View Full Version : ARC2 help (with logs, problem possibly unrelated to ARC2)
Frostedbutts
04-10-2011, 07:20 PM
I've been having an issue with my car running like a piece of shit. My fuel setup is:
Hotwired Walbro
Denso 720cc
AEM FPR
ARC2 w/ 87mm MAS
Low -5
Mid -7
High -6
Accel +3
(this setup was posted by Hellbringer on 3si, who had roughly the same mods)
The first problem I'm having is that my ARM1 ALWAYS reads the second to last lean light. I've already tried adjusting the low knob everywhere from -5 to +5/6 and the ARM1 refuses to dither. My o2 voltages change for a minute or so on my logger and then go back to sticking at certain numbers, after the car warmed up this most recent time I started it, it was:
Rear o2: .80-.95
Front o2: stuck at .99
ARM1 reading lean as always and idle at ~800. Which is odd because those o2 voltages are rich as hell, right? It shouldn't even be running if it's reading constantly that rich. The weird part is that this area of the log is where the car runs best.
When I first started the car it was:
rear o2: .03-.06
front o2: .11-.15
ARM1 reading lean. Idle ~1000.
Eventually after it warms up the idle smooths out for a bit and then it slowly dies. Vacuum is reading -50~ hkpa at idle.
Log here:
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidEMySTZPMGVhak0xeUk5NjYzMUI5S 1E&hl=en
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidHFOQVF0bHduTC1CQkxlWEhVeFJ1R EE&hl=en
mb3000
04-10-2011, 09:38 PM
Log please
Frostedbutts
04-10-2011, 10:12 PM
Logs here:
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidEMySTZPMGVhak0xeUk5NjYzMUI5S 1E&hl=en
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidHFOQVF0bHduTC1CQkxlWEhVeFJ1R EE&hl=en
1gRick
04-11-2011, 01:26 AM
Logs here:
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidEMySTZPMGVhak0xeUk5NjYzMUI5S 1E&hl=en
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidHFOQVF0bHduTC1CQkxlWEhVeFJ1R EE&hl=en
Not trying to be mean spirited but I thought these things were supposse to be so easy to tune, for almost 1k they should be. I was thinking of getting one but now I don't know.
Frostedbutts
04-11-2011, 01:51 AM
As stated in the title, it is possible that this problem is unrelated to the ARC2.
J. Fast
04-11-2011, 02:25 PM
Something is going on with the rear bank or O2 Trev. Pull the sensor out and test it with some brake cleaner on a rag and see if the voltage changes. If it stays pegged it's toast. Since I know you already changed the plugs and wires, if it's good do a boost leak test and then a fuel pressure test. Then do a compression test on the rear bank.
1gRick
04-11-2011, 03:40 PM
I sure hope so. Maybe try calling DNP as someone there is an expert on these. GL
Frostedbutts
04-11-2011, 05:24 PM
Something is going on with the rear bank or O2 Trev. Pull the sensor out and test it with some brake cleaner on a rag and see if the voltage changes. If it stays pegged it's toast. Since I know you already changed the plugs and wires, if it's good do a boost leak test and then a fuel pressure test. Then do a compression test on the rear bank.
Cool, I'll grab a sensor from my other car and try one of those as a replacement. How hard is this thing to change without the "special socket" from mitsubishi?
mb3000
04-11-2011, 08:30 PM
You can get the special socket from autozone or a similar store. IIRC it's a 7/8".
gltasn
04-11-2011, 09:15 PM
my vac at idle is -18, my arc2 #'s are +2,-7,-3,+1(felt clicks not, dot style indicators.) ive got 720's with the big mas,dual wallys, and 2 steps colder plugs.
Frostedbutts
04-11-2011, 11:04 PM
Are your settings with this MAF?
http://www.stealth316.com/images/gran87_side1.jpg
Once I get the rear o2 reading figured out I can go from there with my tune. Also, my vac reading should be a little off from everyone else's since I'm in Denver.
Lugnut
04-12-2011, 12:09 AM
Sorry if I missed it ... Is this a Dynamic Racing ARC2 ...
Frostedbutts
04-12-2011, 12:43 AM
Not a DR-ARC2, no. But it is the correct ARC2 for our cars. R5 maybe? I forget the exact number but that was the first thing I checked.
gltasn
04-12-2011, 09:54 AM
Are your settings with this MAF?
http://www.stealth316.com/images/gran87_side1.jpg
Once I get the rear o2 reading figured out I can go from there with my tune. Also, my vac reading should be a little off from everyone else's since I'm in Denver.
mines a gp-r5(correct model #, bought from dr 8 years ago) and i use the 4" maf.
Frostedbutts
04-12-2011, 01:25 PM
One of your oxy sensors is obviously a dud. maybe both of them?
Jap cars don't have imperial nuts & bolts either, 23mm?
The ARC2 comes in 2 different versions that I'm aware of, When I bought mine about 11 years ago (GT Pro I think) it was a version 2 but they supplied the wrong (Version 1) installation instructions. The difference is in the IPS wiring, the later ones the lead goes to 12V rather than the idle position switch. Getting that part wrong screws everything up. It makes the ACC adjustment work only when off idle rather than AT idle.
Steve
I have the newer version where TPS wire is unused.
mb3000
04-12-2011, 06:11 PM
Make sure you don't have the "K" version. IIRC that one was designed for DSM's.
Frostedbutts
04-13-2011, 02:27 AM
It's the R5. The o2 sensor socket I bought today didn't fit the sensor - it wasn't long enough to get all of the head of the o2 sensor on it. I returned it for the open ended one, hopefully that will work.
Chris@Rvengeperformance
04-13-2011, 10:55 AM
I find a wrench works better anyway. You can get to the front one from the bottom without removing anything at all and if you bend your rear heatshield over a bit you can have the rear out if you just move the rear intercooler pipe over.
I can swap both now in about 35 minutes.
Frostedbutts
04-13-2011, 06:59 PM
Yeah I did the rear (no heatshields) just now in about five minutes. That was WAY easier than I expected, I used a 3/8" drive with a breaker bar and one of these:
http://lh3.googleusercontent.com/public/78ASLuEkJV-8pqnkjiXBH2kI03_5SZ8ldUgNFNoCG75YJdqEavBMbXO10ZBPT k17rYd1KdOV_gxtil4u_V3mEh4Wf0PPZRJqXHdjxmmGZie96QC 28kL1KV-nR2u94TwfF4RIvoKc67cErWVhVVmGcN72cqT54VTmzHXFcLx89 0j4p_E9WNX33w
It came off really easy. I have to work otherwise I'd start messing with it, but anytime I do that I get carried away and end up being late.
gltasn
04-13-2011, 07:03 PM
make sure and antisieze the threads when putting in a new one if, it doesnt come with any allready on it.
Frostedbutts
04-14-2011, 08:48 PM
Replaced the rear o2, put anti-seize on the threads, almost shit myself when it started smoking from the rear, and then I realized it was the anti-seize.
Having just about the same issue now, though.
1. The ARM1 is STILL reading lean 100% of the time.
2. The car did run decent while it was warm, but still not where it should be. Runs like absolute shit when cold. When starting the car I sometimes get a CEL, but then it goes away after a second.
3. Once warm the MAF sensor is pinned at 37.4, is that a sign of a bad MAF? When warming up it's all over the place.
ARC2 settings for these logs are listed as the title of the sheet. Each different log is as a sheet in the excel spreadsheet (at the bottom of the page)
Logs below, any ideas?
https://spreadsheets.google.com/ccc?key=0Avkhi76V_zGidGFLbkZtbmhkYWtyNnQyYkhaU2dCW VE&hl=en
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.