View Full Version : These silicone radiator hoses wont stop leaking
q2418130103p
04-10-2011, 10:25 PM
So last year I made a couple bad decisions.
1) The budget was running low, so I went with some knock-off silicone radiator hoses from china-bay.
2) I filled the car with whatever coolant I found at autozone.
No matter how much I tighten these hoses they WILL leak, and they not only leak when hot but they also leaked just sitting. The hose clamps are on so tight that the hoses are about to be damaged. My second mistake really isnt that bad, but since these pipes keep leaking I can see how gross and goo-ish this coolant really is, which makes me wonder what gross-ness is building inside my very clean and fresh engine.
I refuse to believe that I NEED t-bolt clamps for radiator hoses, so is it just the case that my Chinese silicone doesnt make a very good seal...? If so, I will just buy something nicer tomorrow and get them in before the weekend. The car is coming out of winter storage this weekend.
Thanks,
Jay
dodgers_fan
04-10-2011, 10:28 PM
What brand, or website did you get them from?
green-lantern
04-10-2011, 10:31 PM
If you are using stock clamps then that is your problem. Get better clamps, my samco hoses leaked with stock clamps. New regular clamps worked but I got T clamps later.
whitedevilstealth
04-10-2011, 11:18 PM
get the upper one from 3sx in the "one off parts" section. very thick hose then buy 2 t bolts the hoses are only 15 bucks
I have a polished stainless upper pipe with silicone couplers. I had the same issue with regular worm clamps and stock clamps. After going with tclamps not a drop since.
TUFFTR
04-11-2011, 05:26 AM
If not, use a bit of vaso under the hose so it creates a seal? Just a suggestion if your not using worm clamps..
q2418130103p
04-11-2011, 08:18 AM
hm, interesting. I guess I will go ahead and put on t-bolt clamps.
I am currently using worm clamps, not the stock clamps. Hopefully I haven't damaged the hoses the badly, silicone started pushing through the little holes in the worm clamp because I tightened then so much..
I have no idea what brand they are. I cant find then on e-bay anymore.
-EDIT- They are OBX hoses, half the cost of the samco.
TUFFTR
04-11-2011, 08:34 AM
Very strange man, I have OBX hoses on both cars, with worm clamps and have never ever had a leak!
whitedragon
04-11-2011, 08:36 AM
My OBX hoses leaked as well, and as soon as I got them nice and tight, they started weeping out of imperfections in the hose itself!
Guess who's going back to stock!
Pretty disappointing, since several other STL folks got their hoses the same time I got mine, and we're all switching back.
q2418130103p
04-11-2011, 08:39 AM
My OBX hoses leaked as well, and as soon as I got them nice and tight, they started weeping out of imperfections in the hose itself!
Guess who's going back to stock!
Pretty disappointing, since several other STL folks got their hoses the same time I got mine, and we're all switching back.
hm, whelp I can order some samcos and have them before the weekend, or I get try the clamps...
Anyone else have the same experience as whitedragon and I?
DrGonzo
04-11-2011, 10:03 AM
I ran the OBX hose before. I used t-bolts and they never leaked. The problem i did have was the goo from the inside of the hose did start to slowly creep out when the engine got hot so I know whatever they use to make the hoses is not that good and breaks down in the heat!!
q2418130103p
04-11-2011, 10:12 AM
I ran the OBX hose before. I used t-bolts and they never leaked. The problem i did have was the goo from the inside of the hose did start to slowly creep out when the engine got hot so I know whatever they use to make the hoses is not that good and breaks down in the heat!!
I didnt realize there was some sort of goo inside the hose, are you sure that wasnt your coolant? The yellow prestone junk, like the crap I used, gets goo-ey when it leaks out.
DrGonzo
04-11-2011, 05:25 PM
Nope... I was running straight water and a high psi cap so it wasn't anitfreeze
q2418130103p
04-11-2011, 05:30 PM
Hm, that is interesting.
I think I am going to flush this yellow junk out of mine anyway.
sublime_whatigo
04-11-2011, 06:09 PM
Interesting, I just put samco's on my car with stock clamps, full of fluid but hasn't been started/pressurized yet. The stock clamps are much better then your average worm clamp imo. I guess if it leaks I have some high quality worm clams as there is no way in hell I'm putting t-bolts on them.
zelstin
04-11-2011, 09:10 PM
You've been running water, the inside of the cooling system will be rotting away, the fittings that the hoses go onto will be starting to crumble, that'll be why they leak, probably the headgasket will be leaking too causing too much pressure in the cooling system, hence more leaking.
Steve
Da Fck? No No No No No
J. Fast
04-11-2011, 09:41 PM
Da Fck? No No No No No
Please enlighten us zelstin and post some information behind your reasoning instead of always acting like a little troll. I thin k what steve here is getting at is water offers no corrosion protection to an aluminum block. It lends certain types of headgaskets to localized heating which will lead to premature breakdown. Do you learn all this shit on the internet or from working on performance vehicles?
mb3000
04-11-2011, 09:57 PM
:popcorn2:
DrGonzo
04-11-2011, 10:38 PM
You've been running water, the inside of the cooling system will be rotting away, the fittings that the hoses go onto will be starting to crumble, that'll be why they leak, probably the headgasket will be leaking too causing too much pressure in the cooling system, hence more leaking.
Steve
First off water will not corrode aluminum. Aluminum reacts to water by forming aluminum oxide on it's surface. This aluminum oxide layer is chemically bound to the surface, and it seals the core aluminum from any further reaction. Unlike steel/iron which forms rust which puffs and flakes off exposing more raw material. About 60% of the cooling system is made of aluminum, 30% are hoses and the last 10% is steel/iron. All my steel fittings were replaced with aluminum ones. the only thing left that is not aluminum if the coolant crossover tube which I had the inside coated with high temp urethane to protect it from the water.
So the only thing exposed is the MLS headgasket which I have a better chance of blowing due to running the car than the 5-8 years it would take the distilled water to rot it away to the point it would cause any issues.
As for the pressure yes it is a little higher due to the lower boiling point of the straight water compared to the Ethylene glycol used in standard antifreeze but not by much 15 psi with antifreeze vs 19-20 psi straight water. If the system is in good shape it will easily hold the pressure. If your hoses and gaskets are rotting away then no it won't hold!
The reason for running straight water is that is has better thermal heat displacement than Ethylene glycol mix. I can lower my running temps by 15-20 under hard load running straight water. Add Water Wetter and I can drop almost another 15deg so that a 30-35 drop in running temp.
Now don't get me wrong I never store the car with just water in the block. If I am not going to be driving it for a while I ether drain the system or 50/50 mix it in the winter time so I don't freeze the block.
I work to much on the engine to be buying antifreeze every week cause I need to pull a hose or pull the radiator.
Now Back to the OP!!
J. Fast
04-11-2011, 10:49 PM
We have to change the head gaskets on roadcouse about every 3/4 races or so (2000 miles maybe) or the headgaskets pop from running straight water. Never had any heating issues, not one actually, and we could actually run 2-3 more psi of boost at the track vs 50/50 on the dyno. It does have it's advantages though, We use cheap headgaskets though since we change them like oil filters.
q2418130103p
04-11-2011, 10:57 PM
Please, feel free to change the topic, I've got what I need to know. I am just glad I am not alone with the leaking problem. That leaking is one of the few flaws in my engine bay, having a puddle of coolant on top of a bright shiny silver transmission is very dis-heartening. At first I was concerned that my system may be under too much pressure, since it has a 19psi cap. I will go ahead and put on some t-bolts, and I will likely change to something other then prestone yellow. If it still leaks with the t-bolts then I will get something not made in china.
DrGonzo
04-11-2011, 11:04 PM
If your running a 50/50 mix you should not be using a high psi cap. the high PSI caps are for water or low antifreeze mixes so that when they do start to boil they don't blow out the overflow bottle. If your running antifreeze you need a stock cap. If you have to run a high PSI cap and antifreeze then something is wrong as the system is not cooling properly and the car is running too hot. Most likely due to a bad radiator core that is rotted out and not dissipating the heat properly.
If you drain the coolant after running it what color is the coolant?? If it's brown then you got problems!!! Most likely a bad radiator.
q2418130103p
04-11-2011, 11:10 PM
If your running a 50/50 mix you should not be using a high psi cap. the high PSI caps are for water or low antifreeze mixes so that when they do start to boil they don't blow out the overflow bottle. If your running antifreeze you need a stock cap. If you have to run a high PSI cap and antifreeze then something is wrong as the system is not cooling properly and the car is running too hot. Most likely due to a bad radiator core that is rotted out and not dissipating the heat properly.
If you drain the coolant after running it what color is the coolant?? If it's brown then you got problems!!! Most likely a bad radiator.
It drains out nice, and I have a real temp gauge on the car as well. While I am not sure what good temps are, it is always below 100c. The outside of the radiator is in perfect shape, I forced some water through it last season, and it came out clean as well.
I will go ahead and get a stock PSI cap.
DrGonzo
04-11-2011, 11:31 PM
My running temp on my TT is about 185-190F on my Prosport EVO's with it being 80 degrees outside. This is running antifreeze and stock cap all stock cooling.
Service Manual calls for range of 176-203F
q2418130103p
04-11-2011, 11:35 PM
My running temp on my TT is about 185-190F on my Prosport EVO's with it being 80 degrees outside. This is running antifreeze and stock cap all stock cooling.
Service Manual calls for range of 176-203F
I cannot remeber exactly what the running temp is, but on the highway I believe it is around 85c. At idle is will get into the 90s, it is always below 100c as I mentioned before.
q2418130103p
04-11-2011, 11:39 PM
Cooling is not helped with this stupid FMIC either. I was planning to go with some aluminum radiator to help, I just havent gotten around to researching them yet.
q2418130103p
04-12-2011, 12:30 AM
I have gotten a bit lazy in my old age, and between that and my other motor projects I dont really feel like flushing the system myself with a garden hose. Is there any reason I cant go to the local mechanic who has the power flusher and have them do it? There is 0 chance of there being rust/sediment in this engine, maybe the radiator, but certainly not the engine.
Also, what coolant can I get that has minimal other chemicals in it? Is there something out there that just offers freeze and rust protection without having stuff that seals old gaskets, or whatever these special coolants do now?
zelstin
04-12-2011, 04:29 AM
Please enlighten us zelstin and post some information behind your reasoning instead of always acting like a little troll. I thin k what steve here is getting at is water offers no corrosion protection to an aluminum block. It lends certain types of headgaskets to localized heating which will lead to premature breakdown. Do you learn all this shit on the internet or from working on performance vehicles?
Okay Drmbldr, J.Fast, Steve68's_keeper, or whatever you call yourself these days. I promise to stop acting like a little troll in the wake of horrible advice.
BTW I learned all this shit from working on performance cars. That is, when I wasn't pretending to be an airborne ranger.
Okay Drmbldr, J.Fast, Steve68's_keeper, or whatever you call yourself these days. I promise to stop acting like a little troll in the wake of horrible advice.
BTW I learned all this shit from working on performance cars. That is, when I wasn't pretending to be an airborne ranger.
LOL ouch
DrGonzo
04-12-2011, 08:00 AM
Okay Drmbldr, J.Fast, Steve68's_keeper, or whatever you call yourself these days. I promise to stop acting like a little troll in the wake of horrible advice.
BTW I learned all this shit from working on performance cars. That is, when I wasn't pretending to be an airborne ranger.
Explain what you think is horrible advise?? Ok, so they have iron block and aluminum heads but I knew what he was getting at. You obviously did not.
You have yet to actually add anything constructive to the conversation at all even though you admit to "learning at this shit working on performance cars", so unless you have something to actually add stop trying to start drama.
And what the hell does you supposedly being an Airborne Ranger have anything to do with the conversation, Is that supposed to scare us into taking you more seriously? Sorry but that's not going to happen. I have a good feeling your lying about it anyway and just threw that in they to make yourself sound better. Just an FYI! I am ex-military and I did tour with the 82nd and 75th Ranger Reg in Iraq in 2003.
q2418130103p
04-12-2011, 08:27 AM
That's why the olds 215 engine was a total failure.
The yanks sold it to the poms to be a Rover 3.5. Even the poms refused to put antifreeze in them.
All modern Jap engines have aluminium heads. Iron blocks /aluminium heads act as an electrolytic cell, one metal is the positive electrode, the other is the negative electrode and they're bolted together. Put water in the cooling system, it's called electrolyte. It doesn't take long for the water to turn brown, the top of the block starts rusting on the gasket surface(as well as everything else) then the headgasket starts leaking, first sign being the overflow bottle that needs topping up.
That's why higher pressure caps are fitted. It's to mask the problem until it gets worse and hoses start leaking, hoses pop, then the radiator top tank pops.
Obviously the stock radiator isn't up to the job, time for an aluminium "ricer" one.
Then to fix it properly after all the damage is done , the block needs resurfacing to remove the rust, rust being porous.
Steve
lol, you nearly described my steps exactly, except I am not using straight water. So I suppose those steps are about the same for any cooling issue.
Although I didn't realize that a higher PSI cap was a stop-gap measure, I just thought it was perdy. And my coolant isnt brown, yet.
I am not sure if I will call an aluminum radiator 'ricer' though, I dont think a larger radiator core can really be considered a bad thing. Now... if the change is prompted on account of an FMIC, like mine is, then you probably have a case.
BTW, how can the radiator tank pop, doesn't it have a direct vent to atmosphere?
q2418130103p
04-12-2011, 08:32 AM
The easy way out is to throw in a bottle of chemiweld, that might fix it for a couple of months, then you could even pass it off to some young, innocent, unsuspecting new owner. That's if you don't want to fix it.
Steve
Hey Steve,
I am not sure to whom you are referring, I believe that the one guy to mention that he was running straight water was doing so without any leaking issue like I was referring to.
q2418130103p
04-25-2011, 08:25 AM
I dont remember if I mentioned this or not, but the old coolant drained out its usual yellow/green color, so it was burnt.
I went ahead and flushed through some distilled water, just because I dont like the yellow stuff. I picked up some regular uncut sierra stuff to top it off later.
I put on thermalflex hoses, and the factory radiator cap.
If was only around 70°F here yesterday, I dont remember what the idle temp got up to, I believe it was just below 80°C. Whatever it was, it was just hot enough for the 1 rad fan to kick in, and just cold enough that the rad fan would only run for 5 seconds.
I am going to have to wait until it gets hotter around here to really see what is up.
J. Fast
04-25-2011, 06:22 PM
Okay Drmbldr, J.Fast, Steve68's_keeper, or whatever you call yourself these days. I promise to stop acting like a little troll in the wake of horrible advice.
BTW I learned all this shit from working on performance cars. That is, when I wasn't pretending to be an airborne ranger.
DAM, I missed your post...
LOL, I'll have to remind myself I was pretending to be an airborne ranger when I exited a perfectly good aircraft with a combat loadout 27 times while assigned to 2nd Ranger Batt you keyboard racing fuckhead!
DocWalt
04-25-2011, 06:35 PM
How about we chill out and take this thread back to where it belongs.
You need t-bolt clamps or lined worm clamps like so:
http://lh3.googleusercontent.com/public/teWMn7c8hIc11j3MxQGKY0Hzckg85-WFcYsuaoezFpbgnk4B6sRCBmGLDTuTfzFCm9zygUVQ6tomh1F3 XYYxFqzdh67j0wzwSWl7Ze7ZRIs2afAxmCI5CBA1O7ewX2m033 853DKa_5GdN-6-mu1xobcXHEy7D0-w7ZheJBNqlBA5dWjNvoDTLhlcCY_IIGYrYZE6k590IWDSa8rrj qEqn2d5gM1ai9dnNDYVq8eITr4OeNGRQgwFiu-Lm1zn6VJtyQ
sublime_whatigo
04-25-2011, 09:31 PM
^Good clamps!
Just took my car out for the first time with the new samco hoses and stock clamps. No leaks, you guys are doing it wrong :)
q2418130103p
05-29-2011, 09:08 PM
Update:
I put on some better silicone hoses, so far they are holding with regular hose clamps. The old hoses worked at first too, so that doesnt really say much. I also put on a stock cap and I am running ~50/50 sierra and distilled water.
The hi temp today was around 85F. The hottest I saw on my gauge was around 192F.
In case anyone is interested here are the fan temps from teh manual.
Rad Fan Off->On @ 178F-192F
Ran Fan On->Off @ 171F
AC Fan Off->On @ 196-210F
AC Fan On->Off @ 189F
Some older posts on other forums have different ranges for these, much higher ranges, like 240F for one of the fans. I am not sure where those numbers came from, but I am going to stick with the manual.
As far as I know, the AC fan never came on, so either its temp probe is defective or inaccurate or the car never hit the required range.
I cannot actually find an 'operating range' in the manual.
One thing I thought was odd is that the temps were higher on the highway than at idle. On other cars I usually see this the other way around, the increased air flow at highway speed usually reduces the temp (assuming you are driving at a sane cruising speed). I assume this is a result of having an FMIC. This really bothers me. Does anyway have any suggests for this? Even if you suggestion is to ditch the FMIC, I am interested in hearing your story.
Chris@Rvengeperformance
01-13-2015, 11:21 AM
fyi I have a lower samco hose leaking too, I think stock is better...
sergechronos
01-13-2015, 11:40 AM
Working on your necromancy skills eh?
Chris@Rvengeperformance
01-13-2015, 12:07 PM
Working on your necromancy skills eh?
yep, forum needs more info!
FYI, you are required to read my post in the same tone and cadence as "sometimes, dead is better" from Pet Sematary.
sergechronos
01-13-2015, 12:19 PM
You act like forums are for learning and good discussion..
Your requirement has been duly noted
q2418130103p
01-15-2015, 08:12 PM
My new hoses have been fine, but I haven't really driven it much since this thread started.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.