PDA

View Full Version : My LCD screen project, boost, WBO2, Knock, etc



Pages : [1] 2 3 4 5 6 7

BlackStealth
09-14-2010, 08:00 PM
I know some of you don't visit the other forums, so I'll show you what I made.

I built something to replace my scanmaster and greddy profec B spec II boost controller and to make it easy to see while driving. It shows the AFR of my wideband O2, boost pressure in PSI, and knocksum from the ECU. If I want to see other datalogging parameters in real time I simply turn a rotary knob to the right. If I want to change my boost settings I turn to the left. To make changes, I simply push down on the knob.

Works with all year model 3/S cars (91-93 OBD1), (94-99 MUT). My friend with his 94 RT/TT wanted one so I spent a few months analyzing the MUT protocol and made it work. It can view Knock, Timing, Fuel trims, etc. Basically anything OBD1 can datalog, MUT can view too.

Because it's two products in one, I can for the first time have this boost controller respond to knock. ie. Lower boost if engine knock is present.

Another thing that worries me if my tune may drift lean when weather changes drastically. It will monitor for knock, and AFR and if it gets too lean with a small amount of knock, it will warn flash the screen red to get my attention and show how much knock was present, the WBO2 AFR number, boost pressure PSI, and RPM. Armed with this four pieces of information I can adjust my tune if needed be.

Temperature can have an influence on boost, so I've made a table that will re-adjust the duty cycle in order to maintain a more consistent boost.

I lose about 2 psi at redline because of my stock catback, this is no longer a problem. At 4000, 4500, etc RPMS, I add more duty cycle to compensate. Now I get steady boost across.

Displays CEL codes in english, no need to have a chart with you.

Earlier video of it in action. I've changed the menus a bit since.

http://www.youtube.com/watch?v=AMGRbN59SCA

Video showing the config menu, and exploring a bit.

http://www.youtube.com/watch?v=G5Q70j_gRfg&feature=channel


http://i782.photobucket.com/albums/yy107/blackstealth_2009/red.jpg

http://i782.photobucket.com/albums/yy107/blackstealth_2009/nocolor.jpg

http://i782.photobucket.com/albums/yy107/blackstealth_2009/scanboostlabeled.jpg

akotten
09-14-2010, 08:07 PM
I remember seeing this. I would LOVE to buy one of these.

thor'svr4
09-14-2010, 08:15 PM
thats nuts!

DrGonzo
09-14-2010, 08:32 PM
Again when are these for sale???? :)

Chris@Rvengeperformance
09-14-2010, 08:58 PM
badass, let me know $$

ABattaglia
09-14-2010, 09:03 PM
Wow looks like a great product. Count me in.

CoreyB
09-14-2010, 09:07 PM
One of the coolest mods I have seen

rdmelton
09-14-2010, 09:08 PM
Wow, that is an incredible product for an individual into make. It is as good or better than most professional products that I've seen, even including other platforms that have a lot more aftermarket support. Just curious, what is your background (I'll take a guess and say electrical engineer?) and do you anticipate selling these?

USDM-GTO
09-14-2010, 09:43 PM
subscribed to see if a sale will happen on this.

BlackStealth
09-14-2010, 11:56 PM
I'm an unemployed electrical engineer / computer science guy so with my free time I made what I desired for my car. I've made a couple extra units, and sold some to my local 3S friends. I won't put a price up because I think I might be breaking a forum rule then. If you really want one, you will have to contact me outside the forum so we don't do anything wrong.

FstAsVR4
09-15-2010, 12:04 AM
Contact information? Great mod for sure looks like you could make a killing on this and more products.

DocWalt
09-15-2010, 12:32 AM
Yep, still badass. Damn it, my place of work is screwing me out of more work :(

x2percentmilk
09-15-2010, 12:35 AM
beautiful!
thumbs up for diy electronics

BigBoris
09-15-2010, 12:36 AM
I'm interested! Contact me with a price please? Will it work with a 96 Base N/A?

marshallh
09-15-2010, 12:37 AM
Certified badass, great job. Is that an AVR or PIC?

DocWalt
09-15-2010, 12:40 AM
At this rate they'll all be gone before I get a chance, LOL

Flamer
09-15-2010, 04:24 AM
Cool but I'd like a bigger LCD screen, one that has the numbers BIG AND BOLD. Like a Dakota Digital or STACK dash.

mjiztight2345
09-15-2010, 08:17 AM
Please pm my information on how to get ahold of one of these. Since I know that you are very knowledgable, how do you integrate this with the EMU?

DrGonzo
09-15-2010, 10:57 AM
Please PM me info also if you would.

bubba army VR4
09-15-2010, 11:41 AM
PM please!

mh3kgt
09-15-2010, 12:06 PM
Interested in this as well. Pm me with more info...

Goallie11
09-15-2010, 12:12 PM
That is BAD ASS! Go ahead and pm me too.

CoopKill
09-19-2010, 11:55 PM
In for awesomeness

IPD
09-19-2010, 11:59 PM
*waits for full-color led/lcd with rotary readouts.

KeithMac
09-20-2010, 01:34 PM
Probably the best thing I`ve seen for our cars yet!.

Can you trigger an output for the knock warning? (I prefer a buzzer to flashing lights).

mb7050
09-20-2010, 05:20 PM
I want .

skyrunner
09-20-2010, 06:01 PM
Awesome project!

HLxDrummer
09-20-2010, 06:51 PM
PM me too! How do you scale the wideband/boost readings or do you need a set voltage per AFR/PSI? I'm also wondering if you can make it buzz.

BlackStealth
09-21-2010, 11:32 PM
After Ceddy brought my attention of MUToverOBD2 protocol on 95-96 DSM, I went ahead and researched this, purchased an ECU and got this protocol to work. I now can do MUToverOBD2, MUT, and OBD1 all from the same box. In short, every model supported. Our 3S cars 96+ will also work in MUToverOBD2 mode interestingly enough.

That was on my original checklist of things to do, "activate a remote buzzer". I'll have to check the microprocessor and see if there's any unused pins left to implement that wish. The priority of supporting a buzzer fell to low priority because it can already respond to two important things: 1. If there's knock, reduced the boost. 2. For water/alchy users if your fluid level goes low, it can trigger a latch to automatically reduce your boost to a pump gas friendly boost level and stay that way till next power cycle.

I don't think I understand your question in regards to "How do you scale wideband / Boost..." . It accepts any wideband o2 sensor output wire from 0-5 volts, and you just enter the low and high limits of the AFR and you're done.

I made a rough draft PDF format manual for it, anyone who's interested can email at blacklight99 at gmail.com and I'll send you a copy.

MR2
09-22-2010, 05:54 AM
your a nut :)

Vantage
09-22-2010, 08:59 AM
wow thats legit. +1

vr4tune
09-22-2010, 10:16 AM
What about aem ems users who no longer have a working obdii plug?

BlackStealth
09-22-2010, 03:24 PM
Okay I found an unused pin on the microprocessor and it can support a buzzer. The microprocessor can supply 5 volts DC with a maximum of 20mA of current. I looked at mouser and they have a bunch of buzzer's that can meet this requirement, so it looks like it's all possible. I'll go and update the software to support it. :)

As for AEM EMS owners, I could read the AEM EMS through the serial port and inquiry things from there. However, I'll need access to an AEM EMS to spy the serial port (or unless someone has this documented somewhere).

BlackStealth
09-22-2010, 06:43 PM
Done. It now supports a buzzer. I have it so that it turns on during three conditions. 1. Buzzing during an overboost event, shuts off buzzing when overboost is no longer, but the overboost message will continue flashing for a few moments longer. 2. Buzzing occurs only when the user defined KnockAlert threshold is exceeded, a Knock warning message will continue to flash afterwards for a short while. 3. If your tune is lean for the given boost and your knock exceeds 5 it will buzz you for 1 second and flash the message for short while thereafter.

In general I didn't want the buzzer to remain on if you fix the problem already thus giving the driver instant feedback.

GTOX
02-09-2011, 04:19 AM
Subscribed.

Sounds Great!

Mike-92RT
02-09-2011, 10:48 AM
WOWWWW... i want one of these!! lol

jba3
02-09-2011, 01:05 PM
I've been running one of these and giving feedback to BlackStealth for 4 or 5 months now on my DD. It's probably one of my favorite mods. I had my dad de-solder the MAP sensor from the board and connect some leads, so my MAP sensor sits in the engine bay right behind the plenum and just has 2 wires that run through the firewall to the control box.

I never noticed the random spots my car would knock. I *love* this boost controller. I can see knock on WOT sometimes and let off - and I bet my previous AVC-R was letting me just run right through the random knock. My car is also a 95, so I can confirm all the "hybrid" functionality - and I even got it to clear my forced CEL, which evoscan wouldn't do. :happydance:

If you don't have a boost controller, or you have a crappy one - you need this. And you can put a useful gauge in the stock boost gauge location.

Jesters Deadd
02-15-2011, 04:50 PM
Subscribed!

stealthTT
02-15-2011, 08:25 PM
subscribed!

3000GTCSULB
02-18-2011, 03:37 PM
subscribed!

Jesters Deadd
02-23-2011, 02:53 AM
I bought one of these. I'll post a short review of it when I get it installed.

stealthTT
02-23-2011, 07:34 AM
congrats!!
let us know how the install worked out.

Ilie

CoopKill
02-24-2011, 09:58 PM
I can't wait for the outcome!

RealMcCoy
02-24-2011, 10:30 PM
I have two of them sitting on top of my tool box that have yet to be installed... I have the cluster finished for mine, it looks pretty cool, but I haven't gotten around to actually installing it in the car yet. The other is for a customer, and his motor and trans are still scattered about the shop, so no hurry there. I have another customer whom I talked into buying one, he installed it himself and loves it.

CoopKill
02-24-2011, 11:04 PM
Has he mentioned any draw backs, or concerns?

P.S. Are you going to NG?

RealMcCoy
02-24-2011, 11:25 PM
Has he mentioned any draw backs, or concerns?

P.S. Are you going to NG?

I've only talked to him once since he installed it, but as far as I know, no issues at all... I'll make a point of asking him, I should hear from him tomorrow...

Don't think I'll be making N.G. this year...

Edit: I did one better, I just e-mailed him this link, hopefully he'll drop in and give his two cents...

bulta207
02-25-2011, 02:00 AM
It works very well. It has been in the car for about 2 months now. But I have not hooked up the boost controller yet. Install was not all that hard. I don't think I will go without one agine.

Goallie11
02-25-2011, 03:41 AM
Here's a pick of mine when I just finished installing it. I've had it for 4 months now and love it. There is an update he gave me for it that I have yet to install because I'm so lazy, but the only thing I would suggest is for it to datalog and be able to export to a laptop.

http://a8.sphotos.ak.fbcdn.net/hphotos-ak-snc4/39462_1530323056725_1194180456_31452787_3864277_n. jpg

BlackStealth
02-26-2011, 09:40 AM
Nice to see a photograph of the LCD in blue color (as my camera didn't take good pics of that color).

Rom3BreaK
02-26-2011, 10:27 AM
I've been watching this thread for a while, very cool! I agree, the only thing that this seems to be missing is a way to export data. This is a great solution for somebody like me; I rarely drive without my laptop logging what's going on.

PM with info please?

familyMAN
03-06-2011, 04:18 PM
How well does this control boost? Easy to dial out spikes while still holding target psi through revs? Has it been tested on larger than stock turbos?

Very interested. I want to ditch my mbc with my car's resurrection and love the idea of having the knock and afr warnings.

Has datalogging been added?

Goallie11
03-06-2011, 05:43 PM
No datalogger yet, I don't know how frequently he works on it, and he is the only one that works on it so it may be a while. I'll email him and ask if he can incorporate it.

The interface for the boost controller is almost identical to the profec b spec 2, and I think it works pretty well. I've got bigger turbos, but i havent maxed them or anything yet, but it definitely does work on them.

Chris GTO TT
03-06-2011, 05:59 PM
Doesn't the Serial out allow you to plug in your logger?

green-lantern
03-06-2011, 06:08 PM
I'm not sure if I missed this thread before or I just meant to come back and check it out later but this thing is very cool.

BlackStealth
03-06-2011, 07:05 PM
The serial datalogging port is for interfacing a dataloging cable to it, so the unit can read ECU information. The unit can display the ECU datalog information to the screen, but not export it.

Having had a greddy profec B spec II boost controller, I used the familiar duty cycle approach for controlling boost. Higher the duty cycle, higher the boost. On my car, I had problems with boost falling off 2psi at high RPMS, so added a feature to fix this problem. I called it "Dutycycle offset", and at 4000, 4500, 5000, 5500, etc... RPM intervals you can add additional duty cycle to compensate this common problem, giving you a linear boost all the way across.

Another advance boost control feature is to temporarily reduce boost when your engine is knocking. This is user definable, you control how much duty cycle is reduced when knock is present.

I use this boost controller to regulate boost at 18psi for my 15G class turbos.

green-lantern
03-06-2011, 07:14 PM
Will the greddy solenoid work with this?

Goallie11
03-06-2011, 07:30 PM
The reducing boost because of knock feature is really great, something all boost controllers should have.

Can you work on it exporting logs Antero?

Lugnut
03-06-2011, 07:37 PM
... pfffth ...

BlackStealth
03-06-2011, 07:44 PM
The greddy boost solenoid should work because it's very similar to the AEM/mac valve solenoid.

To export datalog information would require additional hardware. I could make a daughtercard that sits in between the microprocessor and the socket to add new capabilities, I'm just flirting with the idea on how to go about it.

Chris GTO TT
03-06-2011, 11:19 PM
Just ordered one cant wait!

TonyM
03-07-2011, 10:24 AM
Man this thing is cool. May need to go on my to do list for the summer . . .

Goallie11
03-07-2011, 08:07 PM
I took another pic for you guys so you can see it with the bezel put back on.

http://img.photobucket.com/albums/v653/Goallie11/IMAG00102.jpg?1299542763

CoopKill
03-07-2011, 10:04 PM
Can I ask if there is something in the way to prevent centering the gauge with the rpm writing?

I want this as well, but am doing other more important things and want to wait for logging output capabilities...

Goallie11
03-07-2011, 10:55 PM
You could move it over a little more, but the actual screen is bigger then the bit you can see, the electronics of it that is.

Sidenote: Antero I think you should make a little positioning template so the screen can be properly aligned instead of having to measure a whole bunch and still miss. (Like I did, but not by a noticeable amount.)

BlackStealth
03-07-2011, 11:00 PM
There's a piece of clear plastic in the way that would have to be grinded down or cut to center it properly. This clear plastic is responsible for distributing the light evenly. I did have it centered on my first attempt, but it takes more effort to do that. On my second attempt I got lazy and left the clear plastic alone, which is why it's not centered. So yes, it can be done, but more work.

92pearltt
03-24-2011, 05:58 AM
this has got to be one of the best things made for our cars.

tabasco122
03-25-2011, 04:04 AM
subscribed. curious to see if this will work on other obd1 cars.

vr4tune
03-25-2011, 09:35 AM
Any news for aem users yet? Your killing me! Please integrate with aem ems!

BlackStealth
03-25-2011, 09:53 AM
The OBD1 I implemented is "Mitsubishi OBD1" such as Stealth/3000GT/Talon/Eclipse/Laser/Galant/etc. Other OBD1 can only be added in if I had documentation for it.

AEM EMS - Same thing, need documentation. I made a serial port sniffer, just need an AEM EMS to play with.

green-lantern
03-25-2011, 04:43 PM
Can I ask if there is something in the way to prevent centering the gauge with the rpm writing?

I want this as well, but am doing other more important things and want to wait for logging output capabilities...

You have to cut the clear plastic piece in back. Here is mine

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8803.jpg

STLVR4
03-25-2011, 04:54 PM
I want this.

How do I get it?

vr4z06
03-25-2011, 06:28 PM
I just have to say that you are one awesome dude to take the time to imagine, design, develop and produce this device!!!
KUDOS to you! this is so frikkin overdue and you have made it a reality...
If only it was setup for AEM! So ready!!!
THANKS for taking the time and effort to make it a reality!

Chris GTO TT
03-26-2011, 03:20 PM
I want this.

How do I get it?

Send a PM to BlackStealth saying you'd like to buy one...he will respond with pricing and info :dontknow:

BlackStealth
03-26-2011, 06:56 PM
You have to cut the clear plastic piece in back. Here is mine

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8803.jpg

Looks like you did a good job getting it centered. Looking good.

All others: I'm all sold out, and working on a new design. Maybe I'll have an update in about a month.

rawavr4
03-26-2011, 08:09 PM
Pm sent regarding price. I might replace my SM3 and get a boost controller if I'm lucky.

CoopKill
03-26-2011, 08:17 PM
If I get my AEM soon I will PM you about sending it for R&D.

hated
03-26-2011, 08:18 PM
IN to follow for new design.

green-lantern
03-26-2011, 09:13 PM
Looks like you did a good job getting it centered. Looking good.


Thanks man, and thanks for making it.

rawavr4
03-26-2011, 09:31 PM
Where is the boost controller knob located? The one mentioned in the beginning of the thread

BlackStealth
03-27-2011, 09:18 AM
The knob is on a wire, you have to be creative on where you want to locate yours. Perhaps 2nd generation cars with an unused popup headlight button could locate theirs there. On my 1st generation car mine is located near the cruise control switch. My neighbor installed his knob and display on an unused radio slot.

Goallie11
03-27-2011, 02:12 PM
Yeah near the cruise control area, or for me closer to the passenger side is where I have mine. It's easy to reach down there if you have your hand resting on the shift knob.

What's the new project Blackstealth?

BlackStealth
03-27-2011, 06:21 PM
Everyone has been asking for datalogging capabilities, so I switched to a different microprocessor to make this happen. I'll have to wait a few weeks for my circuit boards to come in so I can test the new design out.

familyMAN
03-27-2011, 06:27 PM
Everyone has been asking for datalogging capabilities, so I switched to a different microprocessor to make this happen. I'll have to wait a few weeks for my circuit boards to come in so I can test the new design out.

Awesome! Keep us updated. Definitely thinking of getting one for my rebuild. Love the idea of knock monitoring and boost reduction.

Tiberius
03-27-2011, 07:37 PM
subscribed

green-lantern
03-27-2011, 07:51 PM
Everyone has been asking for datalogging capabilities, so I switched to a different microprocessor to make this happen. I'll have to wait a few weeks for my circuit boards to come in so I can test the new design out.

Damn mine is outdated already! lol I was hoping this would be a software update. :sad:

Chris GTO TT
03-27-2011, 08:24 PM
Damn mine is outdated already! lol I was hoping this would be a software update. :sad:

:stupid:

Street_Chally73
03-27-2011, 09:26 PM
That is awesome!!! Very nice work with developing this & its fit & finish looks amazing!!!

BlackStealth
03-27-2011, 10:40 PM
I'll offer an upgrade to existing customers when the new design is thoroughly tested and sell it at near cost to be fair. I've listened to what you guys wanted, and made datalogging now possible. The main board now accepts a small daughterboard expansion. This expansion allows me to offer three different kinds of datalogging: (1) serial cable, (2) bluetooth or (3) SD card datalogging.

CoopKill
03-27-2011, 10:54 PM
Nice!

green-lantern
03-27-2011, 11:02 PM
I'll offer an upgrade to existing customers when the new design is thoroughly tested and sell it at near cost to be fair. I've listened to what you guys wanted, and made datalogging now possible. The main board now accepts a small daughterboard expansion. This expansion allows me to offer three different kinds of datalogging: (1) serial cable, (2) bluetooth or (3) SD card datalogging.

You are the fucking man! Sounds great!

Chris GTO TT
03-27-2011, 11:34 PM
I'll offer an upgrade to existing customers when the new design is thoroughly tested and sell it at near cost to be fair. I've listened to what you guys wanted, and made datalogging now possible. The main board now accepts a small daughterboard expansion. This expansion allows me to offer three different kinds of datalogging: (1) serial cable, (2) bluetooth or (3) SD card datalogging.

Bluetooth! NICE!

GTOJOE
03-28-2011, 10:16 AM
In for specs of Ver.2

Goallie11
03-28-2011, 12:45 PM
Awesome! If you could make the bluetooth logging compatible with Memphetic's mmcd for android that would be incredible!

Jesters Deadd
03-28-2011, 02:05 PM
2568256925702571

I was hoping to be the first to think of using the old popup headlight button for the rotary dial. Oh well. It took me two weekends to do this install because I ordered an extra set of switches from a 93 3S. I also used the ECS button for my AUX push for boost button. I love this button setup. I plan to change the covers of the two buttons to something different. The old popup headlight actually fits snuggly over the little knobs with very little modification.

3000GTCSULB
03-28-2011, 02:19 PM
Awesome! If you could make the bluetooth logging compatible with Memphetic's mmcd for android that would be incredible!

That would be awesome...I made the mistake of buying his software with no hardware available yet. Live and learn I guess.

Goallie11
03-28-2011, 02:32 PM
That would be awesome...I made the mistake of buying his software with no hardware available yet. Live and learn I guess.

Man I didn't know he was charging for it, 20 is quite steep especially if he plans on charging 100 for the adapter like last I heard.

tabasco122
03-28-2011, 02:34 PM
I'm super excited about this. He is adapting it for use with nissan obd1 vehicles also (for me :-)) You guys are lucky, you have a scanmaster, the 240 crowd has nothing like this available. I cant wait for that version 2 to become available.

green-lantern
03-28-2011, 04:52 PM
2568256925702571

I was hoping to be the first to think of using the old popup headlight button for the rotary dial. Oh well. It took me two weekends to do this install because I ordered an extra set of switches from a 93 3S. I also used the ECS button for my AUX push for boost button. I love this button setup. I plan to change the covers of the two buttons to something different. The old popup headlight actually fits snuggly over the little knobs with very little modification.

Your install looks great! I think yours in the exact same spot. You used that line and the dummy lights to keep it straight right? It looks like your knob is in the same spot also. Your cut looks cleaner than mine though. How did you cut it?

BlackStealth
03-28-2011, 04:58 PM
2568256925702571

I was hoping to be the first to think of using the old popup headlight button for the rotary dial. Oh well. It took me two weekends to do this install because I ordered an extra set of switches from a 93 3S. I also used the ECS button for my AUX push for boost button. I love this button setup. I plan to change the covers of the two buttons to something different. The old popup headlight actually fits snuggly over the little knobs with very little modification.

When you get it all done it would be cool if you can make a short video demonstrating the rotary dial (old popup headlight button). Cool idea on using the ECS for AUX boost switch. I love hidden switches. :)

Jesters Deadd
03-28-2011, 06:11 PM
Your install looks great! I think yours in the exact same spot. You used that line and the dummy lights to keep it straight right? It looks like your knob is in the same spot also. Your cut looks cleaner than mine though. How did you cut it?

I did use the dummy lights! haha. I just used a new razor blade, a small metal T -square and ready took my time.

Jesters Deadd
03-28-2011, 06:15 PM
When you get it all done it would be cool if you can make a short video demonstrating the rotary dial (old popup headlight button). Cool idea on using the ECS for AUX boost switch. I love hidden switches. :) I love hidden switches too! An ECS switch works perfect. Plus as a bonus, I am wiring in the not used "Sport" gauge light for the non installed ECS to the switch too. So I will know when it is on and off. Haha! I like indicators too!

green-lantern
03-28-2011, 07:23 PM
I did use the dummy lights! haha. I just used a new razor blade, a small metal T -square and ready took my time.

I thought you did lol, your cut just looks a bit cleaner.

Mine didn't have the rotary dial it was just a blank so I cut a round piece of plastic to slip in there and the stock switch holds it down so I didn't have to glue it.

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8812.jpg

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8813.jpg

My clear plastic piece must have got some windex on it or something. That's as clean as I could get it. It didn't seem to bother me in the car though so I hope it won't when I put it back in.

CoopKill
03-28-2011, 11:30 PM
Nice install guys!

Is that light beer Paul?:w00t:

green-lantern
03-29-2011, 12:20 AM
Yes, I'm a Mic Ultra fan :redface:

I am drinking a Fat Tire right now though. ha ha I'm really just a fan of all alcohol.

CoopKill
03-29-2011, 12:47 AM
Both fine examples!
Yes, I'm a Mic Ultra fan :redface:

I am drinking a Fat Tire right now though. ha ha I'm really just a fan of all alcohol.





__________________________________________________ ____________________

Tapatalk Bitches! :transform:

FastOldGuy
03-29-2011, 11:42 PM
When this works with an AEM ECU I will buy one so put me on the list. :)

vr4tune
03-30-2011, 03:06 PM
Still want aem compatibility!

green-lantern
03-30-2011, 03:36 PM
When this works with an AEM ECU I will buy one so put me on the list. :)

Like the remote on your TV set, you will have to get your kid to show you how to use it, you old fart. :p

Jesters Deadd
03-31-2011, 03:44 PM
Has anyone seen any bugs with this?

Simace
03-31-2011, 04:04 PM
What would really take this product over the edge would be if it was able to display not on the instrument cluster but on the Windshield, like a HUD (Heads Up Display). I know that this would require dashboard work, but the end result would be something absolutely astounding!! Not that it isn't already.

Subscribed...

BlackStealth
03-31-2011, 04:05 PM
Has anyone seen any bugs with this?
If there is, let me know. I squash all bugs ASAP.

BlackStealth
03-31-2011, 04:07 PM
What would really take this product over the edge would be if it was able to display not on the Guage Cluster but on the Windshield, like a HUD (Heads Up Display). I know that this would require dashboard work, but the end result would be something absolutely astounding!! Not that it isn't already.

Subscribed...
A HUD requires a special windshield (special coating). I can see that getting expensive pretty quick.

green-lantern
03-31-2011, 04:52 PM
What would really take this product over the edge would be if it was able to display not on the instrument cluster but on the Windshield, like a HUD (Heads Up Display). I know that this would require dashboard work, but the end result would be something absolutely astounding!! Not that it isn't already.

Subscribed...

That would be awesome.

Jesters Deadd
03-31-2011, 05:07 PM
ok, bugs...
car 1999 VR4
Issue 1: The rear trim and rear low seem to be switched. When I go to the rear trim menu to watch live info, the low setting is moving all over the place. the rear trim setting is acting like the low should be. The front trim setting seem to work correctly. The rear low will also go as high as 199. Shouldn't the trims and low mid high only go to 150? what is the max reading for these?

Jesters Deadd
03-31-2011, 05:09 PM
bugs...
car 1999 VR4
Issue 2: My car will get a CEL and I try to check the trouble code and it always comes back no messages in both the active faults and stored faults. The clear all messages works fine.

tabasco122
03-31-2011, 05:27 PM
A HUD requires a special windshield (special coating). I can see that getting expensive pretty quick.

Some 240s have a hud, they have what appears to be a sticker on the front corner. The defi would be cool to use if it could be adapted...

BlackStealth
03-31-2011, 05:31 PM
I recently installed a 99 3000GT VR4 ECU into my 93 Vehicle and took it for a spin a few minutes ago. I decided to check out how the CEL codes worked and observed the same thing, the CEL would come on during the test. I'm pretty sure I know what it is already because I asked the ECU to perform a diagnostic test before pulling codes on 94-99 model cars. I'll just skip that forced diagnostic test and see what happens.

You could be right on the rear trim thing, I asked one person to give me feedback if it was working and they said it looked correct. It is very likely what you said, "Trim and Low fuel trim are mixed up". Fuel trims usually go between 80-140 I think, and the trim by itself has a much wider range.

Send me your email address in PM and I'll give you an update.

Jesters Deadd
03-31-2011, 06:07 PM
Oh i was also in the config menu and there is a coolant alarm and another setting at the end of the menu that you didn't have in your user manual. What do those two settings do?

Jesters Deadd
03-31-2011, 06:09 PM
I recently installed a 99 3000GT VR4 ECU into my 93 Vehicle and took it for a spin a few minutes ago. I decided to check out how the CEL codes worked and observed the same thing, the CEL would come on during the test. I'm pretty sure I know what it is already because I asked the ECU to perform a diagnostic test before pulling codes on 94-99 model cars. I'll just skip that forced diagnostic test and see what happens.

You could be right on the rear trim thing, I asked one person to give me feedback if it was working and they said it looked correct. It is very likely what you said, "Trim and Low fuel trim are mixed up". Fuel trims usually go between 80-140 I think, and the trim by itself has a much wider range.

Send me your email address in PM and I'll give you an update.

What did you do about the second set of O2 sensors in your 99 ECU?

BlackStealth
03-31-2011, 06:25 PM
The manual gets updated when new features get added. The coolant alarm alerts you when your engine coolant temperature exceeds this number, similar idea to knock alert. This could be useful those with large front mount intercoolers and have overheating issues, this will remind them. The "Screen Refresh" allows you to define how often the screen updates with new data. Think of it as a delay, the higher the number the less frequently it is updated. Similarly the lower the number, more often the data is refreshed with new data.

I haven't driven the 99 ECU swap very much to see an error yet, but I'm expecting to see a CEL error for it soon. I'm going to disable the second set of O2s if it's available in the ECU-flashing software. If it's not in there, I can build an O2 simulator for it.

Jesters Deadd
03-31-2011, 07:25 PM
The manual gets updated when new features get added. The coolant alarm alerts you when your engine coolant temperature exceeds this number, similar idea to knock alert. This could be useful those with large front mount intercoolers and have overheating issues, this will remind them. The "Screen Refresh" allows you to define how often the screen updates with new data. Think of it as a delay, the higher the number the less frequently it is updated. Similarly the lower the number, more often the data is refreshed with new data.

I haven't driven the 99 ECU swap very much to see an error yet, but I'm expecting to see a CEL error for it soon. I'm going to disable the second set of O2s if it's available in the ECU-flashing software. If it's not in there, I can build an O2 simulator for it.

I think the coolant warning is a great idea. And the refresh rate thing too. So the smaller the number the faster it refreshes.

Goallie11
03-31-2011, 09:30 PM
I have a CEL also that it doesn't read. But I used mmcd to try reading it also, and it doesn't show anything either so I doubt it's a bug in your software.

BlackStealth
03-31-2011, 09:49 PM
The software is very well tested on OBD1 cars because that's what I had. There are some minor differences when using MUT, so it is possible for some minor errors to exist. Also now that I have 99 ECU I can test it much more thoroughly and not have to rely on others for feedback.

As for error codes, I can only test for ECU error codes. If you have ABS, Cruise control, or ECS errors those cannot be checked because the datalogging cable only connects to the ECU pin.

CoreyB
04-01-2011, 01:45 PM
Did every ones "H" and "E" keys get swapped? Whats going on with all teh "teh" talk. teh teh teh

Alan you bastard

jba3
04-03-2011, 08:32 PM
Damn mine is outdated already! lol I was hoping this would be a software update. :sad:

If all goes like it was planned for months ago, you don't need to buy a new LCD screen, rotary, map sensor, solenoid, etc. It'll be a drop-in swap for the main brain and good to go.


I thought you did lol, your cut just looks a bit cleaner.

Mine didn't have the rotary dial it was just a blank so I cut a round piece of plastic to slip in there and the stock switch holds it down so I didn't have to glue it.

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8812.jpg

http://i123.photobucket.com/albums/o310/hptech4564/AWD%20conversion/DSCF8813.jpg

My clear plastic piece must have got some windex on it or something. That's as clean as I could get it. It didn't seem to bother me in the car though so I hope it won't when I put it back in.

That came out WAY cool! My first attempt was gluing the rotary knob to a "blank" button around the bezel that I cut, but there wasn't enough surface area on the rotary to glue. I need to pick up a rotary cover. :o


Has anyone seen any bugs with this?


If there is, let me know. I squash all bugs ASAP.

Agreed on this; I did some early testing and requests/comments and he responded quickly with a new version of the software to upload. :)


bugs...
car 1999 VR4
Issue 2: My car will get a CEL and I try to check the trouble code and it always comes back no messages in both the active faults and stored faults. The clear all messages works fine.

Try it with the key on, and engine off. I got random code reads while the car was running, and it wouldn't clear the codes. With the key on and car off, it read the code fine, then cleared it, and it stayed off. Mine's a 95, but it's worth a shot....


Some 240s have a hud, they have what appears to be a sticker on the front corner. The defi would be cool to use if it could be adapted...

A friend had a HUD setup on his evo. The little windshield sticker type. It's possible, but it's by no means "easy" or "cheap". I think his setup was around $1k.


I recently installed a 99 3000GT VR4 ECU into my 93 Vehicle and took it for a spin a few minutes ago. I decided to check out how the CEL codes worked and observed the same thing, the CEL would come on during the test. I'm pretty sure I know what it is already because I asked the ECU to perform a diagnostic test before pulling codes on 94-99 model cars. I'll just skip that forced diagnostic test and see what happens.

You could be right on the rear trim thing, I asked one person to give me feedback if it was working and they said it looked correct. It is very likely what you said, "Trim and Low fuel trim are mixed up". Fuel trims usually go between 80-140 I think, and the trim by itself has a much wider range.

Send me your email address in PM and I'll give you an update.

Yep, it looked right to me on my 95 VR4, stock ECU, stock injectors/fuel setup, etc, so it should never be TOO far off with mostly stock. Since it reads from the OBD port for the device, I couldn't simultaneously log and check the screen display.

Jesters Deadd
04-04-2011, 08:01 PM
Quick question, If i was going to use the stock wiring for the new solenoid, which wire would/could I hook up the old ECU wastegate solenoid wire to. The ECU would ground the solenoid and the MFI relay would power it. I am not sure if the boost controller modulates the positive or modulates the ground to the solenoid. THanks

BlackStealth
04-04-2011, 11:50 PM
Quick question, If i was going to use the stock wiring for the new solenoid, which wire would/could I hook up the old ECU wastegate solenoid wire to. The ECU would ground the solenoid and the MFI relay would power it. I am not sure if the boost controller modulates the positive or modulates the ground to the solenoid. THanks

Sounds rather risky what you're doing, especially if you're unsure of yourself. My boost controller feeds 12 volts to the boost solenoid, and then pulses the ground as needed for pulse-width-modulation. If you want to re-use stock wiring, you'll need to find two free unused wires. Personally I'd just use the boost solenoid wire I provided since it's automotive grade, correct awg, and thin enough to fit through the firewall.

Jesters Deadd
04-05-2011, 01:08 AM
Sounds rather risky what you're doing, especially if you're unsure of yourself. My boost controller feeds 12 volts to the boost solenoid, and then pulses the ground as needed for pulse-width-modulation. If you want to re-use stock wiring, you'll need to find two free unused wires. Personally I'd just use the boost solenoid wire I provided since it's automotive grade, correct awg, and thin enough to fit through the firewall.
Maybe you are misunderstood me. Since I'm not using the stock wastegate solenoid I am going to remove it. But that leaves me the wastegate solenoid wire from the stock ECU. It sounds like your boost controller works the same as the stock ECU. So all I have to do is hook up the old stock wastegate solenoid wire to my new solenoid and hook up the other end to your boost controller black solenoid wire. The wire guage is fine and already routed. I'll let you know how it works when I get it working.

NickS VR4
04-05-2011, 05:43 AM
I am not very electronically inclined ATM, but would it be possible to have the dummy lights tied into this. For example, if the door is open, it will have a "Door Ajar" notification displayed. Same thing with "Brake", "Low Wiper Fluid", etc.

BlackStealth
04-05-2011, 09:53 AM
Maybe you are misunderstood me. Since I'm not using the stock wastegate solenoid I am going to remove it. But that leaves me the wastegate solenoid wire from the stock ECU. It sounds like your boost controller works the same as the stock ECU. So all I have to do is hook up the old stock wastegate solenoid wire to my new solenoid and hook up the other end to your boost controller black solenoid wire. The wire guage is fine and already routed. I'll let you know how it works when I get it working.
Here's extra info on the boost solenoid harness: The red and black color wires do not have any meaning. You'll have to use a meter to determine which color wire is 12 volts, so don't make any assumptions. One wire provides a constant 12volts, and the other wire pulses ground when the solenoid is active. What you're doing can be done, just be careful and don't make any mistakes. Also the "stock boost solenoid wire" is wired to the ECU, cut this wire please. You have to make sure you're not sharing the "stock boost solenoid wire" with anything else other than my boost controller.

BlackStealth
04-05-2011, 09:55 AM
I am not very electronically inclined ATM, but would it be possible to have the dummy lights tied into this. For example, if the door is open, it will have a "Door Ajar" notification displayed. Same thing with "Brake", "Low Wiper Fluid", etc.
Yes I could do that, but I'm not sure how many people would want that, as there would be a lot of wire splicing involved.

NickS VR4
04-05-2011, 12:29 PM
Yes I could do that, but I'm not sure how many people would want that, as there would be a lot of wire splicing involved.

Maybe once I get my project off the ground, it will be wanted more, maybe not.

Jesters Deadd
04-05-2011, 04:08 PM
Try it with the key on, and engine off. I got random code reads while the car was running, and it wouldn't clear the codes. With the key on and car off, it read the code fine, then cleared it, and it stayed off. Mine's a 95, but it's worth a shot....


I tried it with the key on, and engine off. I got nothing. I tried it running and got nothing. But it would always clear the code and turn off the CEL. It is an emisson code that keeps coming up. I should try my ECUflash code reader on it to see what it reads.

Jesters Deadd
04-05-2011, 04:25 PM
Here's extra info on the boost solenoid harness: The red and black color wires do not have any meaning. You'll have to use a meter to determine which color wire is 12 volts, so don't make any assumptions. One wire provides a constant 12volts, and the other wire pulses ground when the solenoid is active. What you're doing can be done, just be careful and don't make any mistakes. Also the "stock boost solenoid wire" is wired to the ECU, cut this wire please. You have to make sure you're not sharing the "stock boost solenoid wire" with anything else other than my boost controller.
I planned on cutting the wire to the ECU. FYI my manual says its pin 41 on the middle plug. Thanks for the info on the solenoid plug.

Jesters Deadd
04-05-2011, 04:29 PM
Maybe once I get my project off the ground, it will be wanted more, maybe not.

I am connecting my "push for boost" button with the old sport gauge light that is used for the ECS. Since my car is a 99 it never had ECS so I am putting a bulb in the open spot and attaching it to my button. So when the button is latched it will light up sport on the gauge. when it is off it will go black.

BlackStealth
04-06-2011, 04:02 PM
Jesters Deadd: I like your clever "push for boost" button idea. :)

I learned a bit more on the rear fuel trims:
94/95 ECU request codes differ from 98/99 ECU request codes. Gatecrasher was kind enough to send me a private message with the 98/99 request codes, I'll test them out just as soon as it stops raining outside.
My LCD boost controller can read the "ecu id" during a MUT initialization and automatically send the correct request ID because it knows the year of the car. Now I just need a short list of corresponding "ecu id" to year model of the car to make this happen.

I have access to the 99 3000GT VR4 and 94 RT/TT "ecu id", I just need to find out a few more, such as the 95,96,97,98 ECU id. Evoscan spits out this information when it connects.

94 Stealth RT/TT -- ECUID=E6A1
99 3000GT VR4 -- ECUID=E6AE

Jesters Deadd
04-06-2011, 04:08 PM
Jesters Deadd: I like your clever "push for boost" button idea. :)

I learned a bit more on the rear fuel trims:
94/95 ECU request codes differ from 98/99 ECU request codes. Gatecrasher was kind enough to send me a private message with the 98/99 request codes, I'll test them out just as soon as it stops raining outside.
My LCD boost controller can read the "ecu id" during a MUT initialization and automatically send the correct request ID because it knows the year of the car. Now I just need a short list of corresponding "ecu id" to year model of the car to make this happen.

I have access to the 99 3000GT VR4 and 94 RT/TT "ecu id", I just need to find out a few more, such as the 95,96,97,98 ECU id. Evoscan spits out this information when it connects.

Hells yea! Were you able to read your trouble codes on your ECU?

BlackStealth
04-06-2011, 07:45 PM
I just tested the new codes for the rear trims and it seems to be giving good numbers (very similar to front trims). When I took a longer trip the other day I received my first CEL as expected, as my 3rd and 4th O2 sensors are not available on my car. When I scanned for the CEL I got nothing, although that doesn't really surprise me because it can only report 16 types of errors (using the older Mitsu error code list). I think I may have to connect in OBD2 mode to view error codes. I tried using evoscan and it said nothing. My CEL isn't even lit up anymore. I'll try again when it lights up.

Jesters Deadd
04-07-2011, 01:12 PM
Hey what does the psi start and psi end settings do?
And what are your duty cycle settings and boost creep settings set at?

Jesters Deadd
04-07-2011, 01:14 PM
I just tested the new codes for the rear trims and it seems to be giving good numbers (very similar to front trims). When I took a longer trip the other day I received my first CEL as expected, as my 3rd and 4th O2 sensors are not available on my car. When I scanned for the CEL I got nothing, although that doesn't really surprise me because it can only report 16 types of errors (using the older Mitsu error code list). I think I may have to connect in OBD2 mode to view error codes. I tried using evoscan and it said nothing. My CEL isn't even lit up anymore. I'll try again when it lights up.
What if you go to autozone or somewhere and get free scan from them? Does anything come up?

Goallie11
04-07-2011, 03:03 PM
Autozone and Oreilly's can't check ODBI, I just went the other day and neither had the plugs to do it, so I'll have to go to a dealer and see.

BlackStealth
04-07-2011, 04:01 PM
Someone asked for improved turbo spool up so I created "PSI start" and "PSI end". Let's assume 50% duty cycle gives us 15psi and this is our desired boost level. Anything above the 50% duty cycle line will improve the turbo spoolup. In the ideal world we would switch from 100% duty cycle to 50% duty cycle when we reached 15psi, but of course in the real world wastegates can't react that fast and would cause a major boost spike. Instead what we need to do is ramp down to our desired boost level to avoid a boost spike, this way we can enjoy the improved turbo spoolup without any side effects.

http://i782.photobucket.com/albums/yy107/blackstealth_2009/PSIStartPSIEnd.gif

On my car I experience some boost loss at high rpms -- probably because I'm still using a stock catback. Here's my settings for compensating the loss:

Duty Cycle OFFSET:
4000 +0
4500 +0.6
5000 +1.3
5500 +2.0
6000 +2.6
6500 +3.3
7000 +4.0
7500 +4.0
8000 +4.0

I currently don't have a CEL light at the moment, I'm waiting for it to return before I can test for it again.

Jesters Deadd
04-08-2011, 10:49 AM
Hey just an update. I used the stock wiring... works great. And there is two less new wires in the engine bay. :) the ECS button conversion for "push for boost" works great. I love this thing!

Jesters Deadd
04-08-2011, 10:50 AM
I currently don't have a CEL light at the moment, I'm waiting for it to return before I can test for it again.

Do you have your emission stuff all hooked up? Ie: EGR and Evap?

BlackStealth
04-08-2011, 03:14 PM
Do you have your emission stuff all hooked up? Ie: EGR and Evap?
Yes I do, but I don't have the 3rd and 4th O2 sensors so I should be getting a CEL for that. The old Mitsu error chart doesn't have a code for those extra O2 sensors because it only lists 16 possible faults, so I'm assuming the CEL can only be read through OBD2.

Goallie11
04-08-2011, 07:04 PM
I just went to the mitsu dealer to have my code checked and spend $86 to learn that it was a front o2 sensor code, which I had suspected seeing how it's cut. So this is definitely something the unit should have read, but it couldn't for some reason.

TwIzTeD_3kGt
04-08-2011, 07:20 PM
Looks like I'm late to the party, but this is one of the coolest things I've ever seen. Nice work!

FastOldGuy
04-08-2011, 07:46 PM
AEM Compatibility please.

BlackStealth
04-09-2011, 08:42 AM
I just went to the mitsu dealer to have my code checked and spend $86 to learn that it was a front o2 sensor code, which I had suspected seeing how it's cut. So this is definitely something the unit should have read, but it couldn't for some reason.
That's strange seeing how you have OBD1 as I was able to pull codes on my 93 RT/TT when I tested it -- I'll look into it further.

3000GT MR
04-09-2011, 09:03 AM
I have a weird issue with mine. Anytime I go wot it turns off and reboots almost at a certain throttle position. Even if I'm in 6th gear and mash it at 30mph it still does it. I have litteraly checked everything with no faults found. Another is when I go to read or delete codes it freezes until I reboot it. I have a 94 hybrid

Goallie11
04-09-2011, 05:04 PM
That's strange seeing how you have OBD1 as I was able to pull codes on my 93 RT/TT when I tested it -- I'll look into it further.

Thanks, I used to be able to read codes on it so maybe updating it to the newest version caused the error?

BlackStealth
04-09-2011, 06:49 PM
I have a weird issue with mine. Anytime I go wot it turns off and reboots almost at a certain throttle position. Even if I'm in 6th gear and mash it at 30mph it still does it. I have litteraly checked everything with no faults found.

The 94 and beyond are susceptible to noise on the MUT cable. This noise triggers a reboot. To rid of this problem once and for all, you should completely clip off this yellow capacitor as shown in this diagram. It's only purpose was to automatically reset the boost controller as a convenience when reprogramming. You can still reprogram the boost controller with it removed, so don' worry about it's absence. I've completely removed it from the newer design.
http://i782.photobucket.com/albums/yy107/blackstealth_2009/clipCapacitor.jpg


Another is when I go to read or delete codes it freezes until I reboot it. I have a 94 hybrid
Which software version are you using? We're currently at v1.7, and v1.8 is in testing.

BlackStealth
04-09-2011, 07:36 PM
Thanks, I used to be able to read codes on it so maybe updating it to the newest version caused the error?
I made the assumption that MUT was standard throughout 94-99 cars and I made some changes to it when someone asked. Apparently that caused problems that I'm investigating.

I re-examined the OBD1 (91-93) CEL request routine and I find no errors. I wonder how the dealer was able to tell you it was the front O2 sensor because the Mitsu CEL error chart is very generic "Oxygen failure", and it doesn't tell you if it is the front or rear or heater circuit. Did you try both "Active" and "Stored" tests?

3000GT MR
04-10-2011, 12:32 AM
Thanks blackstealth. Ill have to check myversion. Where exactly have you been posting the update software?

Goallie11
04-10-2011, 03:56 AM
I made the assumption that MUT was standard throughout 94-99 cars and I made some changes to it when someone asked. Apparently that caused problems that I'm investigating.

I re-examined the OBD1 (91-93) CEL request routine and I find no errors. I wonder how the dealer was able to tell you it was the front O2 sensor because the Mitsu CEL error chart is very generic "Oxygen failure", and it doesn't tell you if it is the front or rear or heater circuit. Did you try both "Active" and "Stored" tests?

Yeah I tried both active and stored and neither showed anything. I don't know how they were able to tell it was a front o2 sensor unless he actually looked at it and saw it clipped. I've always seen it as just 02 sensor as well.

BlackStealth
04-11-2011, 10:06 AM
Updates can be downloaded from "www.lcdboostcontroller.com". It's a "simple" website I made that gives us an easy way to download updates from now on. Thanks goes to tabasco122 for making this possible.

I finally got a CEL on my 99 3000GT ECU so I could test it. I learned that the MUT communication mode is unable to read CEL codes and I had to go to OBD2 communication mode to read it. Now that I know this is the case, I'll make the necessary software changes.

Jesters Deadd
04-11-2011, 01:31 PM
Updates can be downloaded from "www.lcdboostcontroller.com". It's a "simple" website I made that gives us an easy way to download updates from now on. Thanks goes to tabasco122 for making this possible.

I finally got a CEL on my 99 3000GT ECU so I could test it. I learned that the MUT communication mode is unable to read CEL codes and I had to go to OBD2 communication mode to read it. Now that I know this is the case, I'll make the necessary software changes.

cool!

Jesters Deadd
04-11-2011, 01:32 PM
I think you should come up with a better name for your product... just saying.

jba3
04-11-2011, 02:40 PM
I tried it with the key on, and engine off. I got nothing. I tried it running and got nothing. But it would always clear the code and turn off the CEL. It is an emisson code that keeps coming up. I should try my ECUflash code reader on it to see what it reads.

I was running version 1.6 - not sure if that matters or not. I'll be upgrading to 1.8 this week.

EDIT: BlackStealth, I'd be interested in it displaying misc things instead of/in addition to the "dummy" lights.

tabasco122
04-11-2011, 03:08 PM
black stealth innovations
black stealth designs

BlackStealth
04-14-2011, 01:33 PM
Update: On firmware1.9, I managed to read stored DTC codes on my 99 3000GT VR4 ECU. I only get 9 errors, but when I use Evoscan it shows an additional 2 more errors. I'm a bit puzzled as to why this is so, I'm speculating Evoscan is including "pending DTC" with the stored DTC codes. I'll resume testing when the rain storm passes.

vr4tune
04-14-2011, 09:10 PM
Aem would be nice!:poke:

BlackStealth
04-15-2011, 08:45 AM
My car started stumbling really bad yesterday during a drive to the store and I was puzzled as to what the cause was. My front fuel trims went really lean (50) and my rear fuel trims showed very rich (150). Next I noticed there was no activity on the rear O2 sensor. Bingo, my rear O2 sensor died. My front O2 sensor died two years earlier and as a quick fix I substituted it with the narrow band O2 simulation from my WBO2 located in the collector. Having instant data access to the ECU certainly has come handy as my car gets older. I've solved two problems with it so far. Last year it revealed my alternator voltages was bad and I didn't even know there was a problem.

List of things to do:
1. Build new version / test dataloging capabilities.
2. Make it compatible with Nissan. I have all documentation ready to do so.
3. Spy AEM EMS serial communication and make it AEM compatible.

Jesters Deadd
04-15-2011, 12:29 PM
I am glad you have the 99 ECU! I am waiting for my null modem adapter to arrive so I can upgrade the firmware so I can read codes too.

tabasco122
04-15-2011, 10:49 PM
My car started stumbling really bad yesterday during a drive to the store and I was puzzled as to what the cause was. My front fuel trims went really lean (50) and my rear fuel trims showed very rich (150). Next I noticed there was no activity on the rear O2 sensor. Bingo, my rear O2 sensor died. My front O2 sensor died two years earlier and as a quick fix I substituted it with the narrow band O2 simulation from my WBO2 located in the collector. Having instant data access to the ECU certainly has come handy as my car gets older. I've solved two problems with it so far. Last year it revealed my alternator voltages was bad and I didn't even know there was a problem.

List of things to do:
1. Build new version / test dataloging capabilities.
2. Make it compatible with Nissan. I have all documentation ready to do so.
3. Spy AEM EMS serial communication and make it AEM compatible.

:D likes this

GTOX
04-21-2011, 05:17 AM
I think I will install mine soon, for those who have already installed, where is the best place for the pressure sensor hose to tap into?

green-lantern
04-21-2011, 11:16 AM
My car started stumbling really bad yesterday during a drive to the store and I was puzzled as to what the cause was. My front fuel trims went really lean (50) and my rear fuel trims showed very rich (150). Next I noticed there was no activity on the rear O2 sensor. Bingo, my rear O2 sensor died. My front O2 sensor died two years earlier and as a quick fix I substituted it with the narrow band O2 simulation from my WBO2 located in the collector. Having instant data access to the ECU certainly has come handy as my car gets older. I've solved two problems with it so far. Last year it revealed my alternator voltages was bad and I didn't even know there was a problem.

List of things to do:
1. Build new version / test dataloging capabilities.
2. Make it compatible with Nissan. I have all documentation ready to do so.
3. Spy AEM EMS serial communication and make it AEM compatible.

Hey, I about have the rest of the work done on my car so in the next week I should be on the road.

1. Can I get the null modem adapter at Radio shack?
2. Is there a firmware update I need on my unit?

Thanks

Goallie11
04-21-2011, 11:48 AM
I think I will install mine soon, for those who have already installed, where is the best place for the pressure sensor hose to tap into?

If you already have an electronic boost controller then just use the line that you used for that. If not cut your boost gauge line and use a T connector.

Hey, I about have the rest of the work done on my car so in the next week I should be on the road.

1. Can I get the null modem adapter at Radio shack?
2. Is there a firmware update I need on my unit?

Thanks

1. Yes
2. Have a look on that site he posted and see if theres a newer version then on yours. When you have it all hooked up hold the rotating button down when turning the car on and it'll show the version number.

green-lantern
04-21-2011, 12:03 PM
1. Yes
2. Have a look on that site he posted and see if theres a newer version then on yours. When you have it all hooked up hold the rotating button down when turning the car on and it'll show the version number.

Thanks

and it looks like I'm good, I'm running a 1st gen ECU

"91-93 cars: no changes"

Jesters Deadd
04-21-2011, 05:59 PM
You know what would be nice. A screen that showed a graph of boost vs rpm, kinda like the little graph that comes up on the peak boost screen. But if it had marks so you could tell the rpm the boost is falling off.

green-lantern
04-22-2011, 02:59 PM
Can I just hook my 0-5v wire from my AEM wideband to this thing then set the lowest and highest the gauge reads and I'm ready to go?

Goallie11
04-22-2011, 03:41 PM
Should be able to. Thats how I set my LC-1 to it.

green-lantern
04-22-2011, 03:47 PM
Good, thanks again

Jesters Deadd
04-27-2011, 12:01 AM
Hey on the little graph of boost vs rpm, what does the graph start and end at? Does it start at 2500rpm? And what is the max boost reading on that graph, 20psi?

BlackStealth
04-27-2011, 09:13 AM
Hey on the little graph of boost vs rpm, what does the graph start and end at? Does it start at 2500rpm? And what is the max boost reading on that graph, 20psi?
It starts at 2400rpms, ends at 7000rpms and increments by 200. The max PSI is 17psi (8 pixels high, 1 pixel in between two characters and another 8 pixels). Between each character it is separated by 1 pixel. On these character LCD display, there is no graphics, but I'm using some tricks to make simulated graphics.

Also do not be alarmed if your boost appears bumpy. If you're at 13.99 PSI, 14.0 PSI, 13.99 PSI it will show up as a ripple as the software is very simple. One pixel for 13.00-13.99 PSI, a different pixel for 14.0-14.99 PSI.

gs1000kat
04-27-2011, 12:58 PM
A HUD requires a special windshield (special coating). I can see that getting expensive pretty quick.

Those use different windshields, but I'm not so sure it is necessary. the Corvette guys swap in HUD to non-HUD cars all the time and have no issues. Might be better calarity, but it still works and they are quite happy with the result

green-lantern
04-27-2011, 01:25 PM
PSI Sensor= Int. Use internal pressure sensor 0.0psi to 36.3psi. Note that it does not measure vacuum.
PSI Sensor= Ext. Use external 4.0 BAR greddy pressure sensor (vacuum to 43.5psi) .

If I'm reading this right it appears I can use an external pressure sensor but I'm not finding any instructions on hooking that up. I was wondering if my old greddy profec could be hooked to this thing and show vacuum. The greddy doesn’t control boost anymore but it still reads boost on the screen.

Goallie11
04-27-2011, 04:14 PM
Hook it into the aux line I believe. It should be somewhere in the instructions.

green-lantern
04-27-2011, 06:04 PM
Hook it into the aux line I believe. It should be somewhere in the instructions.

I don't think it is but I'm going to use the aux for wideband so I guess I can't do it anyway.

green-lantern
04-27-2011, 07:05 PM
*WHITE <Analog Output>
Connects to any auxiliary unit that accepts a 0-5 volt input.
*BLUE <Serial Output>
Connects to a RS-232 com port for hyper-terminal data logging.
*

Hey real quick, I need to use the analog output right? or the blue RS-232 com port?

BlackStealth
04-27-2011, 08:02 PM
PSI Sensor= Int. Use internal pressure sensor 0.0psi to 36.3psi. Note that it does not measure vacuum.
PSI Sensor= Ext. Use external 4.0 BAR greddy pressure sensor (vacuum to 43.5psi) .

If I'm reading this right it appears I can use an external pressure sensor but I'm not finding any instructions on hooking that up. I was wondering if my old greddy profec could be hooked to this thing and show vacuum. The greddy doesn’t control boost anymore but it still reads boost on the screen.
If you disconnect the internal pressure sensor and hookup an external pressure sensor to it instead, it will work. Kinda difficult to do afterwards, that's why the "newer" version will have an external connector making it easier to switch between internal and external sensors. And no, don't use the aux input.

BlackStealth
04-27-2011, 08:03 PM
*WHITE <Analog Output>
Connects to any auxiliary unit that accepts a 0-5 volt input.
*BLUE <Serial Output>
Connects to a RS-232 com port for hyper-terminal data logging.
*

Hey real quick, I need to use the analog output right? or the blue RS-232 com port?
Analog output.

BlackStealth
04-27-2011, 08:04 PM
I don't think it is but I'm going to use the aux for wideband so I guess I can't do it anyway.
The wideband is just one wire, and the aux is just one wire, so there's no compromise. Each function is available.

green-lantern
04-27-2011, 08:26 PM
The wideband is just one wire, and the aux is just one wire, so there's no compromise. Each function is available.

OK, I see now, since they were on the same harness I thought. well lol nevermind. I think I have it now.

tabasco122
04-27-2011, 08:53 PM
old dogs and new tricks :-)

GTOX
04-29-2011, 05:37 AM
I wonder what software I should be running on my unit for my 1998 JDM GTO, AFAIK the later JDM ECUs were not flashable like the USDM equivalents so maybe they are different and I should be using the 1991-1997 software. I will try the 98/99 version first I think...

green-lantern
04-29-2011, 12:25 PM
Anybody running AEM wideband? How did you set it up? I cant seem to get mine to read correctly.

vr4tune
04-30-2011, 06:26 PM
When you make it AEM compatible will I just be able to plug into the serial port like the 19 port daisy chain Serial gauge that AEM makes? Because that would be pure bad ass.

JasonY
04-30-2011, 09:16 PM
Are these available for sale again yet?

Jason

BlackStealth
04-30-2011, 09:36 PM
When you make it AEM compatible will I just be able to plug into the serial port like the 19 port daisy chain Serial gauge that AEM makes? Because that would be pure bad ass.
Nope, it would get expensive to keep adding features. You have to use the analog 0-5volt wire that represents the AFR.

JasonY: I'll have new versions probably available in 7 weeks or less. I need to test the new design thoroughly.

green-lantern
05-01-2011, 12:29 AM
Are these available for sale again yet?

Jason

I'd strongly recommend jumping on it when they come available. The customer support is freaking great also.

GTOX
05-01-2011, 01:10 AM
^ Paul did you end up getting the AEM wideband working correctly with this unit? Keep us posted as if it doesn't work well I will get the Innovate instead of the AEM...

Noob question, both my laptops don't have null modem ports. Could I use a RS232 to USB adapter along with a null model cable to upgrade the firmware on this controller? something like this:

USB to RS232 Serial Null Modem Cable COM DB 9 Pin Lead | eBay (http://cgi.ebay.com/USB-RS232-Serial-Null-Modem-Cable-DB-9-Pin-Lead-/260750502683?pt=UK_Computing_CablesConnectors_RL&hash=item3cb5f0eb1b)

BlackStealth
05-01-2011, 08:22 AM
^ Paul did you end up getting the AEM wideband working correctly with this unit? Keep us posted as if it doesn't work well I will get the Innovate instead of the AEM...

Noob question, both my laptops don't have null modem ports. Could I use a RS232 to USB adapter along with a null model cable to upgrade the firmware on this controller? something like this:

USB to RS232 Serial Null Modem Cable COM DB 9 Pin Lead | eBay (http://cgi.ebay.com/USB-RS232-Serial-Null-Modem-Cable-DB-9-Pin-Lead-/260750502683?pt=UK_Computing_CablesConnectors_RL&hash=item3cb5f0eb1b)
Yup any USB to serial adaptor + a null-modem cable (or adapter) will work. Looks good.

green-lantern
05-01-2011, 12:17 PM
^ Paul did you end up getting the AEM wideband working correctly with this unit? Keep us posted as if it doesn't work well I will get the Innovate instead of the AEM...



Not yet, my car is down again. :( It looks like I got in a hurry and didn't tighten my timing tensioner pulley down well enough. It came loose

Vishnu
05-01-2011, 02:24 PM
Do you know if this would work with the Autometer Nexus's 0-4v data output feed?

tabasco122
05-01-2011, 05:17 PM
Do you know if this would work with the Autometer Nexus's 0-4v data output feed?

data would be misleading. If it actually does output data, then it wont work, his unit responds to voltage only. If the unit outputs a varying voltage that is directly equal to an AFR, then it should work. If it outputs a data signal, then it wont work.

Vishnu
05-01-2011, 08:35 PM
data would be misleading. If it actually does output data, then it wont work, his unit responds to voltage only. If the unit outputs a varying voltage that is directly equal to an AFR, then it should work. If it outputs a data signal, then it wont work.

I don't actually have the gauge yet, (want to get matching gauges all around if possible) but from what I've read everywhere it's a 0-4v analog signal for datalogging if that makes a difference. Not sure if it's a data signal or just varying voltage. Perhaps my use of "data" in my original post might be inaccurate to begin with.

tabasco122
05-01-2011, 10:44 PM
analog means its just a varying voltage, you should be good to go

Jesters Deadd
05-04-2011, 11:42 AM
So I was thinking of how to get my car to stop locking and unlocking it's self every time I turn off the car. I know its because of the LCD Boost controller. If I disconnect the wire/s from the ETACS and/or the remote locking system controller from the OBDII plug will it will stop? has anyone tried it?

BlackStealth
05-04-2011, 03:30 PM
So I was thinking of how to get my car to stop locking and unlocking it's self every time I turn off the car. I know its because of the LCD Boost controller. If I disconnect the wire/s from the ETACS and/or the remote locking system controller from the OBDII plug will it will stop? has anyone tried it?
Wow strange behavior. I don't get anything like that (lock / unlock). So if you disconnect the OBD2 connector it stops this behavior?

Jesters Deadd
05-04-2011, 03:46 PM
yep. I know it is the lcdbc because my other obd11 cables do it when I leave them connected. I have a 1.3 tantrix cable and a 2.0 tantrix flashing cable that do it too.

Jesters Deadd
05-04-2011, 03:48 PM
Does this happen to anyone else? Is any one else running this on a true 98-99 car?

GTOX
05-05-2011, 07:40 AM
^I will finish installing mine on my 98 this weekend hopefully. My car is JDM though so very different.

I tried to connect the controller via OBD-II, wouldn't connect and strange things happened like CEL appeared and ABS warning light started flashing (diagnostic mode?). Connecting via MUT works fine.

All the main things work, not sure how relevant the fault codes menu is for my ECU though, as I was getting quite a few fault codes coming up and not sure if they are just a result of the unit being optimized for USDM ECUs.

Simace
05-05-2011, 05:30 PM
Does this happen to anyone else? Is any one else running this on a true 98-99 car?

I don't have BlackStealth's system yet, but will when they become available. But I do want to throw this out there; using Tantrix 1.3u or 2.0 cables to the ODBII port does NOT lock/unlock the doors. It does, however, set the ABS light to flash - which is normal.

On the other hand, I had an alarm installed and recently, I have noticed that my doors will lock/unlock randomly. I believe that this is due to a faulty connection in the alarm system. Sometimes, I can't roll up my windows (or roll them down, depending on position they're in) and with a simple bump to where the alarms main unit is, the windows will operate (and sometimes the doors will lock/unlock). I've already scheduled a visit to the radio shop that installed my alarm to ensure this gets fixed.

So, with that, you might want to check to see if you have any loose connections.

Jesters Deadd
05-06-2011, 01:59 PM
I don't have BlackStealth's system yet, but will when they become available. But I do want to throw this out there; using Tantrix 1.3u or 2.0 cables to the ODBII port does NOT lock/unlock the doors. It does, however, set the ABS light to flash - which is normal.

On the other hand, I had an alarm installed and recently, I have noticed that my doors will lock/unlock randomly. I believe that this is due to a faulty connection in the alarm system. Sometimes, I can't roll up my windows (or roll them down, depending on position they're in) and with a simple bump to where the alarms main unit is, the windows will operate (and sometimes the doors will lock/unlock). I've already scheduled a visit to the radio shop that installed my alarm to ensure this gets fixed.

So, with that, you might want to check to see if you have any loose connections.
Was your alarm system installed before or after you you used the 1.3/2.0 cable? What year is your car?
Also this only happends if the cable is attached and you turn off the car.

Simace
05-06-2011, 06:20 PM
Before, and after of course. '99 (#26). The doors will unlock automatically when you turn off the car, and lock when you start up the car (shortly there after).

But as I mentioned, I know there is a loose wire that does cause the doors to lock/unlock (sometimes more than once in succession.) Hopefully, the radio shop will sort this out and fix it before it causes any real issues.

Jesters Deadd
05-06-2011, 07:10 PM
Before, and after of course. '99 (#26). The doors will unlock automatically when you turn off the car, and lock when you start up the car (shortly there after).
Hmm interesting. My car doesn't do that.

green-lantern
05-08-2011, 05:42 PM
I think I asked this before but is anybody running AEM wideband? If so what are the settings you are using? I can't get mine to read correctly.

BlackStealth
05-11-2011, 05:38 PM
I've tested the new design, made some changes, and submitted my order for a batch of new circuit boards to be made. Hopefully they will arrive in 2-3 weeks.

This new design has a bigger microprocessor (twice the memory) and has an onboard buzzer to alert the driver when something bad has happened (exceed knock threshold, coolant overheating, etc). This different microprocessor lets me control the brightness of Red, Green and Blue background LEDs. I find the LED to be too bright at night, so this will allow me to dim it down. I've made a small expansion card for datalogging, one expansion card model is for serial datalog communication, the second expansion card is bluetooth communication. I've put the SD Card datalogging off for now, but it's not difficult to add, just swap in a different expansion card.

green-lantern
05-11-2011, 06:24 PM
I've tested the new design, made some changes, and submitted my order for a batch of new circuit boards to be made. Hopefully they will arrive in 2-3 weeks.

This new design has a bigger microprocessor (twice the memory) and has an onboard buzzer to alert the driver when something bad has happened (exceed knock threshold, coolant overheating, etc). This different microprocessor lets me control the brightness of Red, Green and Blue background LEDs. I find the LED to be too bright at night, so this will allow me to dim it down. I've made a small expansion card for datalogging, one expansion card model is for serial datalog communication, the second expansion card is bluetooth communication. I've put the SD Card datalogging off for now, but it's not difficult to add, just swap in a different expansion card.

I tell you what, even though I'm having trouble getting the wideband to read correctly, I love this thing. By far the most useful tool I've ever had for the car.

CoopKill
05-11-2011, 07:57 PM
So awesome! I am waiting till the rest of my build is done to get this. I am usually the bleeding edge guy, but this on just keeps getting better!

Thanks man!

Goallie11
05-12-2011, 01:18 AM
So how much will the new unit be?

Jesters Deadd
05-12-2011, 01:22 AM
I've tested the new design, made some changes, and submitted my order for a batch of new circuit boards to be made. Hopefully they will arrive in 2-3 weeks.

This new design has a bigger microprocessor (twice the memory) and has an onboard buzzer to alert the driver when something bad has happened (exceed knock threshold, coolant overheating, etc). This different microprocessor lets me control the brightness of Red, Green and Blue background LEDs. I find the LED to be too bright at night, so this will allow me to dim it down. I've made a small expansion card for datalogging, one expansion card model is for serial datalog communication, the second expansion card is bluetooth communication. I've put the SD Card datalogging off for now, but it's not difficult to add, just swap in a different expansion card.

Cool, so you will hook up the early adaptors on the new design?

Jesters Deadd
05-12-2011, 01:26 AM
I tell you what, even though I'm having trouble getting the wideband to read correctly, I love this thing. By far the most useful tool I've ever had for the car.
I also love this thing. I look at it more than any guage I have now. With this thing I realized I had a bad habit of selecting to high a gear ant too low an rpm range. I was getting a bunch of knock and didn't realize it.

3000GT MR
05-12-2011, 02:08 AM
Are you still offering to upgrade are older units ?

BlackStealth
05-12-2011, 07:37 AM
I'll offer a cheap trade up program for those that want the latest and greatest.

jba3
05-12-2011, 02:30 PM
So I was thinking of how to get my car to stop locking and unlocking it's self every time I turn off the car. I know its because of the LCD Boost controller. If I disconnect the wire/s from the ETACS and/or the remote locking system controller from the OBDII plug will it will stop? has anyone tried it?


Does this happen to anyone else? Is any one else running this on a true 98-99 car?

If that happens with the tactrix or other OBDII cables installed, it's not the LCD controller itself. Sounds like it's still powering something after the car is off, or there's some kind of weird short going on. My car doesn't have that issue with the LCD controller, tactrix 1.3, or tactrix 2.0 - but my car is a 95.


I'll offer a cheap trade up program for those that want the latest and greatest.

My car should be out of the shop end of this week or early next week. :D

Jesters Deadd
05-14-2011, 02:16 PM
If that happens with the tactrix or other OBDII cables installed, it's not the LCD controller itself. Sounds like it's still powering something after the car is off, or there's some kind of weird short going on. My car doesn't have that issue with the LCD controller, tactrix 1.3, or tactrix 2.0 - but my car is a 95.

I am just trying to find out if other 98-99 have the same lock then unlock thing happen with their cars. I am not sure if its how the 98-99 were designed or if is an issue with my car only, but it only happends if one of the cables are plugged in.

JasonY
05-14-2011, 06:07 PM
I'd love to find out but i need one to buy first!

waits impatiently for the new batch to be ready for sale....:D

Jason

GTOX
05-15-2011, 02:05 AM
Anyone else using this on a JDM ECU?

GTOX
05-16-2011, 02:51 AM
I am just trying to find out if other 98-99 have the same lock then unlock thing happen with their cars. I am not sure if its how the 98-99 were designed or if is an issue with my car only, but it only happends if one of the cables are plugged in.

My 98 GTO does the same thing. I'm connected via OBDII/MUT and immediately after turning the car off it locks then unlocks, so I can confirm it's not just you.

Jesters Deadd
05-16-2011, 06:26 PM
My 98 GTO does the same thing. I'm connected via OBDII/MUT and immediately after turning the car off it locks then unlocks, so I can confirm it's not just you.

Well I figured out how to get it to stop. Just pull the pink wire from the keyless entry control unit to the data link connector that the obdII plugs into. It realatively easy. I already have the connector loose from its bracket to hide behind the side wall. I just pulled the gary flat pin holder out the back of the plug and there is a little black catch you can release from the front of the connector. I just let the pin hang there in case I want to reinstall it.

GTOX
05-17-2011, 06:03 AM
Thanks, i'll do this when I get around to it. I can't use my keyless remote to lock/unlock the car either when the lcd controller is plugged in, pulling the pink wire will remedy this too I guess?

Jesters Deadd
05-17-2011, 03:33 PM
Thanks, i'll do this when I get around to it. I can't use my keyless remote to lock/unlock the car either when the lcd controller is plugged in, pulling the pink wire will remedy this too I guess?
I didn't have this problem... my remote worked fine...

GTOX
05-21-2011, 05:34 AM
Yup any USB to serial adaptor + a null-modem cable (or adapter) will work. Looks good.

Damn I couldn't get the firmware update to work with that crappy ebay USB to RS232 adapter. I have the null modem adapter as well, not sure where I was going wrong...

Jesters Deadd
05-21-2011, 06:37 PM
You have to wait a sec once you start the firmware update on the computer before you turn on the key in the car. I thought I had a bad adapter then I realized i was turning the key on too soon.

BlackStealth
05-23-2011, 07:56 AM
You have to wait a sec once you start the firmware update on the computer before you turn on the key in the car. I thought I had a bad adapter then I realized i was turning the key on too soon.
Yup depends on how fast your notebook computer is. If you use an Atom processor, it may take a few seconds before the black screen pops up, and it waits for about 5 seconds for you to power up the boost controller before it times out.

J-Groove
05-23-2011, 11:57 PM
After seeing this in person, I am wanting one of these bad!

Great work!

-John

xwire
05-25-2011, 12:16 AM
very nice product, word on having it work on AEM cars?

FastOldGuy
05-25-2011, 11:58 PM
I want one of these for a AEM car. :)

GTOJOE
05-26-2011, 01:03 AM
I want one of these for a Vi-PEC car :p

BlackStealth
05-26-2011, 06:04 PM
I'm making a Nissan version next, followed by the AEM version.

hated
05-28-2011, 11:44 PM
Can you PM me the price on the current version? Thank you!!!

JasonY
05-29-2011, 01:43 AM
Available yet?

Jason

JasonY
05-29-2011, 08:33 PM
Also will this take an input for oil temp? Really trying to avoid extra gauges...thanks!

Jason

BlackStealth
05-30-2011, 07:48 AM
Also will this take an input for oil temp? Really trying to avoid extra gauges...thanks!
Sorry no, I don't have any documentation on oil temp gauges.

Maybe in 3 weeks I'll have something. I'm still waiting for the circuit boards to arrive by mail.

JasonY
05-30-2011, 02:33 PM
Okay, thanks! All sounds great so far! I guess that will be the 3rd gauge under my headunit. Wanted no gauges, but sometimes you just gotta have em!

Jason

tabasco122
05-30-2011, 05:09 PM
im sure you could find a digital gauge for that and mold it in somehow. instead of having the normal round type gauge. if its that important to you

twospoons
06-06-2011, 11:59 PM
Subscribed... Let me know when the new batch gets in.

rdmelton
06-09-2011, 11:02 AM
Is anyone that already has one of these going to the NG? I'd like to see one in person. I'm planning to buy one anyway whenever they're available, but it would be cool to see.

Alan92RTTT
06-09-2011, 11:07 AM
I believe Green Lantern has one.

I'm very interested as well.

Hans@GZP
06-09-2011, 11:16 AM
I saw Green Lantern's unit at the BRG. It is definitely badass. I'm ordering one as soon as they become available again. The user interface took about 1 minute to get used to.

Jesters Deadd
06-09-2011, 01:10 PM
I'll be at NG on Thursday and Friday...

tabasco122
06-09-2011, 02:54 PM
Yes, I got to see Paul's unit (lol) at brg, it was pretty win. Can't wait till its ported to Nissan. ..

Sent from my PC36100 using Tapatalk

green-lantern
06-09-2011, 04:17 PM
Yeah I got one and yes it’s badass for sure. I’ll be there Tuesday so anybody can check out my unit whenever they want.

Also if you want to see the LCD boost/scan thing I can show you that also. :D

FastOldGuy
06-24-2011, 10:33 PM
Any news on a AEM compatible model

What_Turbo_Lag?
06-27-2011, 10:38 PM
can't wait for the new model! what's the ETA?

J-Groove
06-28-2011, 10:10 AM
Just watched the videos you posted on these again. I am salivating for this product.

Again, great work, looking forward to buying one for my car once they are available. :)

-John

BlackStealth
06-28-2011, 02:37 PM
Main circuit boards have arrived and I'm soldering the components on. It takes me a lot of time to assemble because I verify each solder joint, and for extra safety measure I'm soldering both sides of the components whenever possible.

AEM version won't be available for a long time.

Jesters Deadd
06-28-2011, 03:14 PM
Can you make the lcd board adjust the brightness with a lead from the cars dimming circuit?