Terminal
And come from these pins on the 91-93:
Pin 20: A/C Switch 2
Pin 101: Engine Ignition Signal
Pin 104: Ignition Timing Adjustment Terminal
In other words, if you want to run a 1g ECU on a 94-95, or a hybrid ECU in a 1g, you'll pretty much only have to deal with the Engine Ignition Signal and the 12-pin plug. SO there's no need to build a fancy adaptor harness unless you want to use it as a boomslang harness or something along those lines.
Thanks Corey!
To account for the different CAS sensor latency ... http://www.stealth316.com/2-cas_conversion.htm
peterkottemann
05-30-2011, 07:29 AM
thanks law, it might be worth the trouble considering the price difference. I'll see if I can dig up a first gen at the same price though.
x2xtreme360
05-30-2011, 02:52 PM
Keep in mind, you MUST use a fed spec in order for it to work. Cali spec cars had the 4 plugs like the OBDII cars.
1993RT/TT
05-31-2011, 11:42 PM
Keep in mind, you MUST use a fed spec in order for it to work. Cali spec cars had the 4 plugs like the OBDII cars.
My 93 Cali spec turbo has 3 plugs. Hopefully you have a 91 or 92 they are easier to find
x2xtreme360
06-01-2011, 01:57 AM
My 93 Cali spec turbo has 3 plugs. Hopefully you have a 91 or 92 they are easier to find
If this thread is about a VR4, an adapter harness would be needed. ALL Hybrid and OBDII turbo cars use a 4 plug harness (except for 98-99 which use a 3 row harness).
lawdogg
06-01-2011, 05:13 PM
No no, this is what I'm saying. All 94-95, at least, hybrid ECUs have 4 plugs. The 3 plugs from 91-93 ECUs plug right in to 3 of those plugs. The fourth plug only needs one wire taken out of the 91-93 harness and connected.
To put the 94-95, fed or cali, into a 91-93 car .... simply plug all three plugs into the ECU. The remaining port, the little 4th plug, only needs one wire taken from the 91-93 harness and connected on its own, as I outlined above.
It absolutely works.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.