PDA

View Full Version : Dyno Results: Stock MAS VS. MAFT Version 2



Emilie@GZP
05-25-2011, 10:24 PM
We had installed a set of 16T's on 3KVT's 3000GT VR-4, but ran into some stuttering issues last time we dyno'd it. We got that issue resolved with a replacement coil pack, and hit the dyno again yesterday. at 1.07 bar, we dyno'd 323AWHP, with the stock MAS.


http://www.youtube.com/watch?v=C3vNcsUXJp0&feature=share

After speaking with Marc, we all agreed that it would be beneficial to rip out the stock MAS, install a 3.5" GM MAS and a MAFT Version 2, as the stocker just seemed very restrictive.

We installed that earlier today, and ran the car again. It put down 360AWHP at 1.06 bar... :eek:

Needless to say, we are extremely impressed with the power gains from just adding the MAFT Version 2. With some more time and some more tweaking, we could definitely squeeze more power out of her, but she's running like an absolute CHAMP right now.


http://www.youtube.com/watch?v=7A68W3ROllg

Dyno chart. Stock MAS vs MAFT Version 2
http://www.3swarehouse.com/images/stories/misc/marc%20lewis%20stock%20mas%20vs%20maft%202.jpg

For anyone interested, you can purchase this directly through our site:
http://www.3swarehouse.com/index.php?option=com_virtuemart&page=shop.browse&category_id=238&Itemid=1

vr3.9
05-25-2011, 10:32 PM
Good real world test and data. I know that it makes a huge difference after you reach 400awhp. Great to see such results at lower levels too.

x2xtreme360
05-25-2011, 10:34 PM
I did a complete conversion from stock MAF to 3.0GM MAF with MAFT Gen II.

On stock MAF, I had misfiring up the ass at 15psi under WOT.

On Maft, direct swap, NO tweaking, 23psi, ALL studdering from misfires went away and it was smooth sailing all the way up to redline.

Best mod I've done thus far.

Blackmount
05-25-2011, 10:36 PM
Im convinced! did you use any other type of device for tuning besides the the Maft2? I forget what all the extra stuff the Maft2 does over the original MAFT. but i know with the Original alot of people..at least DSM guys, ran a MAFT\SAFC Combo.

x2xtreme360
05-25-2011, 10:39 PM
Im convinced! did you use any other type of device for tuning besides the the Maft2? I forget what all the extra stuff the Maft2 does over the original MAFT. but i know with the Original alot of people..at least DSM guys, ran a MAFT\SAFC Combo.

The GenII is NOTHING like the original. No need for double piggybacking. The Gen II does wideband tracking, has a wide range of inputs, you can log directly from the unit, adjust sooooooooo many different parameters across any RPM scale. The wiring is as simple as it gets. 10 wires tapped at the ECU (boomslang recommended) and you're off to the races.

Hans@GZP
05-25-2011, 10:40 PM
Nothing in combo with it. There is no need. It is by far a way more advanced piece than the original maft. For the small price difference, it's a no brainer. The results from the stock maf was using an emanage blue for fuel and timing control.

Blackmount
05-25-2011, 10:50 PM
sounds like I know what to put some money aside for next month. already bought my toys this month. Thanks!

familyMAN
05-25-2011, 10:54 PM
Great results! Thanks for sharing. Good to hear positive results with the gen2.

Hans@GZP
05-25-2011, 11:01 PM
Just remember to support the vendors that give you the results!!!!

3KVT
05-25-2011, 11:08 PM
Fuck yes!!!

rawavr4
05-25-2011, 11:12 PM
Awesome results. I guess im selling the safc2.

familyMAN
05-25-2011, 11:27 PM
This was still draw-thru, correct?

x2xtreme360
05-25-2011, 11:31 PM
This was still draw-thru, correct?

Probably not. There's little to no reason to use it in draw through, unless you have some issue like a demonized OBDII ECU or something that doesn't like it.

Goallie11
05-25-2011, 11:33 PM
Will the same benefits be seen from just upgrading to a 3.5 in mas? Or do you have to have the translator too?

Hans@GZP
05-25-2011, 11:33 PM
It was setup as blow thru. We modded the CX Racing fmic pipe to do it.

Hans@GZP
05-25-2011, 11:35 PM
Will the same benefits be seen from just upgrading to a 3.5 in mas? Or do you have to have the translator too?

You need something to change the signal from one type of sensor to another. The translator does that along with sending the ecu a temp signal and barometer signal.

x2xtreme360
05-25-2011, 11:35 PM
Will the same benefits be seen from just upgrading to a 3.5 in mas? Or do you have to have the translator too?

The GM MAS cannot function without the translator.

vr3.9
05-25-2011, 11:37 PM
It was setup as blow thru. We modded the CX Racing fmic pipe to do it.

Could you put up some pics and info of this and what did you use for intake pipes to the turbos?

Hans@GZP
05-25-2011, 11:39 PM
Could you put up some pics and info of this and what did you use for intake pipes to the turbos?

I'll post up some pics tomorrow. We are still on stock intake pipes. We used a 4 inch pipe and filter to replace the stock maf.

x2xtreme360
05-25-2011, 11:55 PM
Could you put up some pics and info of this and what did you use for intake pipes to the turbos?

All you need to do with the CX racing kit is cut the pipe near the TB and place the MAF right there. I personally used my DNP Ypipe to modify it to fit the GM MAF.

http://www.3sgto.org/f13/my-custom-dnp-blow-through-y-pipe-4446.html

For the intake, I run filters on the turbos now. No intake pipes.

rawavr4
05-25-2011, 11:56 PM
Did you use the wideband tracking option on the gen2? And did it give you any problems? This looks much simpler than the maft+safc combo i was going to do.

x2xtreme360
05-26-2011, 12:00 AM
Did you use the wideband tracking option on the gen2? And did it give you any problems? This looks much simpler than the maft+safc combo i was going to do.

With the Gen II, using the old unit is just not the way to go. No point in using two piggybacks.

The wideband tracking only attempts to get to your specified range. It in no way does the work for you.

Hans@GZP
05-26-2011, 12:02 AM
You need to relocate the bov tube and get some 3-3.5 hose couplers.


All you need to do with the CX racing kit is cut the pipe near the TB and place the MAF right there. I personally used my DNP Ypipe to modify it to fit the GM MAF.

http://www.3sgto.org/f13/my-custom-dnp-blow-through-y-pipe-4446.html

For the intake, I run filters on the turbos now. No intake pipes.

Hans@GZP
05-26-2011, 12:03 AM
Did you use the wideband tracking option on the gen2? And did it give you any problems? This looks much simpler than the maft+safc combo i was going to do.

I don't use wideband tracking. It's unreliable.

rawavr4
05-26-2011, 12:05 AM
Hans do you have the Maft v2 in stock?

Hans@GZP
05-26-2011, 12:10 AM
I usually get them next day unless Em feels like taking a drive to Philly.

rawavr4
05-26-2011, 12:13 AM
I'm sure she won't mind since shes turbed now. I'll be up there tomorrow after work to pick up the stuff and talk about this.

Emilie@GZP
05-26-2011, 12:15 AM
Tolls and gas get expensive.... but I can be persuaded to make the drive.....

Hans@GZP
05-26-2011, 12:18 AM
I'm sure she won't mind since shes turbed now. I'll be up there tomorrow after work to pick up the stuff and talk about this.

And PINK!!! I can't wait to finish her engine bay lol.

rawavr4
05-26-2011, 12:22 AM
Its gonna be the girliest stealth ever. I'd be devastated if i got beat by a pink engine bay lol

Emilie@GZP
05-26-2011, 10:41 AM
:runaway:

aaronatstate
05-26-2011, 11:10 AM
I noticed a huge difference switching over to the Evo MAF. Any and all hesitation at higher RPMs went away, and the AFR is a lot more stable now as well.

Goallie11
05-26-2011, 12:57 PM
You need something to change the signal from one type of sensor to another. The translator does that along with sending the ecu a temp signal and barometer signal.

Ok so I worded it wrong, but would you see the same benefits if you switched from a stock mas to the 3.5 gm one and used in my case and emanage blue? Or does most of the benefit come from the maft-2?

Hans@GZP
05-26-2011, 01:05 PM
Ok so I worded it wrong, but would you see the same benefits if you switched from a stock mas to the 3.5 gm one and used in my case and emanage blue? Or does most of the benefit come from the maft-2?

You still need the translator. You can't run a GM MAF on a 3/S without one (unless you are flashing ecu's, but that's a whole different ball game). There is no need to run an emanage with it unless you want timing control. But, you can do that with the MAFT Pro. It's nicer to have everything all in one unit.

Here is a break down of the 3 different MAFT units so you may better understand what is what. Either way, you need one of them to run a GM MAF on your 3/S.

MAFT Original: Mounted in engine bay with knobs to tune with. You can only tune fuel curves with it. It has RPM and load based tuning. Pretty much obsolete at this point.

MAFT Version 2: Mounted inside the car. You can very easily tune by load (low, mid, high) at many different RPM points (a lot more than the original). It allows for wideband tracking and datalogging (neither of which I have ever needed to use). You can run the same unit on many different types of vehicles that is is pre programmed for (the original was vehicle specific).

MAFT Pro: Does everything the version 2 does, but allows for timing control and even the ability to run speed density. I don't know of anyone that has done the speed density conversion successfully, but it can be done. I don't really see a need for it as the blow thru setup nets great results.

There are more features to these units, but this just touches on the main points of each of them.

aaronatstate
05-26-2011, 02:52 PM
You can't run a GM MAF on a 3/S without one (unless you are flashing ecu's, but that's a whole different ball game).

Dont know if that will ever be available. I know Greg is looking at trying a GM MAF with his 99 car that he is flash tuning, but he's still going ot use the translator and just zero it out.

UTRacerX9
05-26-2011, 04:01 PM
This looks much simpler than the maft+safc combo i was going to do.


With the Gen II, using the old unit is just not the way to go. No point in using two piggybacks.

I don't understand why everyone is saying you need two piggybacks with the original MAFT. I've never used two piggybacks with mine, and some of the other oldtimers using this unit never did either. I forget which version I have, it was a later revision, I know that much. I have 550cc injectors in my car, and from what I remember, I had to tune it with the settings for 510cc to get the best results. It idles fine and drives fine under boost. That being said, if given a choice, I'd go with the newer version. But I'm just here to state that you certainly do not need to buy a SAFC to go with the MAFT.

mannavr4
05-26-2011, 08:28 PM
I don't understand why everyone is saying you need two piggybacks with the original MAFT. I've never used two piggybacks with mine, and some of the other oldtimers using this unit never did either. I forget which version I have, it was a later revision, I know that much. I have 550cc injectors in my car, and from what I remember, I had to tune it with the settings for 510cc to get the best results. It idles fine and drives fine under boost. That being said, if given a choice, I'd go with the newer version. But I'm just here to state that you certainly do not need to buy a SAFC to go with the MAFT.

Your correct in saying you dont need 2 as I only have the original maft, But you can add the safc and fine tune it that much better. I plan on adding it to my setup.

UTRacerX9
05-26-2011, 09:53 PM
Your correct in saying you dont need 2 as I only have the original maft, But you can add the safc and fine tune it that much better. I plan on adding it to my setup.

The original MAFT could adjust fuel curves in 5% increments (possibly even 2%, but it's been so long I don't remember.) At any rate, 5% is going to get you very close to where you need to be. Spending the money on a safc is wasting money IMO, that would be better spent on an AFPR if you want to fine tune your fuel delivery, which is what I have done.

Rakuny
03-06-2012, 10:02 PM
wow, think that the GM maf would provide a worth while gain on a 13T stock injector car?

B-Man
03-06-2012, 10:10 PM
Wanna find out, Mark? ;)

anyonebutme
03-06-2012, 10:26 PM
I don't know of anyone that has done the speed density conversion successfully, but it can be done.



:::clears throat:::

My car wasn't running on pixie dust at NG 08 and 09...

Hans@GZP
03-06-2012, 10:26 PM
Your car ran? :p

anyonebutme
03-06-2012, 10:34 PM
Your car ran? :p

it "ran", the quotation marks are important...

B-Man
03-06-2012, 10:42 PM
I don't know of anyone that has done the speed density conversion successfully, but it can be done.


Jeremy C and I both had speed density running fairly well on our FWD TT cars with MAF-T Pro, though I never upped it past 8psi before I sold it, he was running more.

Rakuny
03-07-2012, 08:35 AM
Wanna find out, Mark? ;)

I've been thinking about it...

B-Man
03-07-2012, 08:45 AM
I've got one :suspect:

HLxDrummer
03-07-2012, 08:54 AM
So when you ran the stock MAS was it tuned? How about with the GM? Just wondering if the difference is solely due to the MAF size, or to tuning as well.

Also, do people run into driveability issues with translators/GM MAFs?

Emilie@GZP
03-07-2012, 10:00 AM
So when you ran the stock MAS was it tuned? How about with the GM? Just wondering if the difference is solely due to the MAF size, or to tuning as well.

Also, do people run into driveability issues with translators/GM MAFs?

Both of those runs were tuned. But both of those videos were shown at the same boost level.

IPD
03-07-2012, 05:55 PM
good results. i have high hopes for my gen-1 3.5" & safc2.

SpdDmnVR4
03-08-2012, 12:24 AM
Hmm.. 40 whp gain. good real world test. but I have a few questions. Was this at the exact same timing level? Was it done at the same boost? Same AFR?

A 40 whp gain from just swapping a simple component like that seems like a HUGE gain. I know there are substantial gains/ability gained when you run out of Hz on the stock MAS (above 400whp generally), but i find it almost unbelieveable it gained that much on such a mild setup.

Im on 14 psi now at 10.4 AFR and about 18-19 degrees peak timing @ 7000RPM and stock MAS. I dont have a dyno locally to test on, so I am forced to do my own street tuning. However, I did trap 109 in the quarter at a full weight( spare tire, jack, all accessories, ~3900 lbs) which i believe puts me about 350 awhp +/- 20whp. Perhaps I am being a bit more generous than I should be...

I guess Ill have to look into doing a blowthru set up sooner rather than later.

Hans@GZP
03-08-2012, 09:34 AM
The tests were done as closely as possible to each other. Even within a few days (SAE corrected numbers to net the same results on different days.