View Full Version : OK, changed fuel pump, still cuts out
Sin'sVr4
03-31-2011, 12:40 PM
both the pump and fpr are fine. i will post vids of the fpr later that i took this morning. My mechanic thinks im not getting solid spark. Lunch time im going to check for spark. wonder if a coil pack or cas went bad?
http://www.youtube.com/watch?v=jPO7ebQEQho
http://www.youtube.com/watch?v=hdBPbOcCUsU
checked and do have spark.. but was checkin all connectors and broke the big one on the PTU. so, it needs a new connector :(
CoreyB
03-31-2011, 01:17 PM
Its not a coil pack, you have 3 and it would still run if one went bad. I would connect power directly to the pump so it cant shut off and then start her up and see what happens.
Sin'sVr4
03-31-2011, 01:43 PM
i think my cas might have gone bad. im gonna check for spark at lunch and go from there. if it doesnt work ill do the direct power thing....
Sin'sVr4
03-31-2011, 02:36 PM
put the videos on there now
CoreyB
03-31-2011, 02:51 PM
Ok Not a fuel pump problem. For whatever reason its going very lean and dying.
mb3000
03-31-2011, 06:48 PM
Ok Not a fuel pump problem. For whatever reason its going very lean and dying.
Possibly a few clogged injectors?
UTRacerX9
03-31-2011, 06:58 PM
Check the wiring to the fuel pump. I run mine direct off the battery to a relay. I originally used 12 gauge wire, and experienced some cutting out under hard accel. Came to find out that my fuse connection was not making great contact, and it had actually melted the plastic and caught on fire. Switching to a heavier wire and different fuse setup ensured the pump was getting all the volts needed, didn't have a problem after that.
Sin'sVr4
03-31-2011, 07:08 PM
mines hotwired and uses 10 guage. i am getting 13v (for the most part.) on and at idle. My pump is fine. there is something else going on there. maybe i will run some injector cleaner thru there. maybe the E85 dislodged some carbon and and gunk and clogged some injectors?
J. Fast
03-31-2011, 07:13 PM
Did you clean the injectors and fuel filter before you made the switch from pump gas? I wouldn't run any injector cleaner in there. I'd pull the injectors and fuel filter before dumping that garbage in there.
You're sure you didn't foul the plugs when it was stuck at wide open throttle and bouncing on the rev limiter?
Sin'sVr4
03-31-2011, 07:29 PM
I have a new fuel filter on there now. replaced it after I was already on E85. The injectors i put in and ran pump for maybe 200 miles? not sure J. I got the new PTU connector and will put it on tonight. and I will change the plugs tonight too. Im using iridiums right now...i know i know, but they were brand new and didnt want to tear the top end off. Will have new results hopefully tomm. Gonna do a compression test tonight also. Dont need to but want to for shits and grins
UTRacerX9
03-31-2011, 07:34 PM
Checked the ground wires?
J. Fast
03-31-2011, 07:35 PM
Hopefully that's it. Driver unit was probably wiggin out. Did you make sure to check all your ingnition fuses and the ignition lead wire? I remember when you got it back from Under Pressure Performance and I scoped it CK had monkey fucked the lead wire and it was shorting.
TwIzTeD_3kGt
03-31-2011, 08:09 PM
Sorry for the off-topic, but what's wrong with Iridium's?
Intropy
03-31-2011, 09:42 PM
Did you ever try simply adding more fuel? I know your tune supposedly didn't change, I'm just interested if that might help. It seems to start pretty damn reliably, so I don't think it's plugs. It's like the all-injector initial pulse is giving it enough fuel but then it runs out.
CoreyB
03-31-2011, 10:24 PM
Not the pump because it builds pressure while running, not the plugs because it starts good, and the injectors sound fine. The problem is with the injector pulse like intropy said or whatever is causing fuel to not be sprayed.
Sin'sVr4
04-01-2011, 01:56 AM
ok. pulled the return line and fuel pumped right out of it. checked the aem on the lappy and pulse width inj was 6120 u prety much all exactly the same when i was cranking. spliced in a new ptu connector. changed the plugs to coppers and i have no spark at all now. wtf? not sure why, but i have no spark at all. put the iridiums back to see if that changed but still no spark? everything is connected and hooked up. I have no fukin clue what is going on now and feel like getting rid of the car. I even went out and bought a new battery. swapprf ptu's and still no spark. all wires from new splice are good. I dont know enough abou this car to trouble shoot bymyslef. My buddy was wth me but doesnt know alot aout this side of the car either. what do i do?
Intropy
04-01-2011, 03:30 AM
what do i do?
Back to basics - did you check fuses?
While turning it over, watch and see if the "Stat Sync'd" channel comes on. That will tell you if the AEM is seeing the appropriate crank/cam signals.
CoreyB
04-01-2011, 10:34 AM
Has to be related to the PTU for your current problem. You had spark before you broke the PTU connector and after fixing you dont. Either the wiring is not truly correct, you blew a fuse or somehow damaged the AEM. Check for a pulse signal at the PTU connector if all the fuses check out. With a analog volt meter you would see the needle bounce from 0 to 3 volts back and fourth while cranking.
On the big connector the 3 wires closest to the center of the PTU are your signal wires.
Roybatty
04-01-2011, 11:14 AM
It'll be computer related.
Afterall it fires up OK, it just dies afterwards.
Steve
+1, not ringlands ;) Had exact same problem for a long time. After going through all fuel and spark issues; ended up being a bad MAFS. I understand your intake setup is mafsless; recommend you focus on your piggyback and sensors as others suggesting.
Did anyone add "patience of job" to the tips thread???
Sin'sVr4
04-01-2011, 11:16 AM
the ptu splice was simple. connected same color wires to existing same color wires. have 2 ptus and tried both and both are known good. gonna try a different coil pack. yes the stat sync came on too on te aem...
CoreyB
04-01-2011, 11:53 AM
How about rather than swapping out parts, test them instead. If you dont know how there are people here who can help.
Intropy
04-01-2011, 12:25 PM
yes the stat sync came on too on te aem...
This tells you that your crank/cam angle sensor is good.
Do you have power to the PTU with the key on? Did you check fuses, especially #1 in the bay and #12 (I think) in the cabin?
Sin'sVr4
04-01-2011, 12:30 PM
yes, eci fuse is good, and ign coil fuse (#12) is good also). I tested the coils and got .73 reading on most. coil pack plug got .39 from 3-1, 3-2, 3-4. PTU, just need to do the battery tester thing from stealth 316. What else should I test?
Intropy
04-01-2011, 12:38 PM
What else should I test?
Test for power to the PTU with the key on, and test the ground side - you can hook a test light to the positive terminal and touch the harness wire that goes to ground on the PTU.
CoreyB
04-01-2011, 12:48 PM
And test for power at the coils themselves and I would still suggest checking for the pulse signal I mentioned.
Sin'sVr4
04-01-2011, 12:54 PM
on the inj? i saw the pulse #'s on the aem and they were all exactly identical when cranking. I wish i was more versed in these testing practices, to ensire imn not doing them wrong
CoreyB
04-01-2011, 01:02 PM
No the ignition pulse. The AEM sends 3 5V square pulse signals to the PTU to switch it on and off. The PTU has transistors that when they recieve the 5V pulse short the primary coil in the coil packs. When the primary coil is shorted the magnetic field collapses inducing a voltage on the secondary coil which is connected to the spark plug.
Sin'sVr4
04-01-2011, 02:04 PM
and i test for this how? any walk thru guides? I have the manuel but its like reading stupid for me right now.
CoreyB
04-01-2011, 02:07 PM
Use a analog voltmeter, connect to one of 3 wires on big plug going to PTU thats toward center, while car is cranked you will see 3v bounce on meters needle if you are getting signal.
Sin'sVr4
04-01-2011, 02:28 PM
and if i dont have an analog voltmeter? the c battery should work right?
CoreyB
04-01-2011, 02:29 PM
No thats just to test whether PTU works. Wont test signal.
Sin'sVr4
04-01-2011, 02:30 PM
so, when im cranking the car, and the start sync says "on" it means the cas is good? its getting a signal right? How do I test my coils? car on? car off? what should the resistance be? just would like to know from you guys that can tell me.
CoreyB
04-01-2011, 02:32 PM
Here Stealth 316 - Ignition Coils (http://www.stealth316.com/2-ignitioncoils.htm)
Sync light means that AEM is recieving signal from CAS but doesnt tell you if its sending one to PTU.
Sin'sVr4
04-01-2011, 02:39 PM
ok, but i dont have a analog voltmeter....so what do i do to test for input signal to the ptu?>
CoreyB
04-01-2011, 02:43 PM
If you can get to a store a meter is less than $10, A test light that goes down to around 5v will work too.
Sin'sVr4
04-01-2011, 06:17 PM
ok i got an analog meter and tested the ptu, like the manuel and stealth 316 says, and the ptu itself is good. i have continuity on all 3 pins so thats good. eliminate that for now. Now I need to test the coils with a test light
Sin'sVr4
04-01-2011, 08:06 PM
i have the aem twin fire, would that do anyhting?
CoreyB
04-01-2011, 08:17 PM
You still need to check for a signal to ptu from aem....
Sin'sVr4
04-02-2011, 12:11 PM
i can check that tonight. Im pretty sure my coil is done. i was getting very low readings. i ordered a new coil pack from mitsu and will be here tues. so, we'll see. I will test the rest of the line tonight tho...
Chris@Rvengeperformance
04-02-2011, 12:44 PM
can you wire around that aem cease fire for a bit?
Intropy
04-02-2011, 12:45 PM
aem cease fire
I lol'd.
Sin'sVr4
04-02-2011, 12:50 PM
um, ....?
Chris@Rvengeperformance
04-02-2011, 12:51 PM
um, ....?
the aem "twin fire" has a high failure rate.
Sin'sVr4
04-02-2011, 12:55 PM
its not installed.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.